Table of Contents
Advertisement
Note
f Backup function is enabled when [BACKUP INPUT MODE] is set to [1], and the same signal is input to the <DVI-D IN> and <HDMI IN>
terminals.
Alternatively, the backup function is enabled when [BACKUP INPUT MODE] is set to [2], and same signal is input to the <SDI IN 1> terminal
and the <SDI IN 2>.
f To switch to the backup input signal using the backup function, make sure that the following three conditions are satisfied to be ready to use
the function.
g Set [BACKUP INPUT MODE] to anything other than [OFF].
g Input the same signal to the primary and secondary inputs.
g Display the image of the primary input.
f If the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to use
the backup function is canceled. To switch to the backup input signal using the backup function again, switch to the primary input.
f [BACKUP INPUT STATUS] is displayed in the input guide (x page 118) and [STATUS] screen (x pages 73, 142) when [BACKUP
INPUT MODE] is set to anything other than [OFF].
When switching to the backup input signal is possible using the backup function, [ACTIVE] is displayed in [BACKUP INPUT STATUS]. When
it is not possible, [INACTIVE] is displayed instead.
When [BACKUP INPUT STATUS] is [ACTIVE] while the image of the primary input is displayed, the secondary input becomes the backup
input.
When [BACKUP INPUT STATUS] is [ACTIVE] while the image of the secondary input is displayed, the primary input becomes the backup
input.
f The input is switched seamlessly when the inputs of the DVI-D and the HDMI are switched while [BACKUP INPUT MODE] is set to [1] and
switching to the backup input signal is possible.
f If [BACKUP INPUT MODE] is set to [2], the input is switched seamlessly when the inputs of SDI1 and SDI2 are switched while switching to
the backup input signal is possible.
f When [AUTOMATIC SWITCHING] is set to [ENABLE], and [BACKUP INPUT STATUS] is [ACTIVE], the signal is switched to the backup
input if the input signal is disrupted.
f When [AUTOMATIC SWITCHING] is set to [ENABLE] and the signal is automatically switched to the backup input due to disruption of the
input signal, [BACKUP INPUT STATUS] changes to [INACTIVE]. In this case, switching to the backup input signal is not possible until the
original input signal is restored. If the signal is automatically switched to the backup input, switching to the backup input signal becomes
possible when the original input signal is restored. In this case, the current input is retained.
f [BACKUP INPUT SETTING] cannot be set during P IN P. The backup operation is not performed either.
f [BACKUP INPUT SETTING] cannot be set when the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] → [HDMI/DVI-D] or [SDI1/
SDI2] is set to anything other than [OFF]. The backup operation is not performed either.
f [BACKUP INPUT SETTING] cannot be set when the [DISPLAY OPTION] menu → [SDI IN] → [SDI LINK] is set to [DUAL LINK] or [AUTO].
The backup operation is not performed either.
[SIMUL INPUT SETTING]
Set this function when the video signal in simultaneous format is input and used.
1)
Press as to select [SIMUL INPUT SETTING].
2)
Press the <ENTER> button.
f The [SIMUL INPUT SETTING] screen is displayed.
3)
Press as button to select [RGB1/RGB2], [HDMI/DVI-D], or [SDI1/SDI2].
4)
Press qw to switch the setting.
f The items will switch each time you press the button.
[OFF]
[AUTO(3D)]
[AUTO(2D)]
*1
*1 This can be set only when [SIMUL INPUT SETTING] is set to [HDMI/DVI-D] or [SDI1/SDI2].
Note
f If [AUTO(2D)] is set, 2D images are displayed when the same 2D compatible signals are entered to each input.
f If [AUTO(3D)] is set, 3D images are displayed when the same 3D compatible signals are entered to each input.
f [SIMUL INPUT SETTING] cannot be set during P IN P.
f [SIMUL INPUT SETTING] cannot be set when [BACKUP INPUT MODE] is set to anything other than [OFF].
f This may not function properly for some connected external devices.
f This may not function properly depending on the signal.
f Usage of each input signal is displayed in [RGB1] and [RGB2], in [HDMI] and [DVI-D], and in [SDI1] and [SDI2] of the [SIMUL INPUT
SETTING] screen when [AUTO(3D)] or [AUTO(2D)] is set.
[SIMUL INPUT SETTING]
[AUTO(3D)]
Chapter 4 Settings — [DISPLAY OPTION] menu
This is not used for simultaneous input.
Displays 3D images of the simultaneous format.
Displays 2D image of the simultaneous format.
Usage of the input signal
[LEFT INPUT]
[RIGHT INPUT]
Details
Uses the signal for the corresponding input as a signal for the left
eye image.
Uses the signal for the corresponding input as a signal for the right
eye image.
ENGLISH - 111
Advertisement
Table of Contents
