Mitsubishi Electric 800 Series Instruction Manual page 294

*1 The communication protocol affects which terminals can be used. For details, refer to the Instruction Manual (Communication) or the Instruction
Manual of each communication option.
 Input signal list
• Refer to the following table and set the parameters.
Signal
Setting
name
Pr.59 = "0" (initial value)
0 RL
Pr.59 ≠ "0"
Pr.270 = "1, 11"
Pr.59 = "0" (initial value)
1 RM
Pr.59 ≠ "0"
Pr.59 = "0" (initial value)
2 RH
Pr.59 ≠ "0"
Second function selection
3 RT
Pr.270 = "1, 11"
4 AU Terminal 4 input selection
5 JOG Jog operation selection (Available for the standard model only)
7 OH
External thermal relay input
15-speed selection (Combination with multi-speeds of RL, RM, and
8 REX
RH)
10 X10 Inverter run enable (FR-XC/FR-HC2/FR-CV connection)
12 X12 PU operation external interlock
14 X14 PID control valid
15 BRI Brake opening completion
16 X16 PU/External operation switchover (External operation with X16-ON) Pr.79, Pr.340
18 X18 V/F switchover (V/F control with X18-ON)
24 MRS Output stop
STP
25 Start self-holding selection
(STOP)
26 MC Control mode switchover
27 TL Torque limit selection
30 JOG2
37 X37 Traverse function selection
46 TRG Trace trigger input
47 TRC Trace sampling start/end
50 SQ Sequence start
51 X51 Fault clear
Forward rotation command (assignable to the STF terminal
60 STF
(Pr.178) only)
Reverse rotation command (assignable to the STR terminal
61 STR
(Pr.179) only)
62 RES Inverter reset
65 X65 PU/NET operation switchover (PU operation with X65-ON)
66 X66 External/NET operation switchover (NET operation with X66-ON)
Command source switchover (command by Pr.338 or Pr.339
67 X67
enabled with X67-ON)
72 X72 PID P control switchover
92 X92 Emergency stop
9999 - No function
*1 When Pr.59 Remote function selection ≠ "0", functions of the RL, RM, and RH signals are changed as shown in the table.
*2 When Pr.270 Stop-on-contact control selection = "1 or 11", functions of the RL and RT signals are changed as shown in the table.
*3 The OH signal is activated when the relay contact is open.
Function
Low-speed operation command
*1
Remote setting (setting clear)
*2
Stop-on-contact selection 0
Middle-speed operation
command
*1
Remote setting (deceleration)
High-speed operation command
*1
Remote setting (acceleration)
*2
Stop-on-contact selection 1
*3
Related parameter
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.270, Pr.275, Pr.276
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.44 to Pr.48, Pr.51, Pr.450
to Pr.463, Pr.569, Pr.832,
Pr.836, etc.
Pr.270, Pr.275, Pr.276
Pr.267
Pr.15, Pr.16
Pr.9
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.17, Pr.30, Pr.70
Pr.79
Pr.127 to Pr.134, Pr.575 to
Pr.577
Pr.278 to Pr.283
Pr.80, Pr.81, Pr.800
Pr.17
Pr.250
Pr.800
Pr.815
Pr.15, Pr.16
Pr.592 to Pr.597
Pr.1020 to Pr.1047
Pr.1020 to Pr.1047
Pr.414
Pr.414
Pr.250
Pr.250
Pr.75
Pr.79, Pr.340
Pr.79, Pr.340
Pr.338, Pr.339
Pr.127 to Pr.134, Pr.575 to
Pr.577
Pr.1103
—
12.(T) Multi-Function Input Terminal Parameters
12.6 Input terminal function selection
11
12
Refer to
page
202
13
171
334
202
14
171
202
15
171
298
16
334
274
200
17
206
202
18
396
180
339
19
330
180
88
296
20
300
88
102
200
337
377
377
373
373
300
300
131
180
180
191
339
164
—
293