Mitsubishi Electric 800 Series Instruction Manual page 240

Increment
Monitor item
and unit
32-bit cumulative
1 kWh
energy (lower 16 bits)
32-bit cumulative
1 kWh
energy (upper 16 bits)
32-bit cumulative
0.01 kWh
energy (lower 16 bits)
32-bit cumulative
0.01 kWh
energy (upper 16 bits)
BACnet valid APDU
counter 1
PID manipulated
0.1%
amount
Dancer main set
*15
0.01 Hz
speed
*1 The monitor code is used for the Mitsubishi inverter protocol, CC-Link, CC-Link IE TSN, and CC-Link IE Field Network Basic.
*2 The monitor code is used for the MODBUS RTU, MODBUS/TCP, and BACnet/IP.
*3 Indication with a minus sign is not possible via RS-485 communication (Mitsubishi inverter protocol or MODBUS RTU).
*4 To monitor the item on the LCD operation panel (FR-LU08) in the monitor mode, use Pr.774 to Pr.776 or the monitor function of the FR-LU08 for
setting.
*5 The cumulative energization time and actual operation time are accumulated from 0 to 65535 hours, then cleared, and accumulated again from 0.
*6 The actual operation time does not increase if the cumulative running time before power OFF is less than an hour.
*7 Since each readout of the output voltage and output current displayed on the operation panel is a 4-digit number, a value of more than "9999" is
displayed as "----".
*8 The inverter regards the output current which is less than the specified current level (5% of the rated inverter current) as 0 A. Therefore, each
readout of an output current and output power may show "0" if a too small-capacity motor is used as contrasted with the inverter capacity and the
output current falls below the specified value.
*9 Available when the plug-in option is connected.
*10 The details of bits for the input terminal status are as follows. (1: ON state, 0: OFF state of a terminal on the inverter. "—" denotes an indefinite
(null) value.)
b15 Standard model
- - -
b15 Ethernet model
- - -
b15 Safety communication model
- - -
*11 The details of bits for the output terminal status are as follows. (1: ON state, 0: OFF state of a terminal on the inverter. "—" denotes an indefinite
(null) value.)
b15 Standard model
- - -
b15 Ethernet model
- - -
b15 Safety communication model
- - -
*12 The details of bits for the option input terminal status 1 are as follows. (1: ON state, 0: OFF state of a terminal on the FR-A8AX.) Every bit is 0
(OFF) when the option is not installed.
b15
X15 X14 X13
*13 The details of bits for the option input terminal status 2 are as follows. (1: ON state, 0: OFF state of a terminal on the FR-A8AX. "—" denotes an
indefinite (null) value.) Every bit is 0 (OFF) when the option is not installed.
b15
- - -
*14 The details of bits for the option output terminal status are as follows. (1: ON state, 0: OFF state of a terminal on the FR-A8AY/A8AR. "—" denotes
an indefinite (null) value.) Every bit is 0 (OFF) when the option is not installed.
b15
- - -
*15 The increment varies depending on the Pr.53 setting. (Refer to
*16 The monitored values are retained even if an inverter fault occurs. Resetting clears the retained values.
Communication
Pr.
Monitor Monitor
setting
*1 *2
code 1 code 2
— H4D 40277
— H4E 40278
— H4F 40279
— H50 40280
83 H53 40283
91 H5B 40291
97 H61 40297
- - RES - MRS
- - - -
- -
- -
- - - -
- - - -
- - - -
X12 X11 X10 X9
- - - -
- - - RA3
Negative
indication
*3
(-)
The upper or lower 16 bits of the 32-bit cumulative
energy is displayed on each indication.
Monitoring via communication is available.
The count of valid APDU detection is displayed.
(Available only for the FR-E800-EPA and FR-E800-
SCEPA.)
The PID control manipulated amount is displayed.
○
(Refer to page 348.)
The set speed for main speed during the dancer control
operation is displayed.
- RH RM
- - - -
- - - -
-
- SO ABC
- SO - ABC
- - - ABC
X8 X7 X6 X5
- - - -
RA2 RA1 Y6 Y5
page 234).
11.(M) Item and Output Signal for Monitoring
11.2 Monitor item selection on operation panel or via communication
Description
RL - - STR STF
- - - DI1 DI0
- - - -
- - -
FU RUN
- - - -
- - - -
X4 X3 X2 X1
- - - -
Y4 Y3 Y2 Y1
11
12
13
14
15
16
17
18
19
b0
b0
20
b0
-
b0
b0
-
b0
-
b0
X0
b0
DY
b0
Y0
239