Skoda Octavia III 2013 Workshop Manual

Skoda Octavia III 2013 Workshop Manual

Hide thumbs Also See for Octavia III 2013:
Table of Contents

Advertisement

Quick Links

Service
Workshop Manual
Octavia III 2013 ➤
Octavia III 2014 ➤
Electrical system
Edition 12.2014
Service Department. Technical Information

Advertisement

Table of Contents
loading

Summary of Contents for Skoda Octavia III 2013

  • Page 1 Service Workshop Manual Octavia III 2013 ➤ Octavia III 2014 ➤ Electrical system Edition 12.2014 Service Department. Technical Information...
  • Page 2 Service List of Workshop Manual Repair GroupsList of Workshop Manual Repair GroupsList of Workshop Manual Repair Groups R e p a i r G r o u p 27 - Starter, current supply, CCS 90 - Gauges, instruments 91 - Communication 92 - Windscreen wash/wipe system 94 - Lights, bulbs, switches - exterior 96 - Lights, bulbs, switches - interior...
  • Page 3: Table Of Contents

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Contents 27 - Starter, current supply, CCS ........
  • Page 4 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Infotainment summary of components – with navigation ......
  • Page 5 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Windscreen wiper and washer system ........
  • Page 6 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Summary of components of steering column switch with mechanical ignition/starter switch ............... . 117...
  • Page 7 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing the passenger side glove box light switch ....156...
  • Page 8 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Contents...
  • Page 9: Starter, Current Supply, Ccs

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 27 – Starter, current supply, CCS Contact corrosion (SRL000764; Edition 12.2014) The use of unsuitable connection elements (screws, nuts, wash‐ ers, …) causes contact corrosion. This is why only connection elements with a special surface coat‐...
  • Page 10: Battery

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Battery WARNING When working on the battery, wear proper protection and ob‐ serve safety precautions (see “Electrical System – General notes” ⇒ Electrical System – General notes; Rep. gr. 27 ).
  • Page 11 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Open cover -1-, loosen nut -3- and disconnect battery earth strap -2- only. Note If both terminals are disconnected, only then disconnect pole ter‐ minal (-) from battery earth.
  • Page 12: Checking Battery

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Vehicles with battery monitoring control unit - J367- (with start/ stop system and auxiliary heating and additional heating) – Disconnect the plug -2- from the control unit -3- before con‐...
  • Page 13: Removing And Installing Battery

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing battery WARNING Observe the battery handling instructions as well as the warn‐ ing instructions and safety precautions for lead acid batteries ⇒ “2.2 Warning instructions and safety precautions when work‐...
  • Page 14: Removing And Installing Battery Tray

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Insert battery into the battery tray -1- so that the battery base is resting against the rear and the sides -arrows- up to the stop.
  • Page 15: Battery Parameterisation

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Battery parameterisation This is performed only on vehicles with a battery monitoring con‐ trol unit - J367- when replacing the battery with a new one of another type or with higher capacity.
  • Page 16: Starter

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Starter ⇒ “3.1 Removing and installing starter”, page 8 Removing and installing starter Removing – Disconnect battery earth strap ⇒ “2.3.1 Disconnecting battery”, page 2 – Remove air filter housing in front of the battery (does not apply to 1.2 TSI;...
  • Page 17 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unscrew nut -1- (23 Nm) and lay aside line holder -2- together with line. All vehicles: – Screw out bottom fixing screw -arrow- and remove the starter.
  • Page 18: Generator

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Generator ⇒ “4.1 Checking generator”, page 10 ⇒ “4.2 Removing and installing alternator”, page 10 ⇒ “4.3 Fixing the B+ wire to the AC generator”, page 12 ⇒...
  • Page 19 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – 1.8 TSI engine – Loosen hose clamps -2-, unscrew screws -arrows- and remove air flow hose. Note Close open lines with clean plug for example from the blanking plug set -VAS 6122- .
  • Page 20: Fixing The B+ Wire To The Ac Generator

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Vehicles with AC generator secured from the side – screw out screws -arrows- (23 Nm). – Remove AC generator downwards. Installing Installation is carried out in the reverse order. When installing,...
  • Page 21: Checking The Carbon Brushes Of The Ac Generator

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Note Always use a new self-locking nut for attaching the B+ cable -arrow-, see ⇒ Electronic Catalogue of Original Parts . The tightening torque for the self-locking nut of the B+ cable -arrow- is 20 Nm.
  • Page 22: Removing And Installing The Valeo Voltage Regulator

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing the Valeo volt‐ age regulator – Press off screen cap on the rear side of the generator -arrows-. – Unscrew screws -1- and nut -2-.
  • Page 23: Removing And Installing The V-Ribbed Belt Pulley With Free Wheel

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing the V-ribbed belt pulley with free wheel Special tools and workshop equipment required ♦ Polygon-head adapter - MP 1-309- – Remove ribbed V-belt and/or generator ⇒...
  • Page 24: Start-Stop" System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 “Start-stop” system ⇒ “5.1 Safety precautions for vehicles with start-stop system”, page 16 ⇒ “5.2 General description”, page 16 ⇒ “5.3 Fault recognition and fault display”, page 17 ⇒...
  • Page 25: Fault Recognition And Fault Display

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Fault recognition and fault display For fault finding use the ⇒ Vehicle diagnostic tester in the function “Targeted fault finding”. Battery recharging or starting by exter‐...
  • Page 26: Button For "Start-Stop" System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Note After replacing, adapt (code) the new battery monitoring control unit - J367- with ⇒ Vehicle diagnostic tester. Button for “start-stop” system Removing and installing the button for the start-stop system ⇒...
  • Page 27: Cruise Control System (Ccs)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Cruise control system (CCS) The engine control unit controls the function of the CC on vehicles which have a cruise control. Fault recognition and fault display Faults of the CC are transmitted via the engine control unit.
  • Page 28: Automatic Distance Control (Adapted Cc) And Front Assist

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Automatic distance control (adapted CC) and Front Assist ⇒ “7.1 General description”, page 20 ⇒ “7.2 Overview of the fitting positions: Automatic distance con‐ trol, Front Assist”, page 20 ⇒...
  • Page 29 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Dash panel insert ❑ with control unit in dash panel insert - J285- 2 - Switch unit on the steering column ❑ Equipment variant with adaptive CCS ❑...
  • Page 30: Removing And Installing The Clearance Control Control Unit J428

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing the clearance control control unit - J428- Note When replacing the Clearance control control unit - J428- , con‐ nect ⇒ Vehicle diagnostic tester and, in the operating mode “Targeted fault finding”...
  • Page 31: Calibrate Automatic Distance Control

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unlock quick-release fittings -2- by rotating it -arrow-. – Remove quick-release fittings -2- from the pin bolts -1-. – Remove retaining plate -3- from the control unit -4-.
  • Page 32: Gauges, Instruments

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 90 – Gauges, instruments Dash panel insert ⇒ “1.1 General description”, page 24 ⇒ “1.2 Adjust/replace dash panel insert”, page 24 ⇒ “1.3 Removing and installing dash panel insert”, page 24 ⇒...
  • Page 33 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing – Switch off the ignition and all electrical components. – Pull steering wheel out fully and lock it in its lowest position. – Take hold of the bottom cover of the control panel -1- and un‐...
  • Page 34: Warning Lights In The Dash Panel Insert

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Warning lights in the dash panel insert Note ♦ Detailed description of the function of warning lights ⇒ Owner's manual Octavia III . The arrangement and number of warning lights depends on the equipment level and type of dash panel ♦...
  • Page 35: The Self-Diagnostic Function Of The Dash Panel Insert

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 5 - Exhaust gas control system 6 - Trailer indicator light 7 - Warning light for stability (ESC) 8 - Antilock braking system (ABS) 9 - Main beam assist...
  • Page 36: Communication

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 91 – Communication Multimedia information system – In‐ fotainment ⇒ “1.1 General points”, page 28 ⇒ “1.2 Installation – Infotainment system”, page 29 ⇒ “1.3 Infotainment summary of components – with radio”, page 31 ⇒...
  • Page 37: Installation - Infotainment System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Installation – Infotainment system ⇒ “1.2.1 Basic Infotainment features (entry)”, page 29 ⇒ “1.2.2 Medium Infotainment features (standard)”, page 30 ⇒ “1.2.3 High Infotainment features (high)”, page 30 1.2.1...
  • Page 38 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1.2.2 Medium Infotainment features (stand‐ ard) Bolero, Amundsen installation Display unit Control unit Bolero ♦ Capacitive colour touch display ♦ CD drive; SD card slot ♦ Media inputs – AUX-IN points; USB/MEDIA IN (Mitsumi) ♦...
  • Page 39: Infotainment Summary Of Components - With Radio

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Infotainment summary of components – with radio The number and the design of the components depend on the vehicle equipment. 1 - Front treble speaker ❑ Removing and installing ⇒...
  • Page 40: Infotainment Summary Of Components - With Navigation

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Infotainment summary of components – with navigation The number and the design of the components depend on the vehicle equipment. 1 - Front treble speaker ❑ Removing and installing ⇒...
  • Page 41: Electronic Anti-Theft Coding

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Electronic anti-theft coding The Infotainment display/control unit is equipped with an elec‐ tronic comfort anti-theft coding, which operates in combination with the dash panel insert. The Infotainment display/control unit must be paired with an ap‐...
  • Page 42 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Compress plug catch -arrows-. – Open catch clamp -arrow- and disconnect plug. – Release and pull off other plug connections. – Press back catches from the side and remove the unlocking tools.
  • Page 43 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove the display unit by pulling on the unlocking tools -arrows-. – Release and disconnect the plug connections. – Press back catches from the side and remove the unlocking tools.
  • Page 44: Infotainment Self-Diagnosis

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Compress plug catch -arrows-. – Open catch clamp -arrow- and disconnect plug. – Release and pull off other plug connections. Installing Installation is carried out in the reverse order. When installing,...
  • Page 45: Aerial Systems

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Aerial systems ⇒ “2.1 Overview of the aerial systems”, page 37 ⇒ “2.2 Removing and installing the roof aerial”, page 39 ⇒ “2.3 Removing and installing frequency filters for frequency modulation (FM) in the positive cable R179 ”, page 40...
  • Page 46 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Induction plate ❑ Forms the GSM signal induction field ❑ Removing and installing ⇒ “3.4 Removing and in‐ stalling induction plate”, page 45 2 - Signal amplifier for mobile phones ❑...
  • Page 47: Removing And Installing The Roof Aerial

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 2.1.2 Octavia Combi 1 - Induction plate ❑ Forms the GSM signal induction field ❑ Removing and installing ⇒ “3.4 Removing and in‐ stalling induction plate”,...
  • Page 48: Removing And Installing Frequency Filters For Frequency Modulation (Fm) In The Positive Cable R179

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 For vehicles with panoramic roof: – Unhook headlining ⇒ Body Work ; Rep. gr. 70 . Continued for all vehicles: – Release and disconnect plug connections -1- to the aerial ca‐...
  • Page 49: Removing And Installing Am/Fm, Fm2/Dab Aerial Module (Amplifier)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing AM/FM, FM2/ DAB aerial module (amplifier) Note The work sequence for removing and installing is similar for ♦ the two amplifiers. Arrangement of the amplifier ♦...
  • Page 50: Replacing Aerial Cables

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Replacing aerial cables Note ♦ Aerial cables must not be repaired, but replaced with a new original part see ⇒ Electronic Catalogue of Original Parts ;...
  • Page 51: Telephone System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Telephone system ⇒ “3.1 General Instructions”, page 43 ⇒ “3.2 Summary of components – telephone system”, page 43 ⇒ “3.3 Removing and installing the aerial signal reception ampli‐...
  • Page 52: Removing And Installing The Aerial Signal Reception Amplifier (Compensor)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Telephone microphone - R38- ❑ in the front interior light ❑ Removing and installing ⇒ “3.6 Removing and in‐ stalling the microphone for the telephone R38 ”,...
  • Page 53: Removing And Installing Induction Plate

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Octavia Octavia Combi – Disconnect plug and remove amplifier -1-. – Installation is carried out in the reverse order. Removing and installing induction plate – Remove storage compartment in the front centre console ⇒...
  • Page 54: Removing And Installing The Microphone For The Telephone R38

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Measure the resistance between the contacts -arrows- under‐ neath the washer with multimeter. Measured values: • 10 kΩ - induction plate OK. • 20 kΩ - short circuit in the aerial •...
  • Page 55: Multi-Functional Steering Wheel

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Multi-functional steering wheel ⇒ “4.1 General description”, page 47 ⇒ “4.2 Removing and installing the Infotainment switch units”, page 47 ⇒ “4.3 Removing and installing switch units for gearbox operation in Tiptronic mode (gearbox 02E, 0AM –...
  • Page 56: Removing And Installing Switch Units For Gearbox Operation In Tiptronic Mode (Gearbox 02E, 0Am - Dsg)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove bolts -3- (0.4 Nm). – When removing modules -1- and -2-, carefully loosen the con‐ nection cable from the bracket -arrows-. – Vehicles with automatic transmission with column gear shift –...
  • Page 57: Self-Diagnosis Of The Multi-Functional Steering Wheel

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unscrew screw -arrow A- (1.7 Nm), swivel out switch unit for gearbox operation -1- -arrow B- and remove. Installing Installation is carried out in the reverse order. When installing,...
  • Page 58: Canton Sound System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Canton sound system ⇒ “5.1 Fitting position overview – sound system components”, page 50 ⇒ “5.2 Removing and installing the sound system control unit”, page 51 ⇒...
  • Page 59: Removing And Installing The Sound System Control Unit

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing the sound sys‐ tem control unit Removing – Switch off all electrical components and take out the ignition key. – Push the left front seat completely towards the rear and the highest point.
  • Page 60: Removing And Installing Loudspeakers

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing loudspeak‐ ⇒ “6.1 Removing and installing the front and rear mid-bass speak‐ er”, page 52 ⇒ “6.2 Removing and installing front treble loudspeakers”, page 52 ⇒...
  • Page 61: Removing And Installing Subwoofer

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Screw out the screw -arrows- (0.3 Nm) and remove the loud‐ speaker. – Installation is carried out in the reverse sequence. Removing and installing subwoofer –...
  • Page 62: Connections For Audio/Video Signal Media In (Multimedia Socket) External Source

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Connections for audio/video signal MEDIA IN (multimedia socket) exter‐ nal source ⇒ “7.1 Removing and installing connections for audio/video signal external source”, page 54 Removing and installing connections for audio/video signal external source Connections for the audio/video signal external source are loca‐...
  • Page 63 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unlock the plugs from the USB connection -3- from the top and remove. – Insert a small screwdriver into the middle of the plug at an angle from below, unlock by pressing together, and remove the plugs from the connection for external audio sources Pos.
  • Page 64: Smartgate System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 SmartGate system ⇒ “8.1 General points”, page 56 ⇒ “8.2 SmartGate system - check the correct function”, page 57 ⇒ “8.3 Remove and install control unit for information electronics 2 J829 (SmartGate)”, page 58...
  • Page 65: Smartgate System - Check The Correct Function

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 SmartGate system - check the correct function Caution Correct communication within the scope of the SmartGate sys‐ tem relies on the customer's communications equipment (e.g., cell phone/tablet) functioning correctly, and on the software applications being installed.
  • Page 66: Remove And Install Control Unit For Information Electronics 2 J829 (Smartgate)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Connection problems If the connection fails, then check the following points. ♦ Are the conditions for a successful connection fulfilled? ♦ Does SmartGate show up in the list of available Wi-Fi net‐...
  • Page 67: Set The Parameters For The Wi-Fi Connection

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove the perforated floor covering and the control unit -1- from the Velcro fastener and, taking the lengths of the con‐ nected cables into consideration, remove the unit.
  • Page 68: Update Firmware

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Gate is reset to the factory default settings and transmission encryption is set to WPA2. After re-connecting the battery earth strap, switch on the ignition and enter the vehicle identification number (in uppercase) as the PIN code.
  • Page 69 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Note During the update process, the LED display on the control unit ♦ for information electronics 2 - -J829-- lights up orange (red and green at the same time).
  • Page 70: Windscreen Wash/Wipe System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 92 – Windscreen wash/wipe system Windscreen and rear window wiper system ⇒ “1.1 Removing and installing the washer pump and washer fluid reservoir”, page 62 ⇒ “1.2 Removing and installing the spray nozzles for windscreen washer system”, page 63...
  • Page 71: Removing And Installing The Spray Nozzles For Windscreen Washer System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove expansion clip -1- and push filler neck -3- with filler pipe -4- out of the bracket -2-. – Screw out nut -arrow- (8 Nm).
  • Page 72: Removing And Installing The Spray Nozzle For Rear Window Washer System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove the cooling water tank cover ⇒ Body Work; Rep. gr. 66 . – Carefully lever the angled pieces off the spray nozzles from below and disconnect the plug connections (of the heated nozzles).
  • Page 73: Repairing Washer Fluid Level Pipes

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1.3.3 Octavia Combi GreenLine The nozzle is protected against dirt and is part of the spoiler. The nozzle cannot be used separately. Repairing washer fluid level pipes All the notes and comments to this chapter can be found in the Workshop Manual ⇒...
  • Page 74: Headlamp Cleaning System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Headlamp cleaning system ⇒ “2.1 Removing and installing headlight cleaning system pump V11 ”, page 66 ⇒ “2.2 Removing and installing the lift cylinder for spray nozzles of headlight”, page 66...
  • Page 75: Bleed The Headlamp Cleaning System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Bleed the headlamp cleaning system After installation or when it is first put into service the headlamp cleaning system must be bled, in order to guarantee a perfect operation.
  • Page 76: Windscreen Wiper And Washer System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Windscreen wiper and washer sys‐ ⇒ “3.1 Fault recognition and fault display, coding”, page 68 ⇒ “3.2 Removing and installing the wiper arms with wiper blades and setting their final setting”, page 68...
  • Page 77 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unscrew the nuts -2- by a few turns. – Push the extractor for wiper arms -T10369/1- , as shown, onto the arm. Note To release the wiper arm, always use the thrust piece -2- in order to avoid damage to the thread of the wiper motor shaft.
  • Page 78: Removing And Installing Wiper Motor With Linkage

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Insert windscreen wiper arms with wiper blades and align wip‐ er blades to the markings in the windscreen -1-. – Slightly tighten fixing nuts. – Operate the flick wipe and check again or correct the setting of the wiper arms.
  • Page 79: Removing And Installing Sensor For Rain And Light Detection G397

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing Sensor for rain and light detection - G397- Caution If the sensor for rain and light detection - G397- is removed from the retaining plate on the windscreen (e.g. when changing the windscreen), it can be subsequently installed again.
  • Page 80 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Carefully lever the sensor for rain and light detection - G397- Pos. -2- out of the retaining frame from above starting from the front windscreen.
  • Page 81: Repairing The Rain And Light Detector Sensor G397 , Valeo Manufacturer

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Repairing the rain and light detector sensor - G397- , Valeo manufacturer Note There are various bushings for the Rain and light detector ♦ sensor - G397- from different manufacturers.
  • Page 82 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Press the cushion onto the sensor -2- through the transparent foil -1-, so that there are no bubbles between the foil and sen‐ sor. – Carefully pull the transparent protective foil -1- off the cushion -2-.
  • Page 83: Rear Window Wiper System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Rear window wiper system ⇒ “4.1 Removing and installing the wiper arm with wiper blade and setting its final setting”, page 75 ⇒ “4.2 Removing and installing rear window wiper motor”,...
  • Page 84: Removing And Installing Rear Window Wiper Motor

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Set final position of wiper arm in accordance with the figure. The value -a- is: • Octavia - 52±2 mm • Octavia Combi - 45±2 –...
  • Page 85 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Recess in the rear window implementation -arrow- is located at the top, from the outside, see Fig. 4. Rear window wiper system...
  • Page 86: Lights, Bulbs, Switches - Exterior

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 94 – Lights, bulbs, switches - exterior Headlights – halogen headlights ⇒ “1.1 Summary of components of headlight”, page 78 ⇒ “1.2 Removing and installing headlight”, page 80 ⇒...
  • Page 87 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Headlight housing ❑ Removing and installing ⇒ “1.2 Removing and in‐ stalling headlight”, page 80 ❑ adjust ⇒ “1.3 Adjusting head‐ lights”, page 80...
  • Page 88: Removing And Installing Headlight

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing headlight Removing Note The removal and installation will be demonstrated using the ex‐ ample of the left-hand headlight. The removal and installation of the right headlight follows the same principle.
  • Page 89: Replacing Light Bulbs In Headlights

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Replacing light bulbs in headlights ⇒ “1.4.1 Replacing H7 bulb for low beam light”, page 81 ⇒ “1.4.2 Replacing the multifunctional bulb H15 (for main beam light, daytime running light, side light)”, page 82...
  • Page 90 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1.4.2 Replacing the multifunctional bulb H15 (for main beam light, daytime running light, side light) WARNING The H15 light bulb is pressurized and can burst when changing the bulb.
  • Page 91: Replace Headlight Fixing Brackets

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Switch off the ignition and all electrical components. – Remove the headlight with the defective light bulb ⇒ “1.2 Removing and installing headlight”, page 80 –...
  • Page 92: Change Headlight For Right-Hand And/Or Left-Hand Traffic

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Insert a new bracket true to form -arrows-. Note The attachment brackets as spare parts do not have openings for fixing screws. – Insert the fixing screws directly into the bracket and tighten (1.5 Nm).
  • Page 93: Removing And Installing Headlight Range Control Motor

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Right-hand drive: – Forcefully press on the middle area of the foil -B-. – Carefully pull off the auxiliary part of the foil -A- from the head‐...
  • Page 94 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Move the control motor -1- in the direction of arrow -A-, undo the pressure element from the groove, and remove in the di‐ rection of arrow -B-.
  • Page 95: Headlights - Bi-Xenon Headlights

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Headlights – Bi-xenon headlights ⇒ “2.1 General description”, page 87 ⇒ “2.2 Assembly overview - Bi-xenon headlights”, page 88 ⇒ “2.3 Summary of components – Bi-xenon headlights with LED module”, page 90...
  • Page 96: Assembly Overview - Bi-Xenon Headlights

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 ♦ Signals of vehicle level sensors on front and rear axle ♦ individual wheel speeds ♦ Position of the light switch On the basis of this information, it controls the rotary and inclina‐...
  • Page 97 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 6 - Gas discharge lamp with integrated ignition coil ❑ 42V, 35 W (type D3S) ❑ Renew ⇒ “2.5.4 Replacing the gas discharge lamp ”, page 93...
  • Page 98: Summary Of Components - Bi-Xenon Headlights With Led Module

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Summary of components – Bi-xenon headlights with LED module Note ♦ LED module is defined for side light and daytime running light. The LED module is integrated into the headlight housing and cannot be changed separately.
  • Page 99: Removing And Installing Headlight

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 12 - Control unit for daylight driving light and side light - J860- (LED module) left or -J861- right ❑ Removing and installing ⇒ “2.11 Removing and installing Control unit for daylight driving light and side light J860 (LED module) left and J861 right”, page 95...
  • Page 100 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Take hold of bulb socket -1- and remove it while observing the connected cable lengths -arrow-. – Remove bulb -2- from holder -1-. – After replacing the bulb, press socket and bulb fully into the headlight and install cover.
  • Page 101 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Turn socket with bulb -1- -arrow- and remove. – Replace defective light bulb. – Installation is carried out in the reverse sequence. 2.5.3 Replacing bulb PYW24Y for the turn sig‐...
  • Page 102: Change Headlight For Right-Hand / Left-Hand Traffic

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Press the peg at the plug for unlocking and remove the plug -2- towards the bottom. – Turn gas discharge lamp by approx. 45° -arrow- and remove from the headlight housing.
  • Page 103: Remove And Install Performance Module For The Headlight J667 Left Or J668 Right

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 2.10 Remove and install performance mod‐ ule for the headlight - J667- left or -J668- right Removing – Remove headlight ⇒ “1.2 Removing and installing headlight”, page 80 –...
  • Page 104 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Note If the control unit is replaced, ⇒ Vehicle diagnostic tester connect and, in the operating mode “Targeted fault finding”, select the “Replace control unit” function of the relevant control unit.
  • Page 105: Vehicle Level Sensor G78 Front Left Or G76 Rear Left

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unplug connector -3-. – Remove expanding rivets -2- and remove unit -1-. Install Installation is carried out in the reverse order. 2.13 Vehicle level sensor - G78- front left or -...
  • Page 106 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – To access the fixing screw, carefully knock out and remove the plug -arrow-. – To be able to see the headlight range control motor better,...
  • Page 107: Lights In The Exterior Mirror

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Lights in the exterior mirror ⇒ “3.1 Side turn signal lights”, page 99 ⇒ “3.2 Door entry lighting”, page 100 Side turn signal lights Removing – Switch off the ignition and all electrical components.
  • Page 108: Door Entry Lighting

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Press off the catches -arrow A- and slightly lower the cover -1-. – Loosen bottom cover -1- by pushing it out of the catch -arrow B-.
  • Page 109 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unscrew screws -arrows A-. – Press off the catches -arrow B- and remove cover -1-. – Remove socket with bulb -1-. – Replace defective light bulb (W5W) if necessary.
  • Page 110: Tail Lights

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Tail lights ⇒ “4.1 Removing and installing tail light”, page 102 ⇒ “4.2 Replacing the light bulbs of the tail light”, page 103 Removing and installing tail light Special tools and workshop equipment required ♦...
  • Page 111: Replacing The Light Bulbs Of The Tail Light

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Replacing the light bulbs of the tail light ⇒ “4.2.1 Tail light - Octavia”, page 103 ⇒ “4.2.2 Tail light with LED diodes - Octavia”, page 103 ⇒...
  • Page 112 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Note The LED module is integrated into the lamp and cannot be changed separately. – Remove bolts -arrows-. – Remove bulb carrier. Summary of components of light bulbs:...
  • Page 113 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 4.2.4 Tail light with LED diodes - Octavia Combi – Remove tail light ⇒ “4.1 Removing and installing tail light”, page 102 Note The LED module is integrated into the lamp and cannot be changed separately.
  • Page 114: Fog Lights, Fog Lights With The "Corner" Function

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Fog lights, fog lights with the “Corner” function ⇒ “5.1 General description, fault recognition and fault display”, page 106 ⇒ “5.2 Removing and installing fog light”, page 107 ⇒...
  • Page 115: Removing And Installing Fog Light

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing fog light Removing (except for Octavia RS and Scout) – Octavia - For example, insert a hook into the opening in the grid -top arrow- in order to remove the wheel trim cap (tool kit) and unclip the grid -1- from the catches in sequence and take out.
  • Page 116: Adjusting Fog Lights

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unclip the cover -1- over the fog light. – Screw out the screws -arrows- (1.5 Nm) and remove the fog light -2-. – Disconnect plug.
  • Page 117 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Using a small screwdriver, carefully unlock the catch -arrow A- and remove the lens -1- -arrow B-. All vehicles: – Turn socket with lamp in -direction of arrow- and remove.
  • Page 118: Additional Brake Light

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Additional brake light ⇒ “6.1 Removing and installing the high level brake light - Octa‐ via”, page 110 ⇒ “6.2 Removing and installing the high level brake light - Octavia Combi”, page 111...
  • Page 119: Removing And Installing The High Level Brake Light - Octavia Combi

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing the high level brake light - Octavia Combi Note The high level brake light is fitted with LEDs which cannot be re‐ placed individually.
  • Page 120: Removing And Installing The High Level Brake Light - Octavia Combi Greenline

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Connect the metal clamps -2- back onto the brake light. Note The metal clamps -2- must be fitted in such a way that the pegs...
  • Page 121 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Cover caps 2 - Bolts ❑ 2.5 ± 0.5 Nm 3 - Spoiler 4 - Connector with foam rubber 5 - Rubber grommet 6 - Brake lights Removing –...
  • Page 122 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Note Three seal variants are possible. ♦ Self-adhesive foil or a plastic cap -2- is used in some vehicles ♦ instead of the plastic caps -3-.
  • Page 123 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Tilt out the brake light -2- slightly in the direction of arrow -A- and remove from the spoiler in direction of arrow -B-, taking connected wiring lengths into consideration.
  • Page 124: Registration Number Lighting

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Registration number lighting ⇒ “7.1 Removing and installing registration number lighting”, page ⇒ “7.2 Replacing bulb for the number plate light”, page 116 Removing and installing registration...
  • Page 125: Steering Column Switch

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Steering column switch ⇒ “8.1 Summary of components of steering column switch with mechanical ignition/starter switch”, page 117 ⇒ “8.2 Summary of components of steering column switch with control unit for electronic steering column lock J764 ”,...
  • Page 126: Summary Of Components Of Steering Column Switch With Control Unit For Electronic Steering Column Lock J764

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 8 - Switch unit on the steering column ❑ with turn signal light switch - E2- and wiper switch for intermittent operation - E22- ❑ Equipment variant with cruise control system: with CCS switch - E45- ❑...
  • Page 127: Removing And Installing Switch Unit On The Steering Column

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 7 - Transport security 8 - Screw ❑ 1.1 Nm 9 - Switch unit on the steering column ❑ with turn signal light switch - E2- and wiper switch for intermittent operation - E22- ❑...
  • Page 128: Removing And Installing Steering Column Electronics Control Unit J527

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Screw out the screw -2- (1.1 Nm) and push the switch unit -1- out of the bracket on the steering lock. Installing Installation is carried out in the reverse order. When installing, observe the following: –...
  • Page 129: Setting The Correct Installation Position Of The Restoring Ring With Coil Spring

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Pull out plug fuse -4-, push unlocking down and disconnect plug connection -3-. WARNING Risk of destruction of electronic components by static dis‐ charge. Prior to disconnecting the electrical plug connection the me‐...
  • Page 130: Contact Assignment On The Steering Column Electronics Control Unit J527

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Slowly turn the ring rotor -3- manually to the left up to the stop. – Turn ring rotor clockwise manually by approximately 3.5 rev‐ olutions so that: •...
  • Page 131: Steering Lock With Ignition Starter Switch And Lock Cylinder

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Steering lock with ignition starter switch and lock cylinder ⇒ “9.1 Removing and installing lock cylinder”, page 123 ⇒ “9.2 Removing and installing steering lock housing”, page 124 ⇒...
  • Page 132: Removing And Installing Steering Lock Housing

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Lead steel cable -2- (about 1.2 mm in diameter) through the hole in the ignition key -arrow-. – This unlocks the fuse -3- and the lock cylinder -1- can be pulled out of the steering lock.
  • Page 133: Removing And Installing The Elv J764

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Tighten new screws -arrows- until the screw heads have been broken off. Removing and installing the ELV - J764- Note If the control unit is replaced, select the “replace control unit”...
  • Page 134: Removing And Installing Ignition/Starter Switch

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing ignition/starter switch Removing Note The steering wheel must not be removed. For installing the fixing screws of the bottom trim panel for steering column, turn the steering wheel to the left by 90°...
  • Page 135 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing Note The steering wheel must not be removed. For installing the fixing screws of the bottom trim panel for steering column, turn the steering wheel to the left by 90° and subsequently turn it to the right.
  • Page 136: Keyless Unlocking Of The Vehicle/The Steering, Keyless Start/Stop - Kessy System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Keyless unlocking of the vehicle/the steering, keyless start/stop – KESSY system ⇒ “10.1 General description”, page 128 ⇒ “10.2 Fault recognition and fault display”, page 128 ⇒...
  • Page 137 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Aerial ❑ under the rear bumper ❑ Removing and installing ⇒ “10.5.5 Removing and installing the rear aerial in the middle”, page 132 2 - Aerial ❑...
  • Page 138: Access And Start Authorisation Control Unit J965

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Other components with which the KESSY system communicates via the CAN bus ♦ Vehicle voltage control unit - J519- ♦ Data bus diagnostic interface Gateway - J533- ♦...
  • Page 139 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove the centre console ⇒ Body Work; Rep. gr. 68 . – Using the disassembly tool (e.g. -MP8-602/1- ) lever the aerial -1- out of the holder -2- and disconnect the plug connection.
  • Page 140: Removing And Installing Start/Stop Button And Immobiliser Reader Coil For Emergency Start

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove the noise insulation from the wheelhouse to reach the aerial -1-. – Take off aerial -1- from wheelhouse and disconnect plug -2-. Installing Installation is carried out in the reverse order. When installing, observe the following: –...
  • Page 141: Lock With Control Unit For Elv J764

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Disconnect the plug from the button -1- and from the reader coil -2-. – Insert two small cross-head screwdrivers (e.g. watch-and- clock screwdrivers) into the openings -arrows- and press the sheet pegs.
  • Page 142: Parking Aid And Park Steering Assistant

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Parking aid and park steering assis‐ tant ⇒ “11.1 Summary of components”, page 134 ⇒ “11.2 Remove and install parking aid control unit J446 or park‐...
  • Page 143 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Front right sender for park steering assistant ❑ Removing and installing ⇒ “11.5 Removing and installing parking aid senders and park steer‐ ing assistant”,...
  • Page 144: Remove And Install Parking Aid Control Unit J446 Or Parking Aid And Park Steering Assistant Control Unit J791

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 11 - Rear parking aid warning buzzer - H15- ❑ Removing and installing ⇒ “11.4 Removing and installing the rear parking aid warning buzzer H15 ”, page 137 11.2...
  • Page 145: Removing And Installing The Rear Parking Aid Warning Buzzer H15

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Use a small screwdriver to push the warning buzzer -1- out of the support -2-. – Disconnect plug. Right-hand drive: Warning buzzer -1- is located above the fuse holder.
  • Page 146: Removing And Installing Parking Aid Senders And Park Steering Assistant

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Loosen headlining ⇒ Body Work; Rep. gr. 70 and carefully hang the rear part downward. – Loosen and remove expanding rivets -arrows-. – Disconnect plug -1- and remove warning buzzer -2-.
  • Page 147: Parking Aid Sender Holder - Making Holes, Assignment, Fitting Location, Gluing Procedure

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove the mounting lugs -arrows A-. – Press out the sender -1- on the outer side of the shock ab‐ sorber inwards. – Unplug connector -2-.
  • Page 148: Self-Diagnosis Of The Parking Aid

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 11.6.3 Gluing procedure of the sender holders Note ♦ Park steering assistant sender holders have a countersink collar. Its visible area -1- must be painted the same colour as the bumper.
  • Page 149: Optical Parking Assistant (Rear View Camera)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Optical parking assistant (rear view camera) ⇒ “12.1 General description”, page 141 ⇒ “12.2 Summary of components: Rear view camera system”, page 141 ⇒ “12.3 Removing and installing rear view camera system”, page 12.1...
  • Page 150: Removing And Installing Rear View Camera System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Control unit with display for radio and navigation - J503- ❑ Removing and installing ⇒ “1.6 Removing and in‐ stalling the Infotainment display/control unit”,...
  • Page 151 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Release the grip with the camera -1- from the catches -arrows- step by step and remove. – Unlock and disconnect the connector of the rear view camera.
  • Page 152: Lights, Bulbs, Switches - Interior

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 96 – Lights, bulbs, switches - interior Interior Lights ⇒ “1.1 Lights in the roof lining”, page 144 ⇒ “1.2 Removing and installing the rear interior light on the left and right, replace”, page 147...
  • Page 153 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Loosen the cover -2- out of the catches using the removal wedge - 3409- and tilt out towards the bottom. – Unscrew screws -arrows- (2 Nm) and tilt out the interior light -1- and suspend it from the installation frame -3-.
  • Page 154 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unlock the catches -arrows- and remove the sliding roof switch from the trim panel. Installation is carried out in the reverse sequence. 1.1.4 Removing and installing the rear interior...
  • Page 155: Removing And Installing The Rear Interior Light On The Left And Right, Replace

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing the rear interior light on the left and right, replace Removing – Carefully release the catch -arrow- with a small cross-head screwdriver, tilt out the interior light and remove.
  • Page 156: Removing And Installing Glove Compartment Light In The Front Centre Console

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Push out the defective light bulb (W5W) and replace it. – If necessary disconnect the plug and remove the light. Installing Installation is carried out in the reverse sequence.
  • Page 157: Remove And Install The Footwell Lighting For The Driver And Front Passenger

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Tilt out the cover of the light -arrow-. – Carefully pull the light bulb (W5W) out of the socket and mount a new one. Installing Installation is carried out in the reverse sequence.
  • Page 158: Removing And Installing Rear Footwell Lighting

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Tilt out the cover of the light -arrow-. – Carefully pull the light bulb (W5W) out of the socket and mount a new one. Installation is carried out in the reverse sequence.
  • Page 159: Removing And Installing Luggage Compartment Light

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Carefully pull the light bulb (W5W) out of the socket and mount a new one. Installation is carried out in the reverse sequence. Removing and installing luggage com‐...
  • Page 160: Interior Switches, In The Dash Panel, The Centre Console And The Doors

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Interior switches, in the dash panel, the centre console and the doors ⇒ “2.1 Removing and installing light switch”, page 152 ⇒ “2.2 Removing and installing headlight range control regulator”, page 152 ⇒...
  • Page 161: Removing And Installing Switches In Centre Console

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Press together the lateral securing tabs on the adjuster for the headlamp range control -arrows-. – Pull the adjuster for headlamp range control -A- to the rear out of the mounting frame in the dash panel casing.
  • Page 162: Removing And Installing The Switch For The Power Window Lifter

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Remove the display unit for Infotainment, do not disconnect the cables ⇒ “1.6 Removing and installing the Infotainment display/con‐ trol unit”, page 33 – Push switch and indicator light -1- out of the central air outlets from the rear -arrow-.
  • Page 163 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Slacken the control element out of the catch pegs -arrows- and remove. Installation is carried out in the reverse sequence. 2.5.2 Switch on passenger side and rear Removing –...
  • Page 164: Removing And Installing The Passenger Side Glove Box Light Switch

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 2.5.3 Removing and installing mirror adjuster switch Removing – Remove top cover of the tightening handle -1- -arrow-. – Unclip switch -21- -arrows- and take it out of the cover -1-.
  • Page 165: Removing And Installing Interior Monitoring Deactivation Switch E 267 And Deactivation Button For Vehicle Inclination Sender E

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing and installing interior moni‐ toring deactivation switch -E 267- and deactivation button for vehicle inclina‐ tion sender -E 360- Removing – Switch off the ignition and all electrical components.
  • Page 166: Components In The Luggage Compartment And Tailgate

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Components in the luggage compart‐ ment and tailgate ⇒ “3.1 Removing and installing the switch for the luggage com‐ partment lighting”, page 158 ⇒ “3.2 Removing and installing the tailgate release switch”, page...
  • Page 167: Front Camera For Diver Assistance Systems R242

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Front camera for diver assistance systems - R242- ⇒ “4.1 Removing and installing front camera”, page 159 ⇒ “4.2 Removing windscreen heating plate”, page 160 Further information and description of function: ⇒...
  • Page 168: Removing Windscreen Heating Plate

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Push the cover -1- forward -arrow A- then downward -arrow B-. – Unclip the front camera -2- from the holding clamps -1- -arrow A-. – Pull front camera -2- out of the holder -arrow B- and disconnect the plug connection -3-.
  • Page 169: Horn

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Horn ⇒ “5.1 Removing and installing horn”, page 161 Removing and installing horn Caution The tone pitch of the horn is set at the factory. It is prohibited...
  • Page 170: Anti-Theft Warning System

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Anti-theft warning system ⇒ “6.1 General points”, page 162 ⇒ “6.2 Removing and installing the horn H12 ”, page 162 ⇒ “6.3 Removing and installing interior monitoring sensor G273 and vehicle inclination sender G384 ”, page 163...
  • Page 171: Removing And Installing Interior Monitoring Sensor G273 And Vehicle Inclination Sender G384

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unscrew nuts -2- and remove alarm horn with holder -1-. – Disconnect plug. Installing Installation is carried out in the reverse sequence. Removing and installing interior moni‐...
  • Page 172: Sockets, Cigarette Lighter

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Sockets, cigarette lighter ⇒ “7.1 Removing and installing the 12 V power socket/cigarette lighter in the centre console”, page 164 ⇒ “7.2 Removing and installing the luggage compartment 12 V power socket”, page 164...
  • Page 173 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Further information and description of function: ♦ ⇒ Owner's manual Octavia III ♦ ⇒ Self-study programme No. 97 ; Škoda Octavia III Vehicle presentation Special tools and workshop equipment required ♦...
  • Page 174 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – If required, separate from the latching mechanism -arrow- and remove socket outlet bracket -2- from the trim -1-. – Screw out screws -2-, slightly lift inverter with socket -1- and push it out of the centre console.
  • Page 175: Immobiliser

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Immobiliser The model Octavia III features the immobiliser of the fifth gener‐ ation with on-line connection and Download. The main compo‐ nent of the fifth generation immobiliser is a central database, in which all of the theft-relevant data from the participating control units is stored.
  • Page 176: Ignition Key

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 ♦ 01 – Self-diagnosable systems ♦ Immobiliser ♦ Operation ♦ Adjust dash panel insert Ignition key All – even re-ordered – ignition keys are already precoded at the factory for a specific vehicle and can only be adapted to this ve‐...
  • Page 177: System Test Result (Online Connection)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 ♦ Electrical system ♦ 01 – Self-diagnosable systems ♦ Immobiliser ♦ Operation ♦ New identity System test result (online connection) The following processes are performed with this test program: ♦...
  • Page 178: Wiring

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 97 – Wiring Fuse holder and relay carrier ⇒ “1.1 Removing and installing relay holder and fuse holder be‐ hind dash panel”, page 170 ⇒ “1.2 Removing and installing relays and fuse holder in the en‐...
  • Page 179: Removing And Installing Relays And Fuse Holder In The Engine Compartment And E-Box (Relays And Fuse Holder In The Engine Compartment)

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Upon removal of the central tube for the dashboard, remove the relay and fuse holder -3- and then screw out screws -1- and -2- (3 Nm).
  • Page 180 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Removing – Disconnect battery earth strap ⇒ “2.3.1 Disconnecting battery”, page 2 – Remove engine control unit and lay it to the side with connec‐ ted cables: •...
  • Page 181 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – If the fuse holder and relay holder are fully removed, loosen nuts -1, 2, 4, 5, 6- and screw out screw -3- and loosen electrical cables -arrow-.
  • Page 182: Control Units

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Control units ⇒ “2.1 Vehicle voltage control unit J519 ”, page 174 ⇒ “2.2 Data bus diagnostic interface Gateway”, page 178 Vehicle voltage control unit - J519-...
  • Page 183 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Parking aid control unit - J446- or parking aid and park steering assistant control unit - J791- ❑ Equipment variants with parking aid or parking...
  • Page 184 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 2.1.2 Summary of components - Right-hand drive 1 - Vehicle voltage control unit holder - J519- 2 - Vehicle voltage control unit - J519- ❑ ⇒ “2.1.3 Removing and...
  • Page 185 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Disconnect plug connections -1, 2, and 3-. Note After unlocking from the guide -6- push the middle plug connec‐ tion downwards (if installed). – For unplugging the plugs, successively press together the catches on the plug connections -1- and remove the plugs on the control unit by swivelling out the clamp -arrow-.
  • Page 186: Data Bus Diagnostic Interface Gateway

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Unlock catches -arrow-, tilt control unit -4- out of the holder -5- and remove downwards and towards you. Installing Installation is carried out in the reverse order. When installing,...
  • Page 187 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 1 - Connector ❑ Exact contact assignment⇒ Current flow diagrams, Electri‐ cal fault finding and Fit‐ ting locations 2 - Data bus diagnostic inter‐ face Gateway - J533- 3 - Screw ❑...
  • Page 188 Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 – Press safety catch and disconnect plug connection -1-. – Press catches -arrows- and pull control unit downwards -3- out of the holder-2-. Installing Installation is carried out in the reverse sequence.
  • Page 189: Vehicle Diagnosis, Measurement And Information Systems, Diagnostic Connection

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Vehicle diagnosis, measurement and information systems, diagnostic con‐ nection Following descriptions see Workshop Manual “Electrical System – General notes” ⇒ Electrical System – General notes; Rep. gr.
  • Page 190: Wiring Loom And Plug Repair, Contact Surface Cleaning

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Wiring loom and plug repair, contact surface cleaning All the notes and comments to the following chapters can be found in the Workshop Manual “Electrical System – General notes”...
  • Page 191: Vehicle Diagnosis, Testing And Information Systems

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Vehicle diagnosis, testing and infor‐ mation systems The following descriptions can be found in the Workshop Manual “Electrical System – General notes” ⇒ Electrical System – Gen‐...
  • Page 192: Wiring Loom And Plug Repair

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Wiring loom and plug repair All the notes and comments to the following chapters can be found in the Workshop Manual “Electrical System – General notes” ⇒ Electrical System – General notes; Rep. gr. 97 .
  • Page 193: Use Contact Surface Cleaning Set Vas 6410

    Octavia III 2013 ➤ , Octavia III 2014 ➤ Electrical system - Edition 12.2014 Use contact surface cleaning set - VAS 6410- All the notes and comments to the following chapters can be found in the Workshop Manual “Electrical System – General notes”...

This manual is also suitable for:

Octavia iii 2014

Table of Contents