Telescope End Panels For Dual Tables - Knoll Antenna Telescope Installation Instructions And Parts Manual

End Panels

Telescope End Panels for Dual Tables

Pattern Numbers Represented:
Telescope End Panel, YEP____
Parts List:
End Panel Connector Link (A)
Dovetail Linking Bracket (B)
End Panel Block (C)
End Panel Leg Brace, Right Hand (D)
End Panel Leg Brace, Left Hand (E)
NOTE
: Handedness is determined as you face the
end of the desk base
Polyurethane Grip Tape (F)
¼-20 x .75" Flat Head Machine Screw (G)
¼-20 x 1.25" Flat Head Machine Screw (H)
¼-20 x .5" Black Flat Head Screw (I)
End Panel with Glides
Adjustable Dual Table (With Intermediate or End
Application Base)
Tools Needed:
Right-Angle Ratcheting Power Driver with #3 Phillips Bit
STEPS
NOTE: Before attaching an End Panel, the
adjustable dual table (with intermediate or end
application base) should be fully assembled
(see previous installation guide pages).
The crossbar adjacent to the end panel must
be a "mid-crossbar" type, with dovetail linking
brackets already installed, to accept connector
links.
The connector link that came with the table
base will be too wide to properly connect
the End Panel to the base and should be
discarded for this end-panel application.
1. Slide the (2) End Panel Connector Links
(A) down onto the linking brackets
previously attached to the crossbar.
Do not fasten from below yet.
2. Attach (2) Dovetail Linking Brackets (B)
to the predrilled holes in the center of
the end panel, using (2) ¼ -20 x .75" Flat
Head Machine Screws (G) per bracket.
Antenna Telescope Installation Instructions
® ™
October 2018
(A) 3AF4111*
(E) 3AF4112L*
(I) 3AB4190
3. Attach (2) End Panel Blocks (C) to the
predrilled holes on the bottom of the
end panel, using (2) ¼-20 x 1.25" Flat
Head Machine Screws (H) per block.
4. Apply a strip of Polyurethane Grip Tape (F)
to the inside curved surface of both the
Right-Hand End Panel Leg Brace (D) and
Left-Hand End Panel Leg Brace (E).
5. Place the End Panel in position, located so
that the Dovetail Linking Brackets (B) are in
line with the End Panel Connector Links (A).
6. Position the Right-Hand End Panel Leg
Brace (D), just above the corresponding
End Panel Block (B) on the End Panel with
the curved (taped) surface against the inner
(toward the other column) surface of the
column. Slide the brace down to engage
the End Panel Block (B), and attach using
a ¼-20 x .5", Black Flat Head Screw (I). 3
(B) 3AF4009 (C) 3AF4114
(F) 6AA4233 (G) 7418440
7. Repeat step 6 for the Left-Hand
End Panel Brace (D).
8. Raise both End Panel Connector Links (E)
off the linking brackets on the crossbar, and
reposition them as to engage both sets of
Dovetail Linking Brackets (B), i.e.: the brackets
on the crossbar and on the End Panel.
9. Extend the glides in the End Panel to level the
panel so that the End Panel Connector Links
(E) rest on the bottom flanges of both pairs
of Dovetail Linking Brackets (B). Fasten the
connector links to the linking brackets with ¼
- 20 x .75" flat head machine screws (G), from
below.
Antenna Telescope
®
(D) 3AF4112R* (D)
(H) 7197100
™
77