Knoll Antenna Telescope Installation Instructions And Parts Manual page 70

Telescope Return Bases
Step 10 & 16
Main to Return Tie
"W" Bracket (F)
¼
-14 x 7/8" Pan Head
Machine Scews (M)
Pre-drilled
Return Top
Step 18
Handset Control
Switch (R)
/
#6 x 5 " Wood
8
Step 14
Screws (S)
Spacer (P)
#12 x ¾" Flat
Head Black Wood
Screw (Q)
PREPARE THE RETURN TOP
10. Attach the (2) Main to Return Tie "W"
Brackets (F) to the end of the return top using
(2) ¼-14 x 7/8" pan head machine screws
(M), per bracket, into the pilot holes.
Note
: The midline of the "W"
bracket is intentionally inset from
the edge of the return top.
POSITION THE RETURN ASSEMBLY
11. Set the primary structure to a height similar
to the return structure (typically its lowest
position), and place the Return Rail Hook
Top Bracket (G) over the primary structure's
front rail. The primary table desk top will
need to be loosened to allow the hook to
be installed. Prop or have someone hold
the shorter rail as needed, and continue.
12. Verify that the return structure is in the
appropriate location for the depth of the return
top, then secure the rail bracket in place by
attaching a Return Rail Clamp Bottom Bracket
(H) with (1) ¼ -20 X 1" machine screw (K).
Note
: The return column is always
centered on the return top depth.
13. Attach the End Cap with Support Tab (I)
to the underside of the primary top with
a #14 x 1" flat head wood screw (L).
Antenna Telescope Installation Instructions
® ™
October 2018
Step 15
#14 x 1" Flat Head
Wood Screws (L)
INSTALL THE RETURN TOP
: As the rail clamp assembly and end
Note
cap are only pressed into the ends of the rails,
install the tops immediately. DO NOT attempt
to move the station until tops are in place and
the return structure is completely fastened.
14. Lay the return top on the return base assembly,
sliding the "W" brackets (F) under the primary top.
Be sure to not disengage the rail clamp assembly
(G/H) from the end of the return rail. Place a
Spacer (P) between the top of each rail and the
underside of the top, centered on the width of the
top. Spacers are attached to the top using (1) #12
X ¾" flat head black wood screw (Q) per spacer.
15. Attach return top to base using (4) #14 x
1" flat head wood screws (L) per cradle.
16. Secure the "W" brackets (F) to the
primary top using (2) ¼-14 x 7/8" pan
head wood screws (M), per bracket.
ATTACH THE RETURN ELECTRICAL
COMPONENTS
17. Disconnect the temporarily positioned handset
cable from the primary structure's housing
assembly, and reconnect it into a housing
outlet in the return column assembly. Connect
one end of the iDrive Cable into the second
outlet in the return and the other end into the
now open outlet in the primary structure.
Antenna Telescope
®
Step 13
End Cap with
Support Tab (I)
#14 x 1" Flat
Head Wood
Screw (L)
Step 12
Return Rail Clamp
Bottom Bracket (H)
¼
-20 x 1" Flat
Head Machine
18. Using (2) #6 x / " wood screws (S) mount
5
8
the Handset Control Switch to the underside
of the return top, at the front edge.
PERFORM A RESET FOR THE THREE
COLUMNS IN EACH STATION
19. Apply approximately 100 lbs of weight to the
station. Press and hold both UP and DOWN
buttons for ten seconds. After releasing the
buttons, press and hold the DOWN BUTTON
until all three columns bottom out. Press the
UP button and the station will be ready to
perform normally. Remove the weight. Run
the station all the way up and down again to
ensure there are no issues with the columns.
LEVEL TABLES
20. Place the tables in their final positions and level
by extending the leveling glides as needed.
21. When levelers are extended more than
½", install the Helical Glide Shroud. See
Helical Glide Installation Instructions.
INSTALL POWER STRIP ACCESSORY
(WHERE APPLICABLE)
See Power Strip Installation Instructions.
INSTALL CLEAT PLATE & CLEAT PLATE COVER
ACCESSORIES (WHERE APPLICABLE)
See Cleat Plate and Cleat Plate
Cover Installation Instructions.
™
70