Table of Contents
Advertisement
control block (AUX bus operation mode) in the
Setup menu (see page 382).
Using four DME channels on one keyer
1
In the <DME Select> group of the M/E-1 >Key1
>Processed Key menu (1116), select consecutive
DME channels.
Select [DME1] for the first channel, [DME2] for the
second channel, [DME3] for the third channel, and
[DME4] for the fourth channel.
2
Select the second channel video signal.
Select using any of the following methods.
• On the cross-point control block, press delegation
button [DME EXT] on the cross-point pad and select
a signal using the cross-point buttons in the 1st row/
2nd row.
• On the cross-point control block in key/AUX bus
delegation mode, press the [DME EXT] button in
the 1st row and select a signal using the cross-point
buttons in the 2nd row.
Notes
• You can assign the DME external video bus using
the [UTIL] button on the cross-point pad of the
cross-point control block (see page 73).
• You can assign a DME external video bus delegation
button to the 1st row or 2nd row of the AUX bus
control block (AUX bus operation mode) in the
Setup menu (see page 382).
3
Select the third channel video signal.
Select using any of the following methods.
• On the cross-point control block, press delegation
button [DME UTL1] on the cross-point pad and
select a signal using the cross-point buttons in the 1st
row/2nd row.
• On the cross-point control block in key/AUX bus
delegation mode, press the [DME UTIL1] button in
the 1st row and select a signal using the cross-point
buttons in the 2nd row.
Notes
• You can assign the DME utility 1 bus using the
[UTIL] button on the cross-point pad of the cross-
point control block (see page 73).
• You can assign a DME utility 1 bus delegation
button to the 1st row or 2nd row of the AUX bus
control block (AUX bus operation mode) in the
Setup menu (see page 382).
4
Select the third channel video signal.
Select using any of the following methods.
• On the cross-point control block, press delegation
button [DME UTL2] on the cross-point pad and
select a signal using the cross-point buttons in the 1st
row/2nd row.
• On the cross-point control block in key/AUX bus
delegation mode, press the [DME UTIL2] button in
the 1st row and select a signal using the cross-point
buttons in the 2nd row.
Notes
• You can assign the DME utility 2 bus using the
[UTIL] button on the cross-point pad of the cross-
point control block (see page 73).
• You can assign a DME utility 2 bus delegation
button to the 1st row or 2nd row of the AUX bus
control block (AUX bus operation mode) in the
Setup menu (see page 382).
To check DME usage status
You can check the DME operating status in the Status
>DME Status menu (3311) (see page 176).
Assigning a DME output signal as a
monitor signal
1
In the M/E-1 >Key1 >Processed Key menu (1116),
press [Monitor].
The Monitor menu (1116.1) appears.
2
Press [Monitor Set], turning it on.
3
In the <DME Select> group, select the DME channel
(DME1 to DME4) to be used.
This assigns the selected DME output to DME MON
V and DME MON K.
The lit colors of [DME1] to [DME4] indicate the DME
assignment.
Lit green: Indicates a DME currently being
monitored.
Lit amber: Indicates a DME which can be monitored.
Not lit: DME is not assigned.
Specifying the Key Output
Destination
Using a processed key keyer signal
(external processed key)
To select key fill and key source signals for a processed
key keyer on the AUX bus or edit preview bus, press [Ext
Proc Key] in the M/E-1 >Key1 >Processed Key menu
(1116), turning it on.
114
Advertisement
Table of Contents
