Settings Relating To Signal Outputs; Assigning Output Signals - Sony XVS Series User Manual

Settings Relating to
Signal Outputs
Configures settings for outputs 1 to 48.
This also configure format converter (FC) outputs 1 to 16.
Number of outputs
The number of outputs per connector board (4K format/
HD format) is given below.
Output connector board
Name Interface 4K
XKS-S8165 SDI output SDI
connector board
XKS-T8165 IP output NMI
connector board
a) 6 when the signal format is 1080P/59.94 or 1080P/50.
The maximum number of outputs is 48 for HD format and
12 for 4K format (with combination of four XKS-S8165 or
XKS-T8165 boards installed).
The maximum number of format converter outputs is 4 for
4K format (with combination of four XKS-S8165 or XKS-
T8165 boards installed).
4K format output settings
Four output connectors are assigned as a single group to a
4K signal.
A single group comprises four outputs in numeric order
starting from the first output, and settings are applied to the
first number in each group.
Output connector number Setting number
1, 2, 3, 4
5, 6, 7, 8
9, 10, 11, 12
13, 14, 15, 16
(and so on)
1080P/59.94 and 1080P/50 format output settings
The number of outputs on an NMI connector board (XKS-
T8165) is half the number of connectors on an SDI
connector board (XKS-S8165).
On an NMI board, only odd-numbered outputs can be
configured.
Format converter outputs
Format converter outputs 1 to 16 corresponds to format
converter output connectors 1 to 16 of the output connector
board.
The number of format converter output connectors will
vary depending on the number of output connector boards
Number Number
of of FC
outputs outputs
HD 4K
3 12 1
3 12 1
a)
1
5
9
13
(and so on)
installed.
You can enable the format converter function if an XKS-
8460 Format Converter Board is installed.
For details about format converter output connectors, see
"XVS-8000 Multi Format Switcher" (page 60).
Notes
• In 4K format, only format converter outputs 1, 5, 9, and
13 can be configured.
• The following functions are not supported on format
converter outputs.
Video clips, vertical blanking, through mode, safe titles,
4:3 crop, AUX bus color corrector

Assigning Output Signals

1
In the Engineering Setup >Switcher >Output menu
(7333), press [Output Assign].
The Output Assign menu (7333.1) appears.
The status area shows a list of output signal numbers
and source names of assigned signals on the left.
2
In the <Output Assign> group, set the signals to
display in the list on the right.
[Re-Entry Source]: The following can duplicated and
assigned.
M/E-1 Out1 to Out6
M/E-2 Out1 to Out6
M/E-3 Out1 to Out6
M/E-4 Out1 to Out6
M/E-5 Out1 to Out6
P/P Out1 to Out6
M/E-1 to M/E-5 Proc Video
P/P Proc Video
M/E-1 to M/E-5 Proc Key
P/P Proc Key
Color Corrector 1, 2
DME Monitor Video
DME Monitor Key
Undefined
Color Bkgd 2
Frame Memory 1 to 20
[Aux Bus]: The following cannot be duplicated and
assigned.
Preset
Edit Preview
AUX1 to 48
1) Signals are configured using the Engineering Setup >Switcher
>Config >M/E Output Assign menu (7331.1).
3
Select the output connector number and signal to
assign.
406
1)
1)
1)
1)
1)
1)