Table of Contents
Advertisement
GB ©Bostitch. Not to be reproduced without permission. Unauthorised copies of this document do
EngLIsh
not constitute CE compliance for the products.
nOtE: The battery pack is not fully charged out of the carton.
Follow instructions outlined (see Charging a Battery).
FR ©BOSTITCH. Reproduction interdite sans permission préalable. Les copies non autorisées de
•
Read the Safety Instruction section of this manual.
ce document ne signifient en rien que les produits soient conformes aux normes CE.
•
Wear eye and ear protection.
•
Ensure magazine is empty of all fasteners.
DE ©BOSTITCH. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien
•
Check for smooth and proper operation of contact trip and
dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
pusher assemblies. Do not use tool if either assembly is not
functioning properly. NEVER use a tool that has the contact
NL ©BOSTITCH. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën
trip restrained in the actuated position.
van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
•
Keep tool pointed away from yourself and others.
•
Insert fully charged battery pack.
DK ©BOSTITCH. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør
Using the Trigger Lock-off (Fig. E)
ikke CE overholdelse for produkterne.
WARNING: To reduce the risk of serious personal injury,
do not keep trigger depressed when tool is not in use. Keep
FI ©BOSTITCH. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot
the trigger lock-off switch LOCKED (Fig. E) when the tool
eivät muodosta tuotteille CE-yhdenmukaisuutta.
is not in use.
WARNING: To reduce the risk of serious personal injury,
GR ©BOSTITCH. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
lock off trigger, disconnect battery pack from tool and
remove nails from magazine before making adjustments.
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
Each BOSTITCH nailer is equipped with a trigger lock-off
τα προϊόντα.
which when pushed to the right as shown in Figure E, prevents
the tool from firing a nail by locking the trigger and bypassing
IT ©BOSTITCH. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
power to the motor.
documento non garantiscono la conformità CE per i relativi prodotti.
When the trigger lock-off is pressed to the left, the tool will be
fully operational. The trigger lock-off should always be locked
NO ©BOSTITCH. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
off whenever any adjustments are made or when tool is not in
immediate use.
dokumentet oppfyller ikke kravene for CE-merking for produktet.
NOTICE: Do not store tool with battery pack installed. To
prevent damage to the pack and to ensure best battery
PT ©BOSTITCH. Reprodução proibida sem autorização prévia. As cópias não autorizadas deste
life, store battery packs out of the tool or charger in a cool,
documento não estão em conformidade com a CE para os produtos.
dry location.
Loading the Tool (Fig. F)
ES ©BOSTITCH. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
WARNING: Keep the tool pointed away from yourself and
others. Serious personal injury may result.
WARNING: Never load nails with the contact trip or
SE ©BOSTITCH. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
trigger activated. Personal injury may result.
documento no suponen la conformidad con las normas CE de los productos.
WARNING: Always remove battery pack before loading or
unloading nails. Serious personal injury may result.
PL ©BOSTITCH. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Load and Draw Method (Fig. A)
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
1. Load nails through the slot in the rear of the magazine and
prezentowanych produktów.
past the retaining clip.
2. Pull pusher
16
back behind nail stick and release.
CZ ©BOSTITCH. Niniejszy dokument nie może być kopiowany bez pozwolenia.
3. Ensure magazine pusher
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
Unloading The Tool (Fig. F, I)
prezentowanych produktów.
WARNING: The trigger lock-off should always be locked
off whenever any adjustments are made or when tool is
SK ©BOSTITCH. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
not in use.
dokumentu nie sú v súlade s CE pre dané výrobky.
1. Release pusher
16
so it is no longer applying force to the
nail ticks.
HU ©BOSTITCH. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
2. Slide nail sticks down and out through the slot in the rear of
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
the magazine.
34
is behind the last nail stick.
16
3. Open the jam clear latch
are no nails remaining.
Mode Selection (Fig. A, D)
The finish nailer is capable of firing nails using bump actuation
or sequential actuation. Before operating this tool, look at the
selector switch to determine the actuation mode. Read all
instructions before selecting actuation mode.
WARNING: Keep fingers AWAY from trigger when not
driving nails to avoid accidental fastener discharge.
NEVER carry tool with finger on trigger. In bump mode
tool will drive a nail if contact trip is bumped while trigger
is depressed.
Sequential Action
Use sequential actuation mode for intermittent nailing where
very careful and accurate placement and depth control is
desired. The sequential actuation mode provides the maximum
delivery of power for driving the longest nails.
to operate the nailer in sequential actuation mode:
1. Slide the selector switch
2
icon
.
2. Fully depress nosepiece against the work surface (motor
will start).
3. Pull trigger (nail will drive into work surface).
4. Release trigger.
5. Lift nosepiece off work surface.
6. Repeat steps 2 through 4 for next application.
NOTICE: The contact trip needs to be depressed followed
by a trigger pull for each nail followed by a release of both
the contact trip and trigger after each nail.
Bump Action
Bump action is intended for rapid nailing on flat, stationary
surfaces and typically most effective for applications that require
driving shorter nails.
When the tool is set in the bump actuation mode, two
methods of tool operation are available: place actuation and
bump actuation.
Slide the selector switch
to operate the tool using the place actuation method:
WARNING: A nail will be driven each time the trigger is
depressed as long as the contact trip remains depressed.
1. Depress the contact trip against the work surface.
2. Depress the trigger.
to operate the tool using the bump actuation method:
1. Depress the trigger.
2. Push the contact trip against the work surface. As long as
the trigger is depressed, the tool will drive a nail every time
the contact trip is depressed. This allows the user to drive
multiple nails in sequence.
WARNING: Do not keep trigger depressed when tool is not
in use. Keep the trigger lock-off in the locked position when
the tool is not in use.
5
on the nosepiece to verify there
8
to expose the single nail
to expose the triple nail icon
8
.
Advertisement
Table of Contents
