Optima - G 2420/G 243X; Table 080-38: Service Mode Summary, G 2120/G 214X/G 2150 - Miele G 1 Series Technical Information
Hide thumbs
Also See for G 1 Series:
- Operating instructions manual (76 pages) ,
- Manual (46 pages) ,
- Operating instructions manual (64 pages)
Table of Contents
Advertisement
G 1xxx/G 2xxx
4. Immediately press the Start/Stop button 3 times; on the 3rd time, hold
until the "Start/Stop" LED flashes.
5. Release the Start/Stop button.
6. If the "Start/Stop" LED does not light up, repeat the procedure.
Acknowledgement indicator:
The "Start/Stop" LED flashes slowly (1 flash per second).
Options:
Function
Display and delete fault
memory
Component test
Operating hours check
LED test
Table 080-38: Service Mode Summary, G 2120/G 214x/G 2150
4.3.8
Optima - G 2420/G 243x
Initial requirements:
1. Close the door.
2. Switch off the appliance.
Accessing:
1. Press and hold the Start/Stop button.
2. Switch on the appliance.
3. Release the Start/Stop button.
4. Immediately press the Start/Stop button 3 times; on the 3rd time, hold
Programming
Press the Program (or
Delay Start for G 2143)
button 1x. If the "Rinse"
LED displays a fault,
check if further faults were
registered by briefly
pressing the Start/Stop
button. To delete the fault
memory, press and hold
Start/Stop until the
"Rinse" LED goes out.
Press the Program (or
Delay Start for G 2143)
button 2x. Press the
Start/Stop button to
start the component test.
Press Start/Stop again to
activate the next
component.
Press the Program (or
Delay Start for G 2143)
button 3x. Press the
Start/Stop button.
Press the Program (or
Delay Start for G 2143)
button 4x. Press the
Start/Stop button.
215
Technical Information
Display
The "Rinse & Hold" LED flashes 1x
rapidly. If faults were registered,
they are indicated by the "Rinse"
LED. (Example: Fault code F14:
The "Rinse" LED flashes 1x slowly
and 4x rapidly at intervals). Fault
code summary, see Table 080-2.
The "Rinse & Hold" LED flashes 2x
rapidly. The "Rinse" LED indicates
which component is currently
activated. Test sequence and
background information, see
Section 080-2.2.
The "Rinse & Hold" LED flashes 3x
rapidly. The "Rinse" LED's
flash pattern indicates the saved
operating hours: Each slow flash of
the "Rinse" LED corresponds to
1000 h and each rapid flash
corresponds to 100 h.
The "Rinse & Hold" LED flashes 4x
rapidly. All LEDs light up.
Advertisement
Table of Contents
Need help?
Do you have a question about the G 1 Series and is the answer not in the manual?
Questions and answers
INTAKE AND DRIAN COMES ON ALL THE TIME NEED TO READ WHAT THE CODES ARE FOR THIS UNIT G2141
For the Miele G 1 Series dishwasher model G2141, when the "Intake/Drain" light is on continuously, it typically indicates a fault condition. Based on the context, error codes like F01 or other FXX codes may be shown on the display, and the "Intake/Drain" LED may flash or stay on. Specific error codes are not directly listed for G2141 alone, but models like G2120 and G214x share similar fault indications:
- The “Intake/Drain” LED may flash.
- The time display may show FXX (e.g., F01).
- LEDs like “Wash/Rinse,” “Drying,” and “End” may flash together.
These symptoms generally suggest a fault related to water intake or drainage, such as a blocked filter, kinked hose, or faulty pump.
This answer is automatically generated