Fault Code Summary; Table 080-2: Fault Code Summary - Miele G 1 Series Technical Information
Hide thumbs
Also See for G 1 Series:
- Operating instructions manual (76 pages) ,
- Manual (46 pages) ,
- Operating instructions manual (76 pages)
Table of Contents
Advertisement
G 1xxx/G 2xxx
3.8
Fault Code Summary
Note:
Not all fault codes apply to all model numbers.
Fault Code
F00
F01 (see Section 080-3.11)
F02 (see Section 080-3.12)
F11 (see Section 080-3.13)
F12 (see Section 080-3.14)
F13 (see Section 080-3.15)
F14 (see Section 080-3.16)
F15 (see Section 080-3.17)
F18 (see Section 080-3.18)
F19 (see Section 080-3.19)
F24 (see Section 080-3.20)
F25 (see Section 080-3.21)
F26 (see Section 080-3.22)
F32 (see Section 080-3.23)
F33 (see Section 080-3.24)
F36 (see Section 080-3.25)
F40 (see Section 080-3.26)
F42 (see Section 080-3.27)
F47 (see Section 080-3.28)
F51 (see Section 080-3.29)
F52 (see Section 080-3.30)
F53 (see Section 080-3.31)
F63 (see Section 080-3.32)
F67 (see Section 080-3.33)
F68 (see Section 080-3.34)
F69 (see Section 080-3.35)
F70 (see Section 080-3.36)
F78 (see Section 080-3.37)
F79 (see Section 080-3.38)
F84 (see Section 080-3.39)
F85 (see Section 080-3.40)
F86 (see Section 080-3.41)
F87 (see Section 080-3.42)
F88 (see Section 080-3.43)
F91 (see Section 080-3.44)
Table 080-2: Fault Code Summary
Possible Fault
No fault registered
Water/heating NTC or leads short-circuited
Water/heating NTC or leads open-circuited
Drainage fault
Water intake fault at start of step
Water intake fault at end of step
Water intake fault: Heater pressure switch
Water intake fault: Hot water
Flow meter stationary state monitor
Flow meter stiff and not turning freely
Heater relay contact
Target temperature fault
Boiling protection
Door lock does not close
Door lock does not open
Door lock switch defective
Electronic fault
Line frequency registration fault
Faulty electronic interface (between BAE & SLT)
Heater pressure switch
Heater pressure switch has reset during heating
Speed sensor fault
Slide shutter fault
Circulation pump speed too low
Circulation pump operating after switch-off
Circulation pump blocked
Float switch fault
Circulation pump fault
Circulation pump interaction fault
Slide shutter positioning fault
Slide shutter signal change fault
Lid contact - salt
Sensor softener fault
Turbidity sensor fault
Load size registration inactive
137
Technical Information
Advertisement
Table of Contents
Need help?
Do you have a question about the G 1 Series and is the answer not in the manual?
Questions and answers
INTAKE AND DRIAN COMES ON ALL THE TIME NEED TO READ WHAT THE CODES ARE FOR THIS UNIT G2141
For the Miele G 1 Series dishwasher model G2141, when the "Intake/Drain" light is on continuously, it typically indicates a fault condition. Based on the context, error codes like F01 or other FXX codes may be shown on the display, and the "Intake/Drain" LED may flash or stay on. Specific error codes are not directly listed for G2141 alone, but models like G2120 and G214x share similar fault indications:
- The “Intake/Drain” LED may flash.
- The time display may show FXX (e.g., F01).
- LEDs like “Wash/Rinse,” “Drying,” and “End” may flash together.
These symptoms generally suggest a fault related to water intake or drainage, such as a blocked filter, kinked hose, or faulty pump.
This answer is automatically generated