Table 080-5: Service Programming Mode Summary, G 118X/G 2170/G 218X - Miele G 1 Series Technical Information
Hide thumbs
Also See for G 1 Series:
- Operating instructions manual (76 pages) ,
- Manual (46 pages) ,
- Manual (14 pages)
Table of Contents
Advertisement
Technical Information
Function
Activating/deactivating
improved drying
Appliance width setting
Appliance height setting
Model setting
Country setting
Table 080-5: Service Programming Mode Summary, G 118x/G 2170/G 218x
1
If the electronic needs to be replaced during servicing, the following steps must be taken
during programming: In the first step, set the country specification and model, then switch
off the appliance. Repeat access and then set appliance width and height, and the
appropriate supply water hardness.
2
If the dishwasher is connected to an external ion exchanger water softener (i.e. that
needs to be regenerated with salt), the water hardness delivered by the system must be
set. If this value is unknown, set to 8°d (8.6 grains per gallon).
3
Circulation Turbothermic drying (UTT) version 1 (w/condenser), version 2 (w/out condenser).
4
The SER country specification includes the following countries: Portugal, France, the
Netherlands, Belgium and Great Britain.
Save and quit:
Switch off the appliance.
Programming
Press the Program button
27x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
Press the Program button
35x. To make the desired
setting, press and hold the
1
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
Press the Program button
36x. To make the desired
setting, press and hold the
1
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
Press the Program button
38x. To make the desired
setting, press and hold the
1
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
Press the Program button
39x. To make the desired
setting, press and hold the
1
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
168
G 1xxx/G 2xxx
Display
The "Intake/Drain" LED flashes
2x slowly and 7x rapidly.
"SaniWash" LED is off: Standard
setting; "SaniWash" LED flashes:
Improved drying – depending on the
program, drying time is extended
and the final rinse temperature
increased.
The "Intake/Drain" LED flashes 3x
slowly and 5x rapidly. "SaniWash"
LED is off: Appliance width 24"
(60cm) (standard setting);
"SaniWash" LED flashes: Appliance
width 18" (45cm).
The "Intake/Drain" LED flashes 3x
slowly and 6x rapidly. "SaniWash"
LED is off: Standard appliance
height (G 1xxx); "SaniWash" LED
flashes: XXL models (G 2xxx).
The "Intake/Drain" LED flashes 3x
slowly and 8x rapidly. "SaniWash"
LED off: Models without drying fan;
"SaniWash" LED flashes: Models
3
with UTT version 1 or 2.
The "Intake/Drain" LED flashes 3x
slowly and 9x rapidly. The
"SaniWash" LED's flash pattern
indicates which country is set: 1x:
Europe; 2x: Australia; 3x: USA; 4x:
Japan; 5x: Italy/Spain; 6x: Southern
4
Europe.
Advertisement
Table of Contents
Need help?
Do you have a question about the G 1 Series and is the answer not in the manual?
Questions and answers
INTAKE AND DRIAN COMES ON ALL THE TIME NEED TO READ WHAT THE CODES ARE FOR THIS UNIT G2141
For the Miele G 1 Series dishwasher model G2141, when the "Intake/Drain" light is on continuously, it typically indicates a fault condition. Based on the context, error codes like F01 or other FXX codes may be shown on the display, and the "Intake/Drain" LED may flash or stay on. Specific error codes are not directly listed for G2141 alone, but models like G2120 and G214x share similar fault indications:
- The “Intake/Drain” LED may flash.
- The time display may show FXX (e.g., F01).
- LEDs like “Wash/Rinse,” “Drying,” and “End” may flash together.
These symptoms generally suggest a fault related to water intake or drainage, such as a blocked filter, kinked hose, or faulty pump.
This answer is automatically generated