Table of Contents
Advertisement
5. INSTALLATION.
Read and respect the Safety Information described
•
in Chapter of this document. Failure to obey some
of the instructions described in this manual can result in a
serious or very serious accident to persons in direct contact
or in the vicinity, as well as failures in the device and/or
loads connected to it.
The cross sections of the cables used for installation must
•
be in accordance with the currents indicated on the name-
plate, in compliance with local and/or national low-voltage
electrotechnical regulations.
These currents will also determine the minimum sizes of
the equipment's protection devices, which will be in ac-
cordance with to the selectivity indicated in Chapter of
this document.
This chapter presents the relevant requirements to place
•
and wire the SLC ADAPT2 modular series of UPSs. As each
site has its own placement and installation characteristics,
it is not the purpose of this chapter to provide precise step-
by-step instructions, but rather to be used as a guide for
general procedures and practices to be observed by quali-
fied personnel (as defined in safety instructions EK266*08).
5.1. RECEPTION.
All cabinets are supplied mechanically attached to wooden
•
pallets, with a cardboard or wooden casing, according to
model. While the risk of tipping over is minimised, these
must be handled with caution, especially those with 6 slots,
because of their greater height, and especially when there
is a slope.
It is dangerous to handle the equipment care-
ˆ
lessly when it is on the pallet, as it could over-
turn and cause serious or very serious impact injuries to
operators, falling onto them and/or trapping them. Pay
attention to section 1.2.1. of the safety instructions
-EK266*08- in all matters relating to the handling,
movement and siting of the unit.
Use the most suitable means to move the UPS while it is
•
packed, with a pallet jack or forklift.
Whenever the manipulation is manipulated, the weights
•
indicated in Chapter in the technical characteristics, ac-
cording to model, must be taken into account.
5.1.1. Reception, unpacking and contents.
Reception. Check that:
•
The data on the label affixed to the packaging corre-
ˆ
sponds to that specified on the order. Once the UPS is
unpacked, check the previous data with those of the
device nameplate.
If there are discrepancies, report the issue as soon as
possible, citing the device's manufacturing number and
delivery note references.
It has not suffered any mishaps during transportation
ˆ
(packaging and impact indicator in perfect condition).
Otherwise, follow the protocol indicated on the label at-
tached to the impact indicator, located on the packaging.
22
Unpacking.
•
To verify the contents it is necessary to remove the
ˆ
packaging.
Complete the unpacking according to the proce-
dure in section .
Contents.
•
The equipment itself, consisting of a certain number of
ˆ
power modules.
Additional UPS cabinets, if any, for parallel connection,
ˆ
and the connection bus cables.
The battery cabinets, if any, to be connected to the UPS
ˆ
cabinets.
Once the reception is completed, it is advisable to re-pack
•
the UPS until it is put into service in order to protect it
against mechanical shock, dust, dirt, etc.
5.1.2. Storage.
The device storage shall be done in a dry, ventilated place
•
and protected from rain, dust, water splashes or chemical
agents. It is advisable to keep each device in its original
packaging as it has been specifically designed to ensure
maximum protection during transport and storage.
Do not store the equipment where the ambient temperature
•
exceeds the thresholds given in chapter .
When a battery pack is supplied with the UPS cabinet, ei-
•
ther in a cabinet, loose to be installed in your own cabinet,
on a rack or in any other way and not immediately installed
together, it should be stored in a cool, dry and ventilated
place at a controlled temperature of between 20 and 25°C.
In general and except in particular cases when
ˆ
batteries are supplied they are hermetically
sealed lead-calcium batteries. To avoid degradation
during storage, they must be recharged at the indicated
intervals according to the temperature to which they
are exposed (see date of last charge noted on the label
affixed to the packaging of the battery unit ).
Model information label.
MUY IMPORTANTE PARA LA VIDA DE LAS BATERÍAS DE Pb-Ca:
su degradación deben ser recargadas en los intervalos indicados. Respetar
el procedimiento referido en el manual de usuario del equipo.
VERY IMPORTANT FOR THE LIFETIME OF Pb-Ca BATTERIES:
their degradation, they must be recharged according to the stated interval
times. Respect the procedure referred in the equipment user's manual.
Fecha carga /
**-**-****
Charging date :
Charge date shipped from factory.
Space to write down the date of the new recharge.
Fig. 18. Label on the packaging of the battery pack.
Para evitar
ºC
Meses /
Months
In order to avoid
0 - 20
12
21 - 30
9
31 - 40
5
41 - 50
2,5
Fecha recarga /
Recharging date:
DY933B00 - 401AF000001
SALICRU
Advertisement
Table of Contents
