Table of Contents
Advertisement
5. INSTALLATION
Read and follow the Safety Information set out in
chapter 2 of this document. Failure to adhere to any of
the indications set out in chapter 2 may cause a serious or very
serious accident for those who are in direct contact with the
unit or who are in the vicinity, as well as faults in the unit and/
or in the loads connected to it.
In addition to the unit's user manual, other documents are sup-
plied on the documentation pen drive. Consult them and strictly
follow the indicated procedure.
The cross-sections of the cables used for the installation will be
in line with the currents indicated on the name plate, in compli-
ance with local Low Voltage Electrotechnical Regulations.
This chapter details the relevant requirements for locating and
SLC CUBE4
wiring the
its own location and installation particularities, the purpose of
this chapter is not to provide precise step-by-step instructions,
rather it should be used as a guide for the general procedures and
practices to be observed by
and defined in the EK266*08 safety instructions).
Unless indicated otherwise, all actions, indications, premises,
notes, etc. are applicable to the SLC CUBE4 units, whether or not
they form part of a parallel system.
5.1. RECEPTION.
All cabinets are supplied on wooden pallets that are mechani-
cally attached to them, with cardboard or wooden packaging
according to the model. Although the risk of tipping is minimal,
they must be handled with care, especially the taller cabinets
and when there is a slope.
It is dangerous to handle the unit on the pallet in a
•
careless manner, as it could tip and cause serious or
very serious injuries to the operators, resulting from impact
due to it possibly tipping over and/or operators becoming
trapped. Pay attention to section 1.2.1. of the safety in-
structions -EK266*08- in all matters relating to the han-
dling, moving and positioning of the unit.
Use the most suitable means for moving the UPS when it is still
packed, with a pallet truck or forklift.
Any handling of the unit must be done paying attention to the
weights indicated in "Annex III. Technical specifications" ac-
cording to the model.
5.1.1. Reception, unpacking and contents
Reception. Check that:
•
The information on the label attached to the packaging
ˆ
corresponds to the information specified in the order.
Once the UPS is unpacked, check the above information
with the information on the unit's name plate.
If there are any discrepancies, deal with the non-con-
formity as soon as possible, citing the unit's manufac-
turing number and the references on the delivery note.
It has not suffered any mishap during transport (pack-
ˆ
aging and impact indicator in perfect condition).
Otherwise, follow the protocol indicated on the label at-
tached to the impact indicator, located on the packaging.
20
7.5-20 kVA UPS series. As each site has
qualified
staff (figure recognised
Unpacking
•
To check the contents, the packaging must be removed.
ˆ
Complete the unpacking according to the proce-
dure in section 5.1.3.
Contents
•
UPS:
The unit itself.
ˆ
The user manual in electronic format
ˆ
1 RJ45 cable for connection with the Nimbus commu-
ˆ
nication card.
In the case of a parallel system, a set of parallel cables.
ˆ
Battery cabinet:
Battery connection bundle.
ˆ
Three battery fuses to be installed in the fuse holder
ˆ
disconnect switch.
Once the reception process is complete, the UPS should be
repacked until it is started up in order to protect it against me-
chanical shock, dust, dirt, etc.
5.1.2. Storage
The unit must be stored in a dry, well-ventilated area, protected
from rain, dust, splashes of water or chemical agents. It is
recommended to keep each unit in its original packaging, as it
has been specifically designed to ensure maximum protection
during transport and storage.
For units that contain Pb-Ca batteries, the charging periods
indicated in Tab. 2 of document EK266*08 must be ob-
served, as well as the storage temperature to which they are ex-
posed, otherwise the warranty may be invalidated.
Data label for the model.
MUY IMPORTANTE PARA LA VIDA DE LAS BATERÍAS DE Pb-Ca:
su degradación deben ser recargadas en los intervalos indicados. Respetar
el procedimiento referido en el manual de usuario del equipo.
VERY IMPORTANT FOR THE LIFETIME OF Pb-Ca BATTERIES:
their degradation, they must be recharged according to the stated interval
times. Respect the procedure referred in the equipment user's manual.
Fecha carga /
Charging date :
**-**-****
Factory charging date noted.
Space to note the new charging date.
Fig. 18. Label on the packaging of the battery unit.
After this period, connect the unit to the mains together
•
with the battery unit, if applicable, start it according to the
instructions described in this manual and charge for 12
hours.
[Pen
Drive].
Para evitar
ºC
Meses /
Months
In order to avoid
0 - 20
12
21 - 30
9
31 - 40
5
41 - 50
2,5
Fecha recarga /
Recharging date:
DY933B00 - 401AF000001
SALICRU
Advertisement
Table of Contents
