Installation - Salicru SLC X-PERT Series User Manual

5. INSTALLATION.

Read and observe the Safety Information described
•
in Chapter 2 of this document. Failure to observe the
instructions described in this manual could result in serious
injury to personnel in direct contact or close by or faults in
the device and/or loads connected to it.
In addition to the device's own user manual, other documents
•
are supplied on the CD-ROM or documentation pen drive.
Consult them and strictly follow the indicated procedure.
Unless otherwise indicated, all actions, instructions, guide-
•
lines and notes are applicable to all possible devices and
configurations.
5.1. RECEPTION OF THE DEVICE.
It is dangerous to handle the device on the pallet, as it could
•
overturn and cause serious impact injuries to operators
and/or entrapment. Pay attention to section 1.2.1 of the
EK266*08 safety instructions in all matters relating to the
handling, movement and siting of the unit, as well as the
relevant sections of this document.
Use the most suitable means to move the UPS while it is
•
packed, such as a pallet jack or forklift.
Any handling of the device must be carried out in accordance
•
with the weights shown in the technical specifications
according to the model, indicated in Chapter '9. Annexes'.
5.1.1. Reception, unpacking and contents.
Reception. Check that:
•
The information on the label affixed to the packaging
ˆ
relates to that specified on the order. Once the UPS
is unpacked, check the above-mentioned information
against that on the nameplate. If there are discrepancies,
report the issue as soon as possible, citing the device's
manufacturing number and delivery note references.
It has not suffered any mishaps during transportation
ˆ
(packaging and impact indicator in perfect condition).
Otherwise, follow the protocol indicated on the label at-
tached to the impact indicator, located on the packaging.
Unpacking.
•
To check the contents, it will be necessary to remove
ˆ
the packaging.
Complete the unpacking according to the procedure in
section 5.1.3.
SLC X-PERT device contents:
•
UPS with the corresponding power.
ˆ
Wiring necessary for installation.
ˆ
Warranty.
ˆ
Once the reception is completed, it is advisable to re-pack
the UPS until it is put into service in order to protect it
against mechanical shock, dust, dirt, etc.
The packaging of the device consists of a wooden pallet,
•
cardboard or wooden box, depending on the item, expanded
polystyrene corners, polyethylene cover and strapping, all
of which are recyclable materials. When the packaging
requires disposal, it must be carried out in accordance with
current laws. We recommend keeping the packaging for at
least 1 year.
USER MANUAL
5.1.2. Storage.
The device should be stored in a dry, ventilated location
•
protected from rain, dust, water splashes and chemical
agents. It is advisable to keep each device and battery unit
in its original packaging, as it has been specifically designed
to ensure maximum protection during transportation and
storage.
For devices that contain Pb-Ca batteries, the charging times
•
indicated in Tab. 2 of document EK266*08 regarding the
temperature to which they are exposed, must be respected,
otherwise the warranty may be invalidated.
After this period, connect the device to the mains together
•
with the battery unit if applicable, start it according to the
instructions described in this manual and charge for at least
12 hours.
In parallel systems, it is not necessary to interconnect
•
devices before battery charging. Each of them can be
treated independently to charge them.
Then shut down the device, disconnect it and store the UPS
•
and batteries in their original packaging, noting the new
date for recharging the batteries on a document as a record
or even on the packaging itself.
Do not store the devices where the ambient temperature
•
exceeds 50 °C or drops below -15 °C, as this may cause
degradation of the electrical characteristics of the batteries.
Special environmental conditions
It is necessary to implement specific protective
measures in case of unusual environmental conditions:
Noxious smoke, dust, abrasive dust.
–
Humidity, vapour, salty air, bad weather or leakage.
–
Explosive dust and gas mixtures.
–
Extreme variations of temperature.
–
Poor ventilation.
–
Conductive or radiant heat from other sources.
–
Fungi, insects, parasites.
–
5.1.3. Unpacking.
The packaging of the device consists of a cardboard box,
•
expanded polystyrene (EPS) or polyethylene foam (EPE)
corners, polyethylene cover and strapping, all of which are
recyclable materials; consequently, if it requires disposal,
it must be carried out in accordance with current laws. We
recommend keeping the packaging in case it needs to be
reused.
Proceed as follows:
•
Cut the straps around the cardboard box.
ˆ
Remove the accessories (cables, brackets, etc.).
ˆ
Remove the device or battery module from the box with
ˆ
the help, if necessary, of a second person depending
on the weight of the model or using appropriate
mechanical means.
Remove the protective corners from the device and the
ˆ
plastic bag.
Do not leave the plastic bag within the reach of
children to avoid the danger of suffocation.
Inspect the device before proceeding and, in the event
ˆ
of finding damage, contact the supplier or, failing that,
our firm.
X-PERT UNINTERRUPTIBLE POWER SUPPLIES (UPS)
15