Mitsubishi Electric 800 Series Instruction Manual page 414

Pr. Name
738 Second motor induced voltage constant (phi f)
739 Second motor Ld decay ratio
740 Second motor Lq decay ratio
Second motor starting resistance tuning
741
compensation coefficient 1
742 Second motor magnetic pole detection pulse width 2A
743 Second motor maximum frequency
744 Second motor inertia (integer)
745 Second motor inertia (exponent)
746 Second motor protection current level
759 Parameter for manufacturer setting. Do not set.
774 Operation panel monitor selection 1
775 Operation panel monitor selection 2
776 Operation panel monitor selection 3
779 Operation frequency during communication error
791 Acceleration time in low-speed range
792 Deceleration time in low-speed range
800 Control method selection
801 Output limit level
Constant output range torque characteristic
803
selection
804 Torque command source selection
805 Torque command value (RAM)
806 Torque command value (RAM, EEPROM)
807 Speed limit selection
808 Speed limit
809 Reverse-side speed limit
810 Torque limit input method selection
811 Set resolution switchover
812 Torque limit level (regeneration)
813 Torque limit level (3rd quadrant)
814 Torque limit level (4th quadrant)
815 Torque limit level 2
816 Torque limit level during acceleration
817 Torque limit level during deceleration
820 Speed control P gain 1
821 Speed control integral time 1
822 Speed setting filter 1
Torque control P gain 1 (current loop proportional
824
gain)
Torque control integral time 1 (current loop integral
825
time)
826 Torque setting filter 1
830 Speed control P gain 2
831 Speed control integral time 2
832 Speed setting filter 2
Torque control P gain 2 (current loop proportional
834
gain)
Torque control integral time 2 (current loop integral
835
time)
836 Torque setting filter 2
849 Analog input offset adjustment
850 Brake operation selection
853 Speed deviation time
858 Terminal 4 function assignment
Instruction
*1
code
26 A6 7 × ×
27 A7 7 × ×
28 A8 7 × ×
29 A9 7 × ○
AA 7 × ×
2B AB 7 × ×
2C AC 7 × ×
2D AD 7 × ×
2E AE 7 × ×
4A CA 7 ○ ○
4B CB 7 ○ ○
4C CC 7 ○ ○
4F CF 7 ○ ○
5B DB 7 × ×
5C DC 7 × ×
00 80 8 ○ ○
01 81 8 × ×
03 83 8 × ×
04 84 8 × ×
05 85 8 × ×
06 86 8 × ×
07 87 8 × ×
08 88 8 × ×
09 89 8 × ×
0A 8A 8 × ×
0B 8B 8 × ×
0C 8C 8 × ×
0D 8D 8 × ×
0E 8E 8 × ×
0F 8F 8 × ×
10 90 8 × ×
11 91 8 × ×
14 94 8 × ×
15 95 8 × ×
16 96 8 × ×
18 98 8 × ×
19 99 8 × ×
1A 9A 8 × ×
1E 9E 8 × ×
1F 9F 8 × ×
20 A0 8 × ×
22 A2 8 × ×
23 A3 8 × ×
24 A4 8 × ×
31 B1 8 ○ ○
32 B2 8 × ×
35 B5 8 × ×
3A BA 8 ○ ○
17.3 Parameters (functions) and instruction codes under different control methods
*2
Control method
Sensorless Sensorless Sensorless PM PM PM
× × ○
× × ○
× × ○
○ ○ ○
× × ○
× × ○
○ × ○
○ × ○
× × ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
× × ○
× × ○
○ ○ ○
○ ○ ×
○ ○ ×
× ○ ×
× ○ ×
× ○ ×
× ○ ×
× ○ ×
× ○ ×
○ × ○
○ × ○
○ × ○
○ × ○
○ × ○
○ × ○
○ × ○
○ × ○
○ × ○
○ × ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ × ○
○ × ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ×
× × Δ
○ ○ ○
Parameter
11
12
× ○
× ○
13
× ○
× ○
× ○
14
○ ○
○ ○
○ ○
15
○ ○
○ ○
○ ○
16
○ ○
○ ○
○ ○
17
○ ○
○ ○
○ ○
○ ○
18
○ ○
○ ○
○ ○
19
○ ○
○ ○
○ ○
20
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
× ○
413
17. Appendix