Mitsubishi Electric 800 Series Instruction Manual page 190

Command
Condition
interface
Pr.551 = "3, 9999"
USB
connector
Other than the
above
Pr.550 = "0, 9999"
Option
Other than the
above
Pr.550 = "5" or
Pr.550 = "9999"
(communication
option is not
installed)
Ethernet
connector
Other than the
above
External
control
—
circuit
terminal
○: Controllable, ×: Uncontrollable, Δ: Partially controllable, —: No function
*1 Operation when the enclosure surface operation panel (FR-PA07) is used.
*2 RS-485 communication via PU connector
*3 Only PU stop is enabled. "PS" is displayed on the operation panel during PU stop. The operation follows the Pr.75 Reset selection/
disconnected PU detection/PU stop selection setting. (Refer to
*4 The operation follows the Pr.338 Communication operation command source and Pr.339 Communication speed command source
settings. (Refer to page
*5 Writing of some parameters may be disabled by the Pr.77 Parameter write selection setting and the operating condition. (Refer to
Item
PU
operation
Operation command
○
(start, stop)
Frequency setting ○
Monitor ○
*5
Parameter write
○
Parameter read ○
Inverter reset ○
Operation command
×
(start, stop)
Frequency setting ×
Monitor ○
*6
Parameter write
×
Parameter read ○
Inverter reset ○
Operation command
×
(start, stop)
Frequency setting ×
Monitor ○
*6
Parameter write
×
Parameter read ○
Inverter reset ×
Operation command
*6
×
(start, stop)
*6
Frequency setting
×
Monitor ○
*6
Parameter write
×
Parameter read ○
*6
Inverter reset
×
Operation command
×
(start, stop)
Frequency setting ×
Monitor ○
*6
Parameter write
×
Parameter read ○
Inverter reset ×
Operation command
×
(start, stop)
Frequency setting ×
Monitor ○
Parameter write ×
Parameter read ○
Inverter reset ×
Operation command
×
(start, stop)
Frequency setting ×
Inverter reset ○
185.)
9.3 Start command source and frequency command source during communication operation
Controllability in each operation mode
Combined Combined
External operation operation
operation mode 1 mode 2
(Pr.79 = "3") (Pr.79 = "4")
× × ○
× ○ ×
○ ○ ○
*6
○ ○
×
○ ○ ○
○ ○ ○
× × ×
× × ×
○ ○ ○
*6 *6 *6
× × ×
○ ○ ○
○ ○ ○
× × ×
× × ×
○ ○ ○
*6 *6 *6
× × ×
○ ○ ○
× × ×
*6 *6 *6
× × ×
*6 *6 *6
× × ×
○ ○ ○
*6 *6 *6
× × ×
○ ○ ○
*6 *6 *6
× × ×
× × ×
× × ×
○ ○ ○
*6 *6
×
× ×
○ ○ ○
× × ×
× × ×
× × ×
○ ○ ○
× × ×
○ ○ ○
× × ×
○ ○ ×
*8
○ ○
Δ
○ ○ ○
page 128.)
9. (D) Operation Command and Frequency Command
NET
operation
NET
(when the
operation
PU/Ethernet
(via option)
connector
is used)
× ×
× ×
○ ○
*6 *6
× ×
○ ○
○ ○
× ×
× ×
○ ○
*6 *6
× ×
○ ○
○ ○
*4
—
○
*4
—
○
○ ○
*5
—
○
○ ○
*6
○
×
*6
—
×
*6
—
×
○ ○
— ○
○ ○
*6
—
×
○ —
○ —
○ ○
*5
—
○
○ ○
*7
—
○
— ×
— ×
○ ○
*6
—
×
○ ○
— ×
*4 *4
× ×
*4 *4
× ×
○ ○
page 135.)
189
1
2
3
4
5
6
7
8
9
10