Mitsubishi Electric 800 Series Instruction Manual page 252

• The signals can be output via communication, or assigned to the extension terminals of the plug-in option (FR-A8AY or
FR-A8AR).
External output terminal
Terminal
Pr.
name
FR-E800
190 RUN ○
191 FU ○
192 A,B,C ○
193 NET Y1 —
194 NET Y2 —
195 NET Y3 —
196 NET Y4 —
313 DO0 —
314 DO1 —
315 DO2 —
316 DO3 —
317 DO4 —
318 DO5 —
319 DO6 —
320 RA1 —
321 RA2 —
322 RA3 —
○: Assignment/output available, ─: Assignment/output unavailable (no function)
*1 The communication protocol affects which terminal can be used. For details, refer to the Instruction Manual (Communication) or the Instruction
Manual of the communication option.
*2 Refer to the Instruction Manual of the option for details on the option output terminals.
 Output signal list
• A function listed below can be set to each output terminal.
• Refer to the following table and set the parameters. (0 to 99, 200 to 299: Positive logic, 100 to 199, 300 to 399: Negative
logic)
Setting
Signal
Positive Negative
name
logic logic
0 100 RUN
1 101 SU
3 103 OL
4 104 FU
7 107 RBP
8 108 THP
11 111 RY
12 112 Y12
13 113 Y13
(physical terminal)
communication
FR-E800-E
— ○
— ○
○ ○
— ○
— ○
— ○
— ○
— ○
— ○
— ○
— —
— —
— —
— —
— —
— —
— —
Function
Output during operation when the inverter
Inverter running output frequency reaches Pr.13 Starting
frequency or higher.
Output when the output frequency reaches
*1
Up to frequency
the set frequency.
Output while the stall prevention function
Overload warning
works.
Output when the output frequency reaches
Output frequency
the frequency set in Pr.42 (Pr.43 during
detection
reverse rotation) or higher.
Regenerative brake Output when the regenerative brake duty
prealarm reaches 85% of the setting of Pr.70.
Output when the cumulative electronic
thermal O/L relay value reaches 85% of the
Electronic thermal O/L
trip level. (The electronic thermal O/L relay
relay pre-alarm
function (E.THT/E.THM) is activated when
the value reaches 100%.)
Output when the reset process is completed
after powering ON the inverter or when the
Inverter operation ready
inverter is ready to start operation with the
start signal ON or during operation.
Output when the output current is higher
Output current detection than the Pr.150 setting for the time set in
Pr.151 or longer.
Output when the output current is lower than
Zero current detection the Pr.152 setting for the time set in Pr.153
or longer.
Option output terminal (physical
Output via
terminal)
*1
FR-A8AY
—
—
—
—
—
—
—
○
○
○
○
○
○
○
—
—
—
Operation
11. (M) Item and Output Signal for Monitoring
*2
FR-A8AR
—
—
—
—
—
—
—
—
—
—
—
—
—
—
○
○
○
Related
Refer to page
parameter
— 254
Pr.41 257
Pr.22, Pr.23,
214
Pr.66, Pr.154
Pr.42, Pr.43 257
Pr.70 386
Pr.9 198
— 254
Pr.150, Pr.151 260
Pr.152, Pr.153 260
11.6 Output terminal function selection
11
12
13
14
15
16
17
18
19
20
251