Mitsubishi Electric 800 Series Instruction Manual page 32

 Simple mode parameters (Ethernet model)
Pr.
Pr. Name
group
0 G000 Torque boost
1 H400 Maximum frequency 0.01 Hz
2 H401 Minimum frequency 0.01 Hz
3 G001 Base frequency
Multi-speed setting
4 D301
(high speed)
Multi-speed setting
5 D302
(middle speed)
Multi-speed setting
6 D303
(low speed)
7 F010 Acceleration time
8 F011 Deceleration time
H000 Electronic thermal
9
C103 O/L relay
Operation mode
79 D000
selection
Terminal 2
125 T022 frequency setting
gain frequency
Terminal 4
126 T042 frequency setting
gain frequency
User group read
160 E440
selection
DO0 output
313 M410
selection
DO1 output
314 M411
selection
DO2 output
315 M412
selection
Communication
349 N010
reset selection
Frequency
541 N100 command sign
selection
CC-Link extended
544 N103
setting
PM parameter
998 E430
initialization
*9
Initial value
Increment
Gr.1 Gr.2
*1
6%
*2
5%
*3
0.1% 0% to 30%
4%
*4
3%
*5
2%
120 Hz 0 to 120 Hz
0 Hz 0 to 120 Hz
0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
0.01 Hz 30 Hz 0 to 590 Hz
0.01 Hz 10 Hz 0 to 590 Hz
*6
5 s
0.1 s 0 to 3600 s
*7
10 s
*6
5 s
0.1 s 0 to 3600 s
*7
10 s
Inverter rated
0.01 A 0 to 500 A
*8
current
1 0 0 to 4, 6, 7
0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
0.01 Hz 60 Hz 50 Hz 0 to 590 Hz
1 0 0, 1, 9999
1 9999
Refer to
1 9999
228.
1 9999
1 0 0, 1
1 0 0, 1
0, 1, 12, 14,
1 0
18, 24, 28
0, 8009,
1 0 8109, 9009,
9109
Range Application
Set this parameter to obtain a higher starting
torque under V/F control. Also set this when a
loaded motor cannot be driven, the warning
"OL" occurs, and the inverter output is shut off
with the fault indication "E.OC1".
Set the upper limit for the output frequency.
Set the lower limit for the output frequency.
Set this parameter when the rated motor
frequency is 50 Hz. Check the rating plate of
the motor.
Pre-set the speeds that will be switched
among by terminals.
Set the acceleration time.
Set the deceleration time.
Protects the motor from heat. Set the rated
motor current.
Select the start and frequency command
sources.
Change the frequency at the maximum
potentiometer setting (5 V in the initial
setting).
Change the frequency at the maximum
current input (20 mA in the initial setting).
This function restricts the parameters that are
read by the operation panel and parameter
unit.
Set this parameter to assign the functions to
page
the devices RX9 to RXB for the CC-Link IE
TSN and CC-Link IE Field Network Basic.
Disable an error reset command given via
communication in the External operation
mode or the PU operation mode.
Set this parameter to make the start
command (forward/reverse rotation) inverted
by adding a plus or minus sign to the value of
the frequency command sent through the CC-
Link IE TSN or the CC-Link IE Field Network
Basic.
Set this parameter to extend the function of
the remote registers for the CC-Link IE TSN or
the CC-Link IE Field Network Basic.
Select the PM sensorless vector control and
set the parameters that are required to drive a
PM motor.
2.4 Frequently-used parameters (simple mode parameters)
1
Refer
to
page
2
374
3
211
4
376
5
34,
39,
195
6
7
158
198
8
174
9
41,
273
43,
10
273
90
*10
*10
*10
*10
90
31
2. Basic Operation