Yamaha F225F Service Manual page 559

Reducing the fuel pressure .........................6-6
Refacing the valve seat.............................7-59
Registering the receiver ID to the ECM ....3-12
Removing the canister ..............................6-26
Removing the clamp bracket ....................9-27
Removing the cowling lock lever.................9-5
Removing the cylinder head .....................7-55
Removing the drive shaft .................8-23, 8-78
Removing the driven sprocket and
camshaft .................................................7-45
Removing the engine ECM .......................7-33
Removing the flushing hose........................9-5
Removing the flywheel magnet.................7-15
Removing the forward gear.......................8-23
Removing the fuel filter assembly .............6-11
Removing the fuel injector ........................6-44
Removing the intake manifold...................6-15
Removing the intake silencer....................6-15
Removing the junction box........................7-28
Removing the knock sensor......................7-72
Removing the lower unit ... 8-3, 8-8, 8-64, 8-67
Removing the low-pressure fuel pump .....6-30
Removing the oil cooler ............................7-66
Removing the oil filter bracket...................7-66
Removing the oil pump assembly .............7-66
Removing the power unit ............................7-8
Removing the propeller shaft housing
assembly........................................8-16, 8-73
Removing the PTT motor..........................9-40
Removing the PTT switch ...........................9-9
Removing the PTT unit .............................9-32
Removing the pulley bracket.....................7-72
Removing the Rectifier Regulator .............7-28
Removing the reservoir.............................9-40
Removing the reverse gear.......................8-78
Removing the shift actuator assembly ......7-35
Removing the shift rod and SPS.................9-2
Removing the starter motor .............5-58, 7-31
Removing the steering arm.......................9-23
Removing the thermostat..........................7-72
Removing the throttle body and
surge tank ...............................................6-22
Removing the tilt ram ................................9-53
Removing the timing belt ..........................7-38
Removing the trim ram..............................9-53
Removing the upper case .........................9-12
Removing the vapor separator..................6-35
Removing the water pump and
shift rod ..........................................8-11, 8-70
Removing the wiring harness....................7-18
Replacing the OCV filter .........................10-12
Replacing the oil filter................................10-9
Replacing the timing belt.........................10-14
Replacing the valve guide.........................7-57
Reverse gear shim (T1) selection
table........................................................ 8-97
Reverse gear shim (T2) selection chart.... 8-59
Rigging grommet description ...................... 3-8
Rigging grommet mounting ........................ 3-8
Rigging information................................... 1-26
Rigging recommendations........................ 3-30
Rotating part ............................................... 0-1
S.
Safety while working................................... 0-1
Selecting the crankpin bearing ................. 7-83
Selecting the crankshaft journal
bearing.................................................... 7-87
Selecting the pinion shim (T3) ......... 8-43, 8-88
Selecting the propeller shaft
shim (T4) ....................................... 8-61, 8-88
Selection................................................... 3-32
Self-protection ............................................ 0-2
Sensor, switch, and actuator ...................... 2-3
Sensor,switch ........................................... 2-21
Serial number ............................................. 1-2
Shift actuator ................................... 1-13, 7-34
Shift rod and SPS ....................................... 9-1
Shim location ................................... 8-42, 8-87
Shimless valve lifter .................................. 2-24
Shimming......................................... 8-42, 8-87
Shimming (counter rotation model) .......... 8-81
Shimming (regular rotation model) ........... 8-36
Shimming check sheet .................... 8-37, 8-82
Shimming workflow.......................... 8-36, 8-81
Single outboard motor application ............ 3-21
Skip-firing control...................................... 2-13
Sleeveless cylinder................................... 2-24
Special service tool.............................. 0-3, 0-9
Specified tightening torque ....................... 1-26
Starboard........................................... 5-2, 5-10
Starter motor.................................... 5-56, 7-30
Starting system ......................................... 1-14
Starting units and component................... 5-53
Stationary test............................................. 4-2
Steering arm ............................................. 9-22
Symbol........................................................ 0-7
Synchronous fuel injection.......................... 2-6
T.
Test run .................................................... 10-6
Throttle body............................................. 6-20
Tightening torque........................................ 0-3
Timing belt ................................................ 7-37
Top .................................................... 5-7, 5-15
Triple outboard motor application ............. 3-26
Trouble code and checking step................. 4-8
Index
0
1
2
3
5
6
7
8
9
10
10
A
i-6