Adjusting The Rear Brake Lock Cable - Yamaha TMAX XP530E-A 2017 Service Manual

throttle grip or handlebar grip.
h. Tighten the bleed screw and then release the
brake lever.
i. Repeat steps (e) to (h) until all of the air bub-
bles have disappeared from the brake fluid in
the plastic hose.
j. Check the operation of the hydraulic unit. Re-
fer to "HYDRAULIC UNIT OPERATION
TEST" on page 4-75.
ECA25780
NOTICE
Before checking the operation of the hydrau-
lic unit, always push the OFF/LOCK switch.
k. After operating the ABS, repeat steps (e) to
(i), and then fill the brake master cylinder
reservoir to the proper level with the speci-
fied brake fluid.
l. Tighten the bleed screw to specification.
Front brake caliper bleed screw
5 N·m (0.5 kgf·m, 3.7 lb·ft)
Rear brake caliper bleed screw
6 N·m (0.6 kgf·m, 4.4 lb·ft)
m. Fill the brake master cylinder reservoir to the
proper level with the specified brake fluid.
Refer to "CHECKING THE BRAKE FLUID
LEVEL" on page 3-15.
EWA13110
WARNING
After bleeding the hydraulic brake system,
check the brake operation.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
EAS31425
ADJUSTING THE REAR BRAKE LOCK
CABLE
EWA18100
WARNING
Do not use the rear brake lock lever while
driving.
TIP
Place the vehicle on the centerstand.
1. Measure:
• Rear brake lock cable length "a"
Out of specification  Adjust.
TIP
Measure while the rear brake lock lever is re-
leased.
Rear brake lock cable length
43–45 mm (1.69–1.77 in)
PERIODIC MAINTENANCE
2. Adjust:
• Rear brake lock cable length
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Turn the rear brake lock cable adjusting nut
"1" in direction "b" or "c" until the specified
rear brake lock cable free play is obtained.
Direction "b"
Rear brake lock cable length increased.
Direction "c"
Rear brake lock cable length decreased.
b
c
1
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3. Adjust:
• Clearance between the brake pad and brake
disc.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the cap of the rear brake lock adjust-
ing nut.
b. Loosen the rear brake lock adjusting nut "1"
slightly.
c. Adjust the piston adjusting bolt "2" so that the
wear indicator "3" is placed within the width of
the wear indicator groove "4" when the rear
brake lock is activated.
Recommended procedure:
Tighten the piston adjusting bolt to 3.0 N·m
(0.30 kgf·m, 2.2 lb·ft) and then loosen the bolt
1–1/2 turn.
d. Tighten the rear brake lock adjusting nut
while holding the piston adjusting bolt so as
not to turn the bolt.
3-18
a