Avaya IX Collaboration Unit CU360 Release Notes page 81

© 2019 Avaya Inc. All rights reserved
Category
In a Call
Release Notes for Avaya IX Collaboration Unit CU360
Case Number/
Description of issue
Ticket ID
the Avaya endpoint is
configured with AES256.
The Avaya endpoint doesn't
QC#26789 display the message to be in call
JIRA-57114 hold when Flare iPad is put in
hold
Using Polycom MGC50 (v
QC#2766 8.0.2.6) sometimes H.239
presentation does not function.
Polycom diagnostics incorrectly
QC#2981
identifies Avaya endpoints.
Incident #16384-10505: Remote
camera switch from HDX to
QC#11493 Avaya endpoint and reverse is
not performed. Issue reported
to Polycom.
Cisco C20 cannot control the
QC#2964 Avaya endpoint camera in H.323
calls.
Polycom MGC systems (v9.0)-
Avaya endpoint does not receive
the video stream when it is
QC#6665
connected to MGC with default
settings (reference Pivotal
#16384-7589).
LifeSize Express LS_EX1_3.0.7 (2)
produces corrupted audio in SIP
calls with audio coding based on
QC#5567 G.722.1 Annex C, 48 kHz.
Avaya endpoint cannot establish
incoming point-to-point SIP calls
if H.264 coding is used.
IOT issue with Tandberg/CISCO
QC#16828 MXP1500.
Reported to Tandberg/Cisco.
The Tandberg/CISCO MXP1500
does not send video to the as
QC#17464
soon as a call is started.
Reported to Tandberg/Cisco.
Avaya 10x0(LifeSize) v4.8 issue.
Avaya Integration Rad #57
[XT/SIP]: An Avaya XT Series or
QC#16857 CU-360 endpoint registered with
SIP cannot share content (via
BFCP) with Avaya 1000-series
endpoints.
If Avaya endpoint is configured
RVSM-5252 with a Unicode name, the ECS
rejects the H.323 call
Tandberg MXP Series
QC#26201 interoperability issue when
placing SIP TLS calls.
Presentation, sent in WCS mode
from an Avaya endpoint, is sent
RVELITE-6045
black from AMS to other Codec
Units (not in WCS mode)
When connecting to Polycom
RealPresence Immersive Studio
Flex 6.1.2_06 the remote party
does not receive audio. This is
due to wrong capability
management on the Polycom
side.
You cannot dial a recent
QC#9510 incoming ISDN number from the
Recent Calls list.
Before making an ISDN voice-
QC#9509
only call, you need to first
Solution/Workaround
For low bit rate calls (up to 256Kbits), set the
maximum call rate of the Codec Unit to 2M (the
same max. rate as MGC) in the Administrator
Settings > Call Preferences page.
For 384Kbit- 2Mbit calls: In the MGC Advanced
Properties page, deselect Auto Video Bit Rate.
Update LifeSize Express to latest version. As a
temporary alternative, disable G.722.1 from the
web interface by navigating to Administrator
Settings > Calls > Preferences > Audio
Disable H.264 High Profile on the Codec Unit.
Configure > Advanced > Preferences > Video
Disable H.264 High Profile on the endpoint.
Upgrade Avaya 1000-series endpoints to version 4.9
or higher.
Use a plain ASCII name for the Codec Unit.
Configure > Advanced > Protocols > SIP > TLS >
Enabled =No.
Disable G.719 on the Codec Unit.
Dial the ISDN number manually.
To make an ISDN Voice-Only call, perform the
following procedure:
Known Issues 21