Piper Navajo PA-31 Service Manual page 9

PIPER NAVAJO SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont.)
Figure
8-9.
8-10.
8-11.
8-12.
8-13.
8-14.
8-15.
8-16.
8-17.
8-18.
8-19.
8-20.
8-21.
8-22.
8-23.
8-24.
8-25.
8-26.
8-27.
8-28.
8-29.
8-30.
8-31.
8A-1.
8A-2.
8A-3.
8B-1.
8B-2.
8B-3.
8B-4.
8B-5.
8B-6.
8B-7.
8B-8.
8B-9.
8B-10.
8B-11.
8B-12.
8B-13.
8B-14.
8B-15.
8B-16.
8B-17.
8B-18.
Fuel-Air Bleed Nozzle ....................
Contact Points .........................
Rotor Holding Tool Installed ................
Timing Kit Installed ......................
Aligning Timing Marks Single Contact Assembly Magneto
Forming Leads in Breaker Compartment ..........
Engine Timing Marks .....................
Magneto Timing Marks ....................
Removing Spring From Lead Assembly
..........
Assembly Tool .........................
Using Assembly Tool .....................
Measuring Lead Assembly Length ..............
Cutting Metallic Braid From End of Lead .........
Unbraiding Metallic Shielding ................
Forming Shielding Around Ferrule .............
Ferrule Seating Tool .....................
N eedle . .. ... . .............. . ......
Measuring Wire From Top of Ferrule ............
Installing Grommet Over Lead Assemblies .........
Lead Assembly Installed in Grommet .....
......
Wire Doubled Over for Installation of Eyelet .......
Ignition System Schematic (PA-31 Turbo) .........
Removing Frozen Spark Plug ................
Propeller Governor ......................
Engine Installation ......................
Fuel-Air Bleed Nozzle ....................
Engine Installation ......................
Height of Spring in Distributor Block Tower .......
Contact Points .........................
Engine Timing Marks ......................
Timing Light Connected to Magneto ............
Timing Marks on Magneto Rotor .......
Painted Tooth Centered in Timing Window ........
Timing Mark on Rotor Aligned with Pointer (Right-Hand Rotation)
Timing Light Connected to Magneto ............
Timing Light Connected to Magneto and Breakers ....
Checking Harness Lead Continuity .............
Checking Harness Lead Insulation Resistance .......
Modified Pliers .........................
Removing Spring From Lead Assembly ..........
Assembly Tool .........................
Using Assembly Tool .....................
Ferrule Positioned Under Braid ...............
Ferrule Seating Tool 11-7074 ................
Rotation)
Aerofiche
Grid No.
. . . . . . . .. . . . . . . 2118
...............
2120
............... 2122
..........
..... 2122
.......... .... . 2I23
. ......
... .. . ..
2124
. ... .. . .. . . . . ..
2Jl
. ..... . ... ... .. 2J1
. .. . . . . . . . . . . . . 2J3
. ...
.. . .. . . . . .. 2J4
. ..... . ... .. . . .2J4
...............
2J4
. ...
... ... ... . . 2J5
............... 2J5
. .. . ...
... .. . . . 2J6
...............
2 J6
. .. . . . . .. . . . . . . 2J6
. .. . ... ... .. . . . 2J7
. .. . ... ... .. . . .2J7
. .. . ... .. . . . . . . 2J8
. .. . ...
. .. .. . . . 2J8
. . .. . . . . . . . . . . . 2J9
. . . . . . . . . . . . . . . 2J1l
. ............
.. 2K 12
. ...... ... ..... 2K 13
. ......... ..... 2K 16
...............
2K23
. . . . . . . . . . . . ... 2L1
. . . . . . . . . . . . . . . 2L2
. . . . .. . . . . . . . .
. 2 L4
. . . . .. . . . . . . . . . 2L4
. .. . . . . .. . . . . . . 2L5
. . . . .. . .. . . . . . . 2L5
otation) .......... 2L7
. . . . . . . . . . . . . .. 2L7
. . . .. .. . ..... . . 2L7
. .. . .. . . . . . . . . . 2L7
. . . . . . . . . . . . . . . 2L11
. . . . . . . . . . . . . . . 2L II
. .. . .. . . . . . . . . . 2L11
. ... ... ...
. . . ..
.2L12
............... 2L14
. .. . ... ... . . . . . 2L 14
8B-19. Position of 11-8627 Kit and Contact Spring at Start of Installation
.. 2L14
Revised: 11/15/82
1A9