Piper Navajo PA-31 Service Manual page 8

PIPER NAVAJO SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont.)
Aerofiche
Figure
Grid No.
6-28.
Hydraulic System Installation ........
......................................................
2D6
6-29. Gear Actuating Cylinder (Ozone) ........................................................................................
2D8
6-3 0. Gear Actuating Cylinder (W iebel Tool)...............................................................2D10
6-31.
Gear Door Actuating Cylinder (Ozone) .......
..........................................
2D12
6-32.
Gear Door Actuating Cylinder (Wiebel Tool)......................................................15
6-33.
Hydraulic Filter .......................................................................................
2D16
6-34. Hydraulic Pum
p..............................................................................................................
2D19
6-35.
Power Pack Test Harness Schematic.....................................................................................
2D23
7-1. Nose Gear Oleo Strut Assembly ........
...........................................................
E8
7-2. Nose Landing Gear Installation...........................................
................................ 2E17
7-3. Clamping Rudder Pedals in Neutral Position.............................................................................2E22
7-4. Rudder Pedals Neutral Angle ....................................................................................
2E22
7-5. Aligning Nose Gear.
.............................................
2E22
7-6. Main Gear Oleo Strut Assembly ................................................................................................ 2 F
7-6a. Correct Method of installing Rod End Bearings ............
...............................................
2F4
7-7. Main Landing Gear Installation (Left) ............................................................................
2F7
7-8.
Actuator Cylinder Lock Installation........................................................................................... 2F
7-9.
Aligning Main Gear .......... ...............................................................................................
2F12
7-10. Landing Gear Circuit Diagram (S/N 31-2 to 31-184 Inc.) ...........................................
2F16
7-10a. Landing Gear Circuit Diagram (S/N 31-185 and up) .............................................
2F17
7-11.
Adjusting Main Gear Down Light Switch ............................................................................
2F18
7-12.
Gear Warning Switches Installation........................................... ................. 2 F20
7-13. Nose W heel Assembly ................................................................
7-14.
Main W heel Asse
m bly.....................................................................................2F24
7-15.
Brake Installation ..................................................................................................
2G
7-16. W heel Brake Assembly (30-68 and 30-68A) ...........................................
........ ...
2G3
7-16a. Removal and Installation of Anchor Bolts...............................................................................2G4
7-16b. W heel Brake Assembly (30-95 and 30-95A ......................................
2G5
7-17. Brake M aster Cylinder Assembly .............................................................................................. 2 G8
7-18. Parking Brake Valve Assembly ...........................................................................................
2G10
7-19. Bleeding Brake ...................
...........................................................................
2G I
7-19a. Nose Gear Wear Limits ..
. ......................................................................
2G12
7-19b. Main Gear Wear Limits ............................................................................................
2G16
7-20. Fabricated Tool, Checking Nose Wheel Alignment
...............................................
2H2
7-21. Fabricated Tool, Checking Nose Gear Drag Link Travel
..............................................
2H3
7-22. Fabricated Tool, Checking Main Gear Side Brace Link Travel ............................................... 2H4
7-23.
Fabricated Tool, Checking Main Gear Toe-in Adjustment ...............................................
2H5
8-1.
Engine Cowling ........................................................................................................
12
8-2.
Cowl Flap Transmission and Sender Assembly..................................................................... 2H14
8-3.
Propeller Installation .........................................................................................................
2H17
8-4.
Typical Nicks and Removal Method ...........................................................................
2H18
8-5.
Propeller Governor ...................................................................................................
2H22
8-6.
Engine Installation.......................................................................................211
8-7.
Schematic Diagram of Turbocharger System...............................................
................. 217
8-7a. Turbocharger Installation (PA-310-325) .......
.............................................
218
8-7b. Exhaust W tegate....................................................................................................................2I11
8-8.
Fuel Injector ............................................................................................................................... 2117
Revised: 2/18/94
LANDING GEAR AND BRAKE SYSTEM
1A8