Piper Navajo PA-31 Service Manual page 100

PIPER NAVAJO SERVICE MANUAL
TABLE III-I. INSPECTION REPORT
Nature of Inspection
E. FUSELAGE AND EMPENNAGE GROUP (cont.)
12. Check hydraulic power pack fluid level. Fill as required............................................
13. Inspect hydraulic power pack and lines for damage and leaks. ...................................
14. Inspect landing gear rod or cable for corrosion and general condition ........................
15. Inspect roll pin in hydraulic power pack. (Refer to Section VI.) ................................
16. Inspect fuel lines, valves, and gauges for damage and operation. ...............................
17. Inspect forward baggage door latch and hinge operation and security. .......................
18. Inspect security of all lines.........................................................................................
19. Inspect vertical stabilizer and rudder surfaces for damage. ........................................
20 Inspect rudder and tab hinges, horns, and attachments for damage and operation......
21. Inspect security of vertical fin attachments .................................................................
22. Inspect rudder and tab hinge bolts for excess wear. ...................................................
23. Inspect rudder trim mechanism installation. (See Note 26.) .......................................
24. Inspect horizontal stabilizer and elevator surfaces for damage ....................................
25 Inspect elevator and tab hinges, horns, and attachments for damage and operation.
(See N ote 28.)..............................................................................................................
26. Inspect horizontal stabilizer attachments......................................................................
27. Inspect elevator and tab hinge bolts and bearings for excess wear. (See Note 29.) ....
28. Inspect elevator, stop screws and nuts for damage, looseness or evidence of move-
ment, proper torque of jam nuts per latest revision of Piper Service Bulletin No.
649 ....................................................................................... ....................................
29. Inspect elevator trim mechanism installation. (See Note 26.).....................................
30. Inspect elevator balance spring tension. (Refer to Service Manual, Section V, and
latest revision of Piper Service Bulletin No. 626.) .....................................................
31. Inspect primary aileron, rudder, elevator control cables and trim cables, turnbuckles,
guides, and pulleys for tension, safety, damage and operation. (See Note 26.) ..........
32. Inspect aileron, rudder, elevator rod end bearings for condition and freedom of
movement. (Refer to AD 93 24 02.) (See Note 43.)...................................................
33. Clean and lubricate elevator and rudder trim drum screws ..........................................
34. Inspect anti-collision lights for security and operation. .......................................
35. Lubricate per lubrication chart. (Refer to Service Manual, Section II.)......................
36. Inspect pneumatic and flexible lines and components for condition and operation.
(See N ote 30.)...............................................................................................................
37. Inspect condition of pneumatic deicers, if installed. ...................................................
38. Inspect security of Autopilot servo bridle cable clamps. (See Note 26.) ....................
39. Inspect air conditioning system for freon leaks............................................................
40. Inspect emergency locator transmitter battery for replacement date or time. (Refer
to Service Manual, Section XII and latest revision of Piper Service Letter No 820. ).
41. Inspect emergency locator transmitter to ensure contact separator is properly
installed. (Refer to latest revision of Piper Service Letter No. 935.) ..........................
42. Install inspection plates and panels. ............................................................................
Revised: 2/18/94
Interim Revision: 12/02/94
1E4
Inspection time (hrs)
50 100 500 1000
0 0 0 0
0
0 0
0 0 0
0 0
O0
0 0 0
0 0
0
0 0 0
00 0 0
0 0 0
0 0 0
0 0 0
0 0 0
00
0 0
0 0 0
0 0 0
0 0 0
0 O 0
O
0 0 0
000
000
0 0 0
000
0
O 0
O
O O 0
00 0
0
0
0
0 0 0
O O O
0 0 O
INSPECTION