7-10A. Landing Gear Circuit Diagram (S/N 31-185 And Up); Nose W Heel Assembly; Main W Heel Assembly; W Heel Brake Assembly (30-68 And 30-68A) - Piper Navajo PA-31 Service Manual

PIPER NAVAJO SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont.)
Aerofiche
Figure
Grid No.
6-28. Hydraulic System Installation ...............................................
D6
6-29.
Gear Actuating Cylinder (Ozone) ................................................... 2D8
6-3 0. Gear Actuating Cylinder (W iebel Tool) ......................... 2D10...........
6-31.
Gear Door Actuating Cylinder (Ozone) ..................................... 2D12.......
6-32.
Gear Door Actuating Cylinder (Wiebel Tool)
...............................................
2D
6-33.
Hydraulic Filter ................................................
2D 16
6-34.
Hydraulic Pump........................
......................................
2D19
6-35. Power Pack Test Harness Schematic..........................................................................................
7-1. Nose Gear Oleo Strut Assembly ................................................
2E8
7-2.
Nose Landing Gear Installation.......................................................................2E17
7-3.
Clamping Rudder Pedals in Neutral Position.............................................................................2E
7-4. Rudder Pedals Neutral Angle ..................................................................
7-5. Aligning Nose Gear................................................2E22
7-6.
Main Gear Oleo Strut Assembly .........
..............................................
.....
7-6a. Correct Method of installing Rod End Bearings.......................................................................2F
7-7. Main Landing Gear Installation (Left) ...........................................................
2F7
7-8.
Actuator Cylinder Lock Installaion ...............................................
2F11
7-9. Aligning Main Gear...............................................2F12
7-10.
Landing Gear Circuit Diagram (S/N 31-2 to 31-184 Inc.) ........................................
2F16
7-10a. Landing Gear Circuit Diagram (S/N 31-185 and up) ...........................................
2F17
7-11. Adjusuating Main Gear Down Light Switch .........,.................................. .....
2F18
7-12.
Gear Warning Switches Installation ..........................................................
2F20
7-13. Nose W heel Assembly ...................................................
.
2F23
7-14.
Main W heel Assembly ...............................................
2F24
2
7-15.
Brake Insallation...............................................
2GI
7-16.
W heel Brake Assembly (30-68 and 30-68A)...............................................
2G3
7-16a. Removal and Installation of Anchor Bolts.................................................................................2G
7-16b. W heel Brake Assembly (30-95 and 30-95A) ................................
.2G5
7-17. Brake Master Cylinder Assembly .................................................
2G8
7-18. Parking Brake Valve Assembly .....................................................
2G10
7-19.
Bleeding Brake ..................................................................................
7-19a. Nose GearWear Limits .....................................................................
7-19b. Main Gear Wear Limits.....................................................................2G16
7-20.
Fabricated Tool. Checking Nose Wheel Alignment......
........................................
7-21.
Fabricated Tool, Checking Nose Gear Drag Link Travel........................
....................... 2H3
7-22. Fabricated Tool, Checking Main Gear Side Brace Link Travel ..................... .......................... 2H4
7-23. Fabricated Tool, Checking Main Gear Toe-in Adjustment ........................
................
....... 2H5
8-1. Engine Cowling ..............................................................................
12
8-2. Cowl Flap Transmission and Sender Assembly.........................................................................2H 14
8-3.
Propeller Insallation .......................................................................
8-4.
Typical Nicks and Removal Method ................................................
2H18
8-5. Propeller Governor ...............................................
2H22.
8-6. Engine Insallation ............................................................................
211
8-7. Schematic Diagram of Turbocharger Sysem..............................................
217
8-7a.
Turbocharger Installation (PA-310-325) ..............................................
2I8
8-7b. Exhaust Wastegate...........................................................................................2111
8-8.
Fuel Injector ..............................................
2II7...............
Revised: 2/18/94
LANDING GEAR AND BRAKE SYSTEM
2A5