Piper Navajo PA-31 Service Manual page 6

PIPER NAVAJO SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont.)
Figure
Aerofiche
Grid No
4-13 Cargo Door.................................................
IGI
4-14.
Pilot Door..........
...............................................
1
4-15.
Aileron Balancing.1G7
4-15. Aileron Balancing .........................................................
IG7
4-16. Elevator Balancing ....
............................................
1G8
4-17
Elevator Trim Weight Installation
............................................
IG10
4-18.
Elevator Trim Weight Installation
(Without
Wing Lockers) ..................
..
.. 1G11
4-19. Elevator Trim Weight Installation
(With Wing Lockers) .........................
IGII
4-20. Elevator
Friction Measurement.........................................
1
4-21. Rudder Balancing.1G14
4-1.
Rudder Balancing
.........................................................
1G14
4-22.
Balancing Rudder
..........................................................
1G15
4-23.
Balancing Rudder
.......................................................
IG16
4-24.
Empennage and Nacelle Skin Material and Thickness
...........................
1G17
4-25 Fuselage and Wing Skin Material and Thickness ...............................
1G19
4-26.
Typical Access Holes .........
1
4-27
Installation
of Balance Weight Anchor Nut. Elevators P N 40140-00
and P N 40140-01
1G22 and P N 40140-01 ........................................................
1G22
4-28. Installation
of Balance
Weight Anchor Nut. Elevators P N 43757-00
and P N 43757-01 ..........................................
1G24
4-29
Installation
of Rudder Balance Weight Anchor Nut .............................
1H1
4-30.
Ballast Weight Lifting Handle (PA-31-300) .....................................
1H2
4-31
Surface Scratches
Abrasions
or Ground-In-Dirt
......................
....
1H7
4-32. Deep Scratches.
Shallow Nicks and Small Holes ...............
1
4-33.
Mixing of Epoxy Patching Compound
.......................................
1H8
4-34. Welding Repair Method..............................
1H8
4-35
Repairing
of Cracks....
..... .. 1H10..
...........
1
4-36.
Various Repairs ................
1H11
4-37 Repair of Stress Lines ................
1
4-38.
Repair of Impacted
Damage .................................................
1
4-39
Installation
of Radome Erosion Shield .......................
H 17
4-40
Wing,Front
Spar Attachment
Bulkhead Repair ................................
1
5-1 Control Column
Installation
.......................................
114
5-1a.
Correct Method of Installing Rod End Bearings ................................
5-2. Ailcron and Aileron Trim Controls
...........
5-3.
Installation of Bellcrank R
in Tool.......................................
1114
5-4.
Installation
of Aileron Rigging Tool ..................................
. .
111
5-5
Elevator and Eleator
Trim Contols...........................................
1121
5-6. Installation
of Elevator Rigging Tool .......................................
5-7
Elevator Travel Stops .......................................
.
1
5-
7
a. Safety Wiring Control Surface Stops ...................................
. 1124
5-8.
Methods of Blocking Trim Cables ..............
1
5-8a. Cable Routing on Elevator Trim Sero
...............................
1J4
5-9 Rudder Pedal Installation
...............................................
....
5-10.
Rudder and Rudder Trim Controls
........................................
1
5-11 Clamping
Rudder Pedals in Neutral Position ...................................
1J13
5-12.
Installation of Rudder
Rigging Tool
5-12. Installation of Rudder Rigging Tool .......................................... 1G13
5-13. Trim Screw Assembly 5-13.
Trim
Screw Assembly .......................................................
1J13
5-14. Control
Pedestal.............
1J18
Revised: 3/2/84
1A6