Nilfisk-Advance Advance Retriever 2060 Service Manual page 78

5 5 5 5 5
Mount the (3) gauges (H, I & J)
as shown.
6 6 6 6 6 (L) (L) (L)
Install the (3) (L) (L) Terminal Tabs on the Black Wires for each gauge light.
7 7 7 7 7 Install the (A, B, C, E & Q) (A, B, C, E & Q) Wire assemblies onto the gauges as shown in Figure 2, 3 or 4 (A, B, C, E & Q) (A, B, C, E & Q) (A, B, C, E & Q)
assembly (E) (E) (E) (E) be sure to connect the smaller of the two ring terminals to the Oil Pressure Gauge. When installing the wire assembly (E)
(Q) (Q) (Q) (Q) (only used on diesel machines) be sure to connect the smaller of the two ring terminals to the Water Temperature Gauge. Wiring (Q)
diagrams are also provided on the last page of this instruction sheet. Note: Wire assemblies (B)
exactly as shown in the wiring diagrams (as demonstrated in Figures 2 & 3) as long as wires are all connected to the proper terminal
of each gauge they will work.
8 8 8 8 8 Figure 2 Figure 2 Figure 2 reflects a Propane Model. A Gasoline and Dual Fuel are wired the same this is shown in Figure 3 Figure 2 Figure 2
Diesel wiring. The Black Wire (S)
must find this wire and connect it to the middle terminal (grd) of one of the new gauges from the kit.
9 9 9 9 9 Also on the propane model, the BLU/BLK Wire (T)
installed the (3) (L) (L) (L) (L) (L) Terminal Tabs and the Wire Assembly (C)
on propane models locate the VIO wire (W)
terminal of the Oil Pressure Gauge. Note: On gas, dual fuel, and diesel machines wire (W)
it should remain there.
10 10 10 10 10 (A & B) (A & B)
Wire Assemblies (A & B) (A & B) (A & B) each have (4) connectors on them. The propane model will only require that (3) of these connectors be
used on each of these assemblies because of the lack of a fuel gauge. The fourth connector on each wire can either be cut off or left
hanging loose.
11 11 11 11 11 On all models except the diesel, find the VIO/BLK Wire (U)
Receptacle Tab (K) (K) (K) (K) on it. Then connect this wire to the VIO/BLK Wire (D) (K)
12 12 12 12 12 The White Wire (E) (E) (E) should then be routed into the engine compartment and around the back of the engine so it reaches the side of (E) (E)
the engine where the oil sender is located. The WHT/BLK wire (Q)
of the engine so it reaches where the new temperature sender will be installed.
13 13 13 13 13 The control panel and console can be re-installed at this point.
FIGURE 2 FIGURE 2 FIGURE 2 FIGURE 2 FIGURE 2
(H, I & J) (H, I & J)
(H, I & J) (H, I & J) in the holes that you cut in step 3 as shown in Figure 2, 3 or 4
(S) (S) (S) from the wiring harness will not be connected to anything in the case of propane machines. You
(S)
(W) (W)
(W) from the harness, it will not be connected to anything. Connect the wire (W) (W)
Rear View of Control Panel Assembly
Propane Machines
L
S
Harness
(T) (T) from the wiring harness will not be connected to anything. Once you have (T)
(T)
(C) (C), this wire can be connected to the tab end of Wire Assembly (C) (C)
(C)
(U) (U) going to one of the indicator light connectors. Cut this wire and install the (U) (U)
(D) (D) (D) (D) previously installed on the Water Temp Gauge.
(Q) (Q) (Q) should then be routed into the engine compartment to the back (Q)
T
B
S
I
W
U
E
(page 2 of 6)
Figure 2, 3 or 4 Figure 2, 3 or 4
Figure 2, 3 or 4. Make sure the gauges are orientated Figure 2, 3 or 4
Figure 2, 3 or 4 respectively. When installing the wire Figure 2, 3 or 4 Figure 2, 3 or 4 Figure 2, 3 or 4
(B) (B) (B) (B) and (C)
Figure 3. Figure 4 Figure 3 Figure 3 Figure 3
(W) (W)
(W) (W) is already connected to the fuel gauge and
(J) ) Water Temp.
P4
I
S
(I) ) Oil Press.
L
S
I
(H) ) Volt
P5
K
4/99 revised 8/01 Form No. 56040693
(C) do not have to be wired (C) (C) (C)
Figure 4 Figure 4 shows the Figure 4 Figure 4
(C) (C) (C). Next
(C)
(W) (W) to the "I I I I I " (W)
(W)
C
L
P3
A
D