GE ALPS Instruction Manual page 355

C
C1 (Protection Setting 2019) ............................................ 2-46
C2 (Protection Setting 2020) ............................................ 2-46
CARRSTART (Protection Setting 1204) .. 1-30, 2-23, 2-33, 2-60,
2-69
CASE ................................................................................ 3-1
CASE ASSEMBLY ............................................................. 3-1
CC
see CONTACT CONVERTERS
CC1 (General Setting 501) ................................................. 2-8
CC10 (General Setting 510) ............................................... 2-8
CC11 (General Setting 511) ............................................... 2-8
CC12 (General Setting 512) ............................................... 2-8
CC2 (General Setting 502) ................................................. 2-8
CC3 (General Setting 503) ................................................. 2-8
CC4 (General Setting 504) ................................................. 2-8
CC7 (General Setting 507) ................................................. 2-8
CC8 (General Setting 508) ................................................. 2-8
CC9 (General Setting 509) ................................................. 2-8
CHANGE BUS/STATION ID ............................................ 11-12
CHANNEL RELEASE TIME
definition ....................................................................... 2-34
CHANNEL TEST .............................................................. 8-11
CIRCUIT BOARDS
bus card .......................................................................... 3-3
communications interface ................................................ 3-9
communications interface diagram ................................... 3-9
DSP/ANI board .............................................................. 3-11
i960 CPU board ............................................................. 3-12
input ........................................................................ 3-6, 3-7
local user interface logic .................................................. 3-6
locations ......................................................................... 3-3
magnetics module ........................................................... 3-3
output ............................................................................. 3-6
power supply ................................................................. 3-10
CLOSE BREAKER ............................................................. 8-9
CLOSE BREAKER 1 ........................................................ 1-19
CLOSE BREAKER 2 ........................................................ 1-19
CLOSEANG (Protection Setting 1819) ......................1-48, 2-44
CLR KEY ........................................................................... 8-2
COMMUNICATIONS ........................................................ 1-20
ALPS modem ................................................................ 8-25
ASCII command list ....................................................... 12-2
ASCII interface ......................................................8-23, 12-1
description .................................................................... 12-1
DNP 3.0 ..........................................................................C-1
interface board ................................................................ 3-9
modem connections/settings ..................................8-24, 8-25
modem connnections/settings ........................................ 8-25
null-modem connections ........................................8-23, 8-27
passwords ..................................................................... 8-21
remote communications interface ................................... 8-24
software ........................................................................ 8-23
COMPENSATED POSITIVE-SEQUENCE OVERVOLTAGE
application .................................................................... 1-44
description .................................................................... 1-44
phasor diagram ............................................................. 1-44
COMPENSATED SYSTEMS
Zone 1 ground reach setting .......................................... 2-11
Zone 1 settings ............................................................... 2-9
COMPENSATION FACTOR ................................................ 7-2
COMPORT1 (General Setting 201) ..................................... 2-4
COMPORT2 (General Setting 202) ..................................... 2-5
COMPORT3 (General Setting 203) ..................................... 2-5
CONFGTRIP (Protection Setting 810) ............................... 2-30
CONFIGURATION
GE Power Management
INDEX
outputs .......................................................................... 1-10
CONFOSC (Protection Setting 2026) ........................ 1-16, 2-47
CONFTRIP (Protection Setting 2025) ................................ 2-47
CONNECTING
to & logging out of device ............................................... 11-9
CONSTRUCTION ........................................................ 3-1, 3-6
CONTACT CONVERTERS
calculation of settings ...................................................... 2-8
default assignments ......................................................... 1-9
digital output test ........................................................... 8-12
input flags ...................................................................... 13-4
protection settings ........................................................... 2-8
status ............................................................................ 8-18
CONTACT RATINGS .......................................................... 7-1
CONTINUOUS MONITOR ................................................. 1-22
CONTRAST ...................................................................... 8-15
COUNTERS ..................................................................... 13-3
CS28A ............................................................................. 1-30
interconnection diagram for blocking scheme .................. 1-32
CS61C ............................................................................. 1-23
interconnection diagram for blocking scheme .................. 1-32
CT RATIO
see CURRENT TRANSFORMER RATIO
CTRATIO (Protection Setting 1407) ................................... 2-37
CURRENT SUPERVISION FUNCTION ................................ 7-1
CURRENT TRANSFORMER RATIO
setting ........................................................................... 2-37
CURRENT UNBALANCE DETECTION ............................... 1-16
CURVES
extremely inverse curve ................................................. 2-50
inverse curve ................................................................. 2-48
very inverse curve .......................................................... 2-49
CUSTOM PROGRAMMABILITY ..........................................1-9
D
DATE/TIME
modifying ......................................................................... 8-7
DBUSDLINE (Protection Setting 1838) .............................. 2-45
DBUSLLINE (Protection Setting 1837) ............................... 2-45
DEFTIMDELY (Protection Setting 616) .............................. 2-27
DELTAV (Protection Setting 1839) ........................... 1-48, 2-45
DELTAVBLK (Protection Setting 1840) ..................... 1-48, 2-46
DESCRIPTION ...................................................................1-4
DEVICE PROFILE DOCUMENT (DNP 3.0) ......................... C-2
DIGITAL INPUT TEST ........................................................ 4-9
DIGITAL INPUTS
see CONTACT CONVERTERS
DIGITAL OUTPUTS
power supply board ........................................................ 3-10
test .............................................................................. 11-13
DIGITAL-TO-ANALOG CONVERTER
see SCADA DTA
DIMENSIONS .....................................................................7-2
DISABLE OUTPUTS
with ALPS-Link ............................................................ 11-12
with keypad .....................................................................8-8
DISPLAY
contrast ......................................................................... 8-15
description .......................................................................8-1
messages ........................................................................ 8-3
DISPLAYVAL (General Setting 108) .................................... 2-4
DISTANCE FUNCTIONS
maximum allowable reach .............................................. 2-13
Xpression Builder flags .................................................. 13-6
Zone 1 ...................................................................... 1-4, 2-9
Zone 2 ........................................................................... 2-14
ALPS Advanced Line Protection System iii