GE ALPS Instruction Manual page 353

INDEX
Numerics
1PDELAY1 (Protection Setting 1804) ................................ 2-42
1PDELAY2 (Protection Setting 1805) ................................ 2-42
1PDELAY3 (Protection Setting 1806) ................................ 2-42
1PDELAY4 (Protection Setting 1807) ................................ 2-43
3PDELAY1 (Protection Setting 1809) ................................ 2-43
3PDELAY2 (Protection Setting 1810) ................................ 2-43
3PDELAY3 (Protection Setting 1811) ................................ 2-43
3PDELAY4 (Protection Setting 1812) ................................ 2-43
50 (Protection Setting 601) ............................................... 2-25
50 FUNCTION ................................................ 1-11, 1-22, 2-25
directional control of ...................................................... 2-25
fuse failure blocking ...................................................... 2-29
pickup setting ........................................................2-25, 2-26
50_DIRCNL (Protection Setting 602) ................................. 2-25
50G (Protection Setting 605) ............................................ 2-26
50G FUNCTION ....................................... 1-4, 1-11, 1-22, 1-37
directional control of ...................................................... 2-26
fuse failure blocking ...................................................... 2-29
maximum postive value .................................................. 2-26
operating quantity .......................................................... 2-26
pickup ........................................................................... 2-26
recloser blocking ........................................................... 2-29
restraint ........................................................................ 2-26
setting ........................................................................... 2-26
50G_BLOCK (Protection Setting 804) ............................... 2-29
50G_DIRCNL (Protection Setting 606) .............................. 2-26
50GPICKUP (Protection Setting 607) ................................ 2-26
calculating ..................................................................... 2-26
50GPICKUPFF (Protection Setting 608) ............................ 2-26
50GRESTNT (Protection Setting 609) ............................... 2-26
with50G operating quantity ............................................ 2-26
50PICKUP (Protection Setting 603) .................................. 2-25
50PICKUPFF (Protection Setting 604) .............................. 2-26
51G (Protection Setting 610) ............................................ 2-26
51G FUNCTION ................................................ 1-4, 1-11, 1-37
characteristic curve shape ............................................. 2-27
directional control of ...................................................... 2-27
fuse failure blocking ...................................................... 2-29
operating quantity .......................................................... 2-27
pickup ........................................................................... 2-27
setting ........................................................................... 2-26
time-dial setting ............................................................. 2-27
51G_RESET (Protection Setting 617) ............................... 2-27
51GCURVE (Protection Setting 614) ................................. 2-27
51GDIRCNL (Protection Setting 611) ................................ 2-27
51GPICKUP (Protection Setting 612) ................................ 2-27
51GPICKUPFF (Protection Setting 613) ............................ 2-27
51GTIMDIAL (Protection Setting 615) ............................... 2-27
52/A CONTACT .......................................................1-18, 1-19
52/B CONTACTS .............................................. 1-25, 1-27, 2-2
blocking scheme ............................................................ 2-34
hybrid scheme ............................................................... 2-34
POTT1 scheme ............................................................. 2-34
POTT2 scheme ............................................................. 2-34
PUTT scheme ............................................................... 2-34
A
A1 (Protection Setting 2007) ............................................ 2-46
A10 (Protection Setting 2016) ........................................... 2-46
A11 (Protection Setting 2017) ........................................... 2-46
A12 (Protection Setting 2018) ........................................... 2-46
GE Power Management
INDEX
A2 (Protection Setting 2008) ............................................. 2-46
A3 (Protection Setting 2009) ............................................. 2-46
A4 (Protection Setting 2010) ............................................. 2-46
A5 (Protection Setting 2011) ............................................. 2-46
A6 (Protection Setting 2012) ............................................. 2-46
A7 (Protection Setting 2013) ............................................. 2-46
A8 (Protection Setting 2014) ............................................. 2-46
A9 (Protection Setting 2015) ............................................. 2-46
ACCEPTANCE/PERIODIC TESTS ....................................... 4-1
AC system input test ...................................................... 4-10
configurable input test ...................................................... 4-9
configurable output test .................................................... 4-9
digital output test ............................................................. 4-8
display test ...................................................................... 4-7
entering test mode ........................................................... 4-6
exiting test mode ............................................................. 4-6
general instructions .......................................................... 4-2
general relay tests ........................................................... 4-1
initial test setup ............................................................... 4-6
introduction .....................................................................4-1
keypad test ...................................................................... 4-7
relay status ...................................................................... 4-7
required settings .............................................................. 4-2
setting changes ............................................................... 4-3
test equipment .................................................................4-1
test unit description .......................................................... 4-5
ACCURACIES .................................................................... 7-2
ACT KEY
menu .............................................................................. D-2
using
ACTIONS ....................................................................... 11-12
editing ............................................................................. 8-8
list ................................................................................... 8-8
ACTIVE SETTINGS GROUP
selecting .......................................................................... 8-7
ADAPTIVE MEMORY
with Zone 4 phase distance functions ............................. 2-19
ADAPTIVE REACH ............................................................. 1-4
ALARMS .......................................................................... 1-19
continuous monitor alarm ............................................... 1-22
critical ............................................................................. 4-3
critical alarm .................................................................. 1-19
line overload .................................................................. 1-19
non-critical ...........................................1-16, 1-19, 1-22, 2-46
overcurrent ........................................................... 1-19, 1-22
power supply ................................................................. 1-19
trip circuit alarm .................................................... 1-19, 1-22
unbalanced current detector .................................. 1-22, 2-25
zone flags on ........................................................ 1-19, 1-22
ALL_3_Z2PH (Protection Setting 803) ............................... 2-29
ALL_BELOW (Protection Setting 801) ............................... 2-29
ALPS
communications ........................................................ 2-4, 4-4
default settings ................................................................ 4-5
servicing .......................................................................... 9-1
status check .................................................................... 4-7
test mode ........................................................................ 4-4
ALPS-LINK
breaker health report .................................................... 11-15
calculation of settings ...................................................... 2-1
change password ......................................................... 11-12
changing output settings ................................................ 2-46
close breaker ............................................................... 11-13
communications ................................. 2-4, 2-5, 4-4, 11-9, A-1
contact status report .................................................... 11-16
date & time .................................................................. 11-11
demand report ............................................................. 11-15
ALPS Advanced Line Protection System i