GE ALPS Instruction Manual page 123

2 CALCULATION OF SETTINGS
Table 2–11: PROTECTION SETTINGS GUIDE (Sheet 3 of 7)
NO. MNEMONIC
613 51GPCKUPFF
614 51GCURVE
615 51GTIMDIAL
616 DEFTIMDELY
617 51G_RESET
VOLTAGE
701 RATEDVOLTS
702 PHASEOVER
703 PHOVPICKUP
704 PHOVTMDLY
705 V1OVER
706 V1OVINSTPU
707 V1OVTIMPU
708 V1OVTIMDLY
709 V1COMP
710 V1COMPRCH
711 V1COMPINPU
712 V1COMPTDPU
713 V1COMPTDLY
714 FUSEFAIL
BLK RECLOS
801 ALL_BELOW
802 OUTOFSTEP
803 ALL_3_Z2PH
804 50G_BLOCK
805 Z2TIMETRIP
806 Z3TIMETRIP
807 Z4TIMETRIP
808 Z1PHASTRIP
809 ANYZ2PHASE
810 CONFGTRIP
LINEPICKUP
901 LINEPICKUP
† Setting value QUAD applies to Revision B models only.
‡ Setting applicable to Revision B models only.
^ Setting applicable to Single Phase Tripping models only.
GE Power Management
DESCRIPTION
51G Pickup during fuse failure
51G Curve
51G Time Dial
Definite Time Delay
51G Reset Characteristic
Rated Per Unit Voltage
Select Phase Overvoltage
Phase Overvoltage Pickup
Phase Overvoltage Time Delay
Select Positive Sequence
Overvoltage (Overvoltage Model
Only)
Instantaneous Positive Sequence
Overvoltage Pickup (Overvoltage
Model Only)
TOV Positive Sequence
Overvoltage Pickup (Overvoltage
Model Only)
Positive Sequence Overvoltage
Time Delay (Overvoltage Model
Only)
Compensated Positive Sequence
Overvoltage (Overvoltage Model
Only)
Compensated Positive Sequence
Overvoltage Impedance
(Overvoltage Model Only)
INST Compensated Positive
Sequence OV Pickup
(Overvoltage Model Only)
TOV Compensated Positive
Sequence OV Pickup
(Overvoltage Model Only)
Compensated Positive Sequence
OV Time Delay (Overvoltage
Model Only)
Potential Fuse Failure Blocking
Block reclosing for any function
Block for Out of Step
Block for 3 phase faults
Block for 50G trip
Block for Z2 Time Delayed Trip
Block for Z3 Time Delayed Trip
Block for Z4 Time Delayed Trip
Block for any Z1 Phase Fault
Block for any Z2 Phase Fault
Block For Configurable Trip Logic
Select Line Pickup
ALPS Advanced Line Protection System
RANGE (5A) RANGE (1A)
0.20 to 15.0 amps 0.04 to 3.0 amps
step 0.01 step 0.01
INV, V-INV, E-INV, CUSTOM, DEFT
0.5 to 10.0 step 0.1
0.5 to 30.0 sec. step 0.1
FAST, EM
100, 105,110,115, 120 volts
NO, YES
0.0 to 1.4 p.u. volts step 0.01
0.0 to 10.0 sec. step 0.01
NO, YES
1.0 to 1.4 p.u. volts step 0.01
1.0 to 1.4 p.u. volts step 0.01
0.0 to 10.0 sec. step 0.01 sec.
NO, YES
0.01 to 50.0 ohms 0.05 to 250.0 ohms
step 0.01 step 0.05
0.0 to 1.4 p.u. volts step 0.01
0.0 to 1.4 p.u. volts step 0.01
0.0 to 10.0 sec. step 0.01
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
2.5 REFERENCE TABLES
DEFAULT
2.0 A at 5A
0.4 A at 1A
V-INV
5
1.0 sec.
FAST
115 volts
NO
1.4 V
0.50 sec.
NO
1.25 p.u. V
1.25 p.u. V
0.25 sec.
NO
6.0Ω at 5A
30.0Ω at 1A
1.4 p.u. V
1.4 p.u. V
0.3 s at 5A
1.5 s at 1A
YES
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
2-59
2