List Of Tables; E.1.2 List Of Tables - GE ALPS Instruction Manual

APPENDIX E
T : 1–1 ORDER CODES............................................................................................................................................................... 1-3
ABLE
T : 1–2 ALPS MEASUREMENT FUNCTIONS ............................................................................................................................. 1-5
ABLE
T : 1–3 ALPS DEFAULT CONTACT CONVERTER ASSIGNMENTS: SINGLE PHASE MODEL................................................ 1-9
ABLE
T : 1–4 ALPS DEFAULT CONTACT CONVERTER ASSIGNMENTS: THREE PHASE MODEL................................................. 1-9
ABLE
T : 1–5 ALPS DEFAULT OUTPUT CONTACT ASSIGNMENTS: SINGLE PHASE MODEL ..................................................... 1-10
ABLE
T : 1–6 ALPS DEFAULT OUTPUT CONTACT ASSIGNMENTS: THREE PHASE MODEL ...................................................... 1-10
ABLE
T : 1–7 CHANNEL KEYING FOR PILOT TRIPPING (TWO CHANNELS) ................................................................................. 1-38
ABLE
T : 1–8 SINGLE POLE PHASE A TRIP LOGIC.......................................................................................................................... 1-39
ABLE
T : 1–9 REPEAT KEYING LOGIC .............................................................................................................................................. 1-39
ABLE
T : 1–10 CHANNEL KEYING FOR PILOT TRIPPING (FOUR CHANNELS).............................................................................. 1-40
ABLE
T : 1–11 PILOT KEYING (4 CHANNEL) LOGIC......................................................................................................................... 1-40
ABLE
T : 2–1 NUM_TC SETTING (SINGLE PHASE MODELS) ............................................................................................................ 2-3
ABLE
T : 2–2 NUM_TC SETTING (THREE PHASE MODELS) ............................................................................................................. 2-3
ABLE
T : 2–3 SETTING FORMAT FOR NUM_MON (SINGLE PHASE TRIPPING MODELS).............................................................. 2-4
ABLE
T : 2–4 SETTING FORMAT FOR NUM_MON (THREE PHASE TRIPPING MODELS)............................................................... 2-4
ABLE
T : 2–5 OSCILLOGRAPHY CYCLES PER STORAGE EVENT ................................................................................................... 2-6
ABLE
T : 2–6 CONTACT CONVERTER ASSIGNMENT FOR PHASE IDENTIFIED CHANNEL SCHEME .......................................... 2-8
ABLE
T : 2–7 PROPOSED SETTINGS FOR BLOCKING SCHEME.................................................................................................... 2-23
ABLE
T : 2–8 OUTPUT ASSIGNMENT FOR HYBRIDP SCHEME ...................................................................................................... 2-46
ABLE
T : 2–9 INDEX NUMBERS – CONTACT CONVERTER INPUT ASSIGNMENT ........................................................................ 2-51
ABLE
T : 2–10 INDEX NUMBERS – SCHEME, RECLOSER, & PROGRAMMABLE LOGIC .............................................................. 2-52
ABLE
T : 2–11 PROTECTION SETTINGS GUIDE............................................................................................................................... 2-57
ABLE
T : 2–12 GENERAL SETTINGS GUIDE ..................................................................................................................................... 2-64
ABLE
T : 2–13 PROTECTION SETTINGS DATA SHEET ................................................................................................................... 2-66
ABLE
T : 2–14 GENERAL SETTINGS DATA SHEET.......................................................................................................................... 2-73
ABLE
T : 3–1 JUMPER POSITION......................................................................................................................................................... 3-7
ABLE
T : 4–1 FACTORY DEFAULT COMMUNICATIONS PARAMETERS........................................................................................... 4-5
ABLE
T : 4–2 DIGITAL OUTPUTS TEST CONNECTIONS.................................................................................................................... 4-8
ABLE
T : 4–3 ........................................................................................................................................................................................ 4-12
ABLE
T : 5–1 .......................................................................................................................................................................................... 5-6
ABLE
T : 5–2 ........................................................................................................................................................................................ 5-18
ABLE
T : 6–1 TEST CURRENT RANGES FOR PHASE-TO-GROUND REACH ................................................................................. 6-11
ABLE
T : 6–2 TEST CURRENT RANGES FOR PHASE-TO-PHASE REACH..................................................................................... 6-15
ABLE
T : 8–1 PASSWORD ENCRYPTION KEY TABLE ..................................................................................................................... 8-21
ABLE
T : 8–2 KEYPAD / DISPLAY INTERFACE ERROR MESSAGES .............................................................................................. 8-22
ABLE
T : 8–3 HARDWARE SWITCH DESCRIPTIONS ....................................................................................................................... 8-24
ABLE
T : 8–4 COMMAND SEQUENCE SENT TO MODEM ................................................................................................................ 8-25
ABLE
T : 8–5 CONFIGURATION SETTINGS FOR THE MODEM CONNECTED TO THE RELAY .................................................... 8-26
ABLE
T : 8–6 MODEM COMMANDS FOR COMMUNICATION BETWEEN RELAY AND PC ............................................................ 8-27
ABLE
T : 9–1 COMPONENTS TESTED DURING START-UP TESTS .................................................................................................. 9-2
ABLE
T : 9–2 RUN-TIME BACKGROUND SELF-TESTS ...................................................................................................................... 9-2
ABLE
T : 9–3 RUN-TIME FOREGROUND SELF-TESTS ...................................................................................................................... 9-2
ABLE
T : 9–4 SYSTEM STATUS ERROR MESSAGES ........................................................................................................................ 9-3
ABLE
T : 10–1 INPUT QUANTITIES .................................................................................................................................................... 10-2
ABLE
T : 12–1 OSCILLOGRAPHY DATA STRUCTURE ..................................................................................................................... 12-1
ABLE
T : 12–2 ASCII COMMAND LIST .............................................................................................................................................. 12-2
ABLE
T : 13–1 PICKUP DELAY TIMER TRUTH TABLE...................................................................................................................... 13-3
ABLE
T : 13–2 CONTACT CONVERTER INPUT FLAGS .................................................................................................................... 13-4
ABLE
T : 13–3 CONFIGURABLE INPUTS ........................................................................................................................................... 13-4
ABLE
T : 13–4 SCHEME LOGIC AND RECLOSER OUTPUTS .......................................................................................................... 13-5
ABLE
T : 13–5 SCHEME LOGIC INPUTS............................................................................................................................................ 13-6
ABLE
T : 13–6 DISTANCE UNITS........................................................................................................................................................ 13-6
ABLE
T : 13–7 CURRENT AND VOLTAGE UNITS.............................................................................................................................. 13-7
ABLE
T : 13–8 MISCELLANEOUS ....................................................................................................................................................... 13-8
ABLE
T : 13–9 USER DEFINABLE OUTPUT FLAGS .......................................................................................................................... 13-8
ABLE
Table: B–1 REQUIRED SETTINGS FOR MODBUS COMMUNICATIONS........................................................................................ B-1
Table: B–2 FAULT REPORT BYTE SEQUENCE...............................................................................................................................B-3
Table: B–3 FAULT REPORT EVENTS SEQUENCE.......................................................................................................................... B-4
Table: B–4 MODBUS MEMORY MAP ................................................................................................................................................ B-5
Table: B–5 DATA FORMATS............................................................................................................................................................ B-15
Table: C–1 IMPLEMENTATION TABLE .............................................................................................................................................C-4
Table: C–2 DEFAULT VARIATIONS ..................................................................................................................................................C-5
GE Power Management ALPS Advanced Line Protection System
E.1 FIGURES AND TABLES

E.1.2 LIST OF TABLES

E-
E
3