GE ALPS Instruction Manual page 135

2 CALCULATION OF SETTINGS
Table 2–13: PROTECTION SETTINGS DATA SHEET (Sheet 6 of 7)
NO. MNEMONIC
1815 HOLD
1816 HOLDTIME
1817 HOLDSENSE
1818 SYNCCHECK
1819 CLOSEANG
1820 SLIPFREQ
1821 BUSLINE
1822 SYNCPHASE
1823 SYNCHOLD
^ SP1DELAY2
1824
SP1DELAY3
^
1825
^ SP1DELAY4
1826
1827 SP3DELAY1
1828 SP3DELAY2
1829 SP3DELAY3
1830 SP3DELAY4
1831 SYNCMANCLS
1832 VBUSLIVE
1833 VBUSDEAD
1834 VLINELIVE
1835 VLINEDEAD
1836 LBUSDLINE
1837 DBUSLLINE
1838 DBUSDLINE
1839 DELTAV
1840 DELTAVBLK
NONCRIT_AL
1901 NCAIN1
1902 NCAIN2
1903 NCAIN3
1904 NCAIN4
1905 NCAIN5
1906 NCAIN6
1907 NCAIN7
1908 NCAIN8
OUTPUTS
2001 T1
2002 T2
† Setting value QUAD applies to Revision B models only.
‡ Setting applicable to Revision B models only.
^ Setting applicable to Single Phase Tripping models only.
GE Power Management
DESCRIPTION
Inhibit Hold Select
Inhibit Hold Time
Contact Input Status
Synch Check Supervision
Closing Angle
Slip Frequency
Bus or Line Voltage
Voltage used by SYNCCHECK
SYNCCHECK Hold Time
Supervise 2nd 3P Reclose after
1P Trip
Supervise 3rd 3P Reclose after 1P
Trip
Supervise 4th 3P Reclose after 1P
Trip
Supervise 1st 3P Reclose after 3P
Trip
Supervise 2nd 3P Reclose after
3P Trip
Supervise 3rd 3P Reclose after 3P
Trip
Supervise 4th 3P Reclose after 3P
Trip
Supervise Manual Close
Live Bus Voltage
Dead Bus Voltage
Live Line Voltage
Dead Line Voltage
Live Bus Dead Line
Dead Bus Live Line
Dead Bus Dead Line
Voltage Difference
Block Synch Check by DELTAV
Non-Critical Alarm Input #1
These 8 inputs are ORed together
and then outputted to the contact
assigned to the Non-Critical Alarm
Non-Critical Alarm Input #2
Non-Critical Alarm Input #3
Non-Critical Alarm Input #4
Non-Critical Alarm Input #5
Non-Critical Alarm Input #6
Non-Critical Alarm Input #7
Non-Critical Alarm Input #8
T1 Contract
T2 Contact
ALPS Advanced Line Protection System
RANGE (5A) RANGE (1A)
NO, YES
1 to 1000 sec. step 1
CC, CO
NO, YES
0 to 75 deg. step 1
0.1 to 5 Hz step 0.1
BUS, LINE
VA, VB, VC, VAB, VBC, VCA
1 to 100 sec. step 1
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
0.1 to 130 volts step 0.1
0.1 to 130 volts step 0.1
0.1 to 130 volts step 0.1
0.1 to 130 volts step 0.1
NO, YES
NO, YES
NO, YES
0.1 to 30 volts step 0.1
NO, YES
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
0 to 256 step 1
2.5 REFERENCE TABLES
USER
SETTING
2-71
2