Mitsubishi Electric Melsec Q Series User Manual page 197

6 DEDICATED INSTRUCTIONS
Device
(S1) + 12
Clock data (set only if an error
to
occurs) (
(S1) + 15
Abnormal detection network
(S1) + 16
number (
Abnormal detection station
(S1) + 17
number (
Request data (All values are set by the user)
Device
(S2) + 0 Request type
(S2) + 1 Sub-request type
(S2) + 2 Mode
(S2) + 3 Clear mode
6 - 30
Item
The clock data upon abnormal end is stored in BCD.
This data is stored only when the bit 7 of Abnormal complete
type ((S1) + 0) is 1. The stored value is not cleared even when
the dedicated instruction is normally completed.
b15
(S1) 12
2
)
(S1) 13
(S1) 14
(S1) 15
Year (00
Stores the network number of the station that detected an
abnormality.
This data is stored only when the bit 7 of Abnormal complete
4
type ((S1) + 0) is 1. The stored value is not cleared even when
)
the dedicated instruction is normally completed.
1 to 239 (Network number)
Stores the station number of the station that detected an
abnormality.
This data is stored only when the bit 7 of Abnormal complete
4
type ((S1) + 0) is 1. The stored value is not cleared even when
)
the dedicated instruction is normally completed.
1 to 120 (Station number)
1 The "Set by" column indicates the following:
• User: Data is set by the user before executing a dedicated instruction.
• System: The programmable controller CPU stores the execution result of a
dedicated instruction.
2 For a list of error codes, see the User's Manual (Basic).
3 It can be specified when the local station has an Ethernet module of function
version D or later. (The setting value is fixed to "03FF
the above. Access is made to the control CPU.)
4 Nothing is stored if the execution source detects an error when receiving an
instruction.
5 When the REQ instruction is executed to the redundant system with a control
system or standby system CPU specified, the instruction may be unsuccessfully
completed due to system switching occurred on the target station (error code:
4244 , 4248 ).
H H
If this has occurred, execute the REQ instruction again.
Item
0010 : When station No. is specified in (S1)+5
H
0030 : When all stations or a group is specified in (S1)+5
H
0001 : Remote RUN
H
0002 : Remote STOP
H
Designate whether or not to forcefully execute remote
RUN/STOP operations.
0001 : Do not force execution
H
0003 : Force execution (setting at remote STOP)
H
(The forced execution is a function for forcefully executing
remote RUN from other station when the station that executed
the remote STOP is no longer able to execute remote RUN.)
Designate the status of the CPU's device memory only when
executing remote RUN.
0000 : Do not clear (however, the local device will be cleared)
H
0001 : Clear (excluding setting and latch range at remote RUN)
H
0002 : Clear (including setting and latch range at remote RUN)
H
Set data
to
b8 b7
Month (01 to 12 ) Year (00
H H H
Hour (00 to 23 ) Date (01
H H
Minute (00
Second (00 to 59 )
H H
Day of the week (00
to 99 ), First 2 digits
H H
00
H
Description
MELSEC-Q/L
Setting range
to b0
to 99 ), Last 2 digits —
H
to 31 )
H H
to 59 )
H H
to 06 )
H H
(Sun.) to 06 (Sat.)
H
—
—
" for a module other than
H
Remote RUN
1
Set by ( )
System
System
Remote STOP
—
6 - 30