Input Selector Block Parameter List - Emerson Fisher Fieldvue DVC6030f Instruction Manual

DVC6000f Series

Input Selector Block Parameter List

D Read/Write Capability: RO − Read Only, RW − Read Write
D Mode: The block mode(s) required to write to the parameter
D Double indentations and shaded Index Numbers indicate sub-parameters
Label
PARAMETER_NAME
Static Revision
ST_REV
Tag Description
TAG_DESC
5
Strategy
STRATEGY
Alert Key
ALERT_KEY
Block Mode
MODE_BLK
TARGET
ACTUAL
PERMITTED
NORMAL
Block Error
BLOCK_ERR
Output
OUT
Output Range
OUT_RANGE
Grant Deny
GRANT_DENY
GRANT
DENY
Status Options
STATUS_OPTS
Input 1
IN_1
5-106
Table 5-39. Input Selector Function Block Parameter Definitions
Index RO / Block
Number RW Mode
1 RO N/A 0 to 65535
2 RW ALL 7 bit ASCII
3 RW ALL 0 to 65535
4 RW ALL 1 to 255
5
5.1 RW ALL OOS, MAN, AUTO
5.2 RO ALL
5.3 RW ALL OOS+MAN+AUTO
5.4 RW ALL
1: Block
Configuration Error
7: Input Failure / Bad
6 RO N/A PV status
8: Output Failure
14: Power Up
15: Out-of-Service
Status
MAN
OUT_RANGE
7
OOS
Value
EU at 100%
EU at 0%
8 ALL
Units Index
Decimal Point
9
0: Program
9.1 ALL
1: Tune
2: Alarm
9.2 ALL
3: Local
2: Use Uncertain as
10 OOS GOOD
8: Uncertain if MAN
Status
11 ALL
Value
Initial
Range
Value
Data Type: Unsigned16
The revision level of the static data associated with
0 the function block. The revision value will be
incremented each time a static parameter value in the
block is changed.
Data Type: Octet String
spaces The user description of the intended application of the
block.
Data Type: Unsigned16
The strategy field can be used to identify grouping of
0
blocks. This data is not checked or processed by the
block.
Data Type: Unsigned8
The identification number of the plant unit. This
0
information may be used in the host for sorting
alarms, etc.
Data Type: DS-69
OOS until
Valid Bits: 7: OOS, 4: MAN,
block is
3: AUTO
configured,
The actual, target, permitted, and normal modes of
then last
the block.
valid target
Target: The requested block mode
Actual: The current mode of the block
Permitted: Allowed modes for Target
OOS+MAN
Normal: Most common mode for Target
+AUTO
AUTO
Data Type: Bit String
0=Inactive
1=Active
Dynamic This parameter reflects the error status associated
with the hardware or software components
associated with a block. It is a bit string, so that
multiple errors may be shown.
Data Type: DS-65
Dynamic
The block output value and status.
100 Data Type: DS-67
0 High and low scale values, engineering units code,
% and number of digits to the right of the decimal point
2 associated with OUT.
Data Type: DS-70
Options for controlling access of host computers and
local control panels to operating, tuning, and alarm
All bits: 0
parameters of the block. Not used by device.
GRANT: 0=N/A, 1=granted
All bits:0
DENY: 0=N/A, 1=denied
Data Type: Bit String
Allows you to select options for status handling and
All bits: 0 processing. The supported status option for the input
selector block is: "Use Uncertain as Good",
"Uncertain if Man mode."
BAD
NC
Data Type: DS-65
constant
The block input value and status.
0
−Continued−
Description
March 2006