Flash Messages - GE 489 Instruction Manual

5 ACTUAL VALUES
Flash messages are warning, error, or general information messages that are temporarily displayed in response to certain
key presses. These messages are intended to assist with navigation of the 489 messages by explaining what has hap-
pened or by prompting the user to perform certain actions.
Table 5–2: FLASH MESSAGES
NEW SETPOINT HAS ROUNDED SETPOINT
BEEN STORED HAS BEEN STORED
INVALID PASSCODE NEW PASSCODE
ENTERED! HAS BEEN ACCEPTED
SETPOINT ACCESS IS DATE ENTRY WAS
NOW RESTRICTED NOT COMPLETE
NO TRIPS OR ALARMS RESET PERFORMED
TO RESET SUCCESSFULLY
PRESS [ENTER] TO ADD DEFAULT MESSAGE
DEFAULT MESSAGE HAS BEEN ADDED
DEFAULT MESSAGES INVALID SERVICE CODE
6 TO 20 ARE ASSIGNED ENTERED
TOP OF PAGE END OF PAGE
THIS FEATURE NOT THIS PARAMETER IS
PROGRAMMED ALREADY ASSIGNED
•
NEW SETPOINT HAS BEEN STORED:
on the display.
•
ROUNDED SETPOINT HAS BEEN STORED:
between valid setpoint values. The 489 detects this condition and store a value rounded to the nearest valid setpoint
value. To find the valid range and step for a given setpoint, press the
•
OUT OF RANGE! ENTER: #### - ##### by #:
displays this message and substitutes proper values for that setpoint. An appropriate value may then be entered.
•
ACCESS DENIED, SHORT ACCESS SWITCH:
sage appears and it is necessary to change a setpoint, short the Access terminals C1 and C2.
•
ACCESS DENIED, ENTER PASSCODE:
the Access Switch terminals be shorted, but a valid passcode must also be entered. If the correct passcode has been
lost or forgotten, contact the factory with the encrypted access code. All passcode features may be found in the
setpoints menu.
SETUP \ PASSCODE
•
INVALID PASSCODE ENTERED:
feature.
•
NEW PASSCODE HAS BEEN ACCEPTED:
accepted when changing the passcode for the passcode security feature.
•
PASSCODE SECURITY NOT ENABLED, ENTER 0:
(factory default). Any attempts to enter a passcode when the feature is disabled results in this flash message, prompt-
ing the user to enter "0" as the passcode. When this has been done, the feature may be enabled by entering a non-
zero passcode.
•
PLEASE ENTER A NON-ZERO PASSCODE:
CHANGE PASSCODE SETPOINT
passcode and enable the passcode security feature.
•
SETPOINT ACCESS IS NOW PERMITTED:
entered, this flash message appears to notify that setpoints may now be altered and stored.
•
SETPOINT ACCESS IS NOW RESTRICTED:
message appears when the
sage also appears any time that setpoint access is permitted and the access jumper is removed.
GE Power Management
OUT OF RANGE.! ENTER:
####-##### by #
PASSCODE SECURITY
NOT ENABLED, ENTER 0
DATE ENTRY
OUT OF RANGE
ALL POSSIBLE RESETS
HAVE BEEN PERFORMED
DEFAULT MESSAGE
LIST IS FULL
KEY PRESSED IS
INVALID HERE
TOP OF LIST
THAT INPUT ALREADY
USED FOR TACHOMETER
This message appear each time a setpoint has been altered and stored as shown
Since the 489 has a numeric keypad, an entered setpoint value may fall
If a setpoint value outside the acceptable range of values is entered, the 489
The Access Switch must be shorted to store any setpoint values. If this mes-
The 489 has a passcode security feature. If this feature is enabled, not only must
This flash message appears if an invalid passcode is entered for the passcode security
This message will appear as an acknowledge that the new passcode has been
The passcode security feature is disabled whenever the passcode is zero
The passcode security feature is disabled if the passcode is zero. If the
is entered as yes, this flash message appears prompting the user to enter a non-zero
Any time the passcode security feature is enabled and a valid passcode is
If the passcode security feature is enabled and a valid passcode entered, this
S1 489 SETUP \ PASSCODE \ SETPOINT ACCESS
489 Generator Management Relay
5.8 DIAGNOSTICS

5.8.2 FLASH MESSAGES

ACCESS DENIED, ACCESS DENIED,
SHORT ACCESS SWITCH ENTER PASSCODE
PLEASE ENTER A SETPOINT ACCESS IS
NON-ZERO PASSCODE NOW PERMITTED
TIME ENTRY WAS TIME ENTRY
NOT COMPLETE OUT OF RANGE
CONDITION IS PRESENT ARE YOU SURE? PRESS
RESET NOT POSSIBLE [ENTER] TO VERIFY
PRESS [ENTER] TO DEFAULT MESSAGE
REMOVE MESSAGE HAS BEEN REMOVED
DATA CLEARED [.] KEY IS USED TO
SUCCESSFULLY ADVANCE THE CURSOR
END OF LIST NO ALARMS ACTIVE
TACHOMETER MUST USE THAT DIGITAL INPUT
INPUT 4, 5, 6, OR 7 IS ALREADY IN USE
key while the setpoint is being displayed.
HELP
setpoint is altered to "Restricted". This mes-
5
S1 489
5-27