GE 489 Instruction Manual page 186

6.3 MEMORY MAP
Table 6–2: DATA FORMATS (Sheet 3 of 5)
FORMAT TYPE
CODE
F129 Unsigned
16 bit integer
F130 Unsigned
16 bit integer
F131 Unsigned
16 bit integer
F132 Unsigned
16 bit integer
F133 Unsigned
16 bit integer
F134 Unsigned
16 bit integer
6
6-42
DEFINITION
Analog input selection
0 = Disabled, 1 = 4-20 mA, 2 = 0-20 mA, 3 = 0-1 mA
Pickup type
0 = Over, 1 = Under
Input switch status
0 = Closed, 1 = Open
Trip coil supervision status
0 = No Coil, 1 = Coil
Generator status
0 = Offline, 1 = Offline, 2 = Online, 3 = Overload, 4 = Tripped
Cause of event / Cause of trip
VALUE PARAMETER
0 No Event
1 General Sw. A Trip
2 General Sw. B Trip
3 General Sw. C Trip
4 General Sw. D Trip
5 General Sw. E Trip
6 General Sw. F Trip
7 General Sw. G Trip
8 Sequential Trip
9 Tachometer Trip
10 UNKNOWN TRIP
11 UNKNOWN TRIP
12 Overload Trip
13 UNKNOWN TRIP
14 Neutral O/V Trip
15 Neut. U/V (3rd) Trip
16
17
18
19
20 Differential Trip
21 Acceleration Trip
22 RTD 1 Trip
23 RTD 2 Trip
24 RTD 3 Trip
25 RTD 4 Trip
26 RTD 5 Trip
27 RTD 6 Trip
28 RTD 7 Trip
29 RTD 8 Trip
30 RTD 9 Trip
31 RTD 10 Trip
32 RTD 11 Trip
33 RTD 12 Trip
34 Undervoltage Trip
35 Overvoltage Trip
36 Phase Reversal Trip
37 Overfrequency Trip
38 Power Factor Trip
39 Reactive Power Trip
40 Underfrequency Trip
41 Analog I/P 1 Trip
42 Analog I/P 2 Trip
43 Analog I/P 3 Trip
44 Analog I/P 4 Trip
45 Single Phasing Trip
46 Reverse Power Trip
489 Generator Management Relay
VALUE PARAMETER
47 Field-Bkr Discrep.
48 Offline O/C Trip
49 Phase O/C Trip
50 Neg. Seq. O/C Trip
51 General Sw. A Alarm
52 General Sw. B Alarm
53 General Sw. C Alarm
54 General Sw. D Alarm
55 General Sw. E Alarm
56 General Sw. F Alarm
57 General Sw. G Alarm
58
59 Tachometer Alarm
60 Thermal Model Alarm
61 Overload Alarm
62 Underfrequency Alarm
63
64 Ground Fault Alarm
65 RTD 1 Alarm
66 RTD 2 Alarm
67 RTD 3 Alarm
68 RTD 4 Alarm
69 RTD 5 Alarm
70 RTD 6 Alarm
71 RTD 7 Alarm
72 RTD 8 Alarm
73 RTD 9 Alarm
74 RTD 10 Alarm
75 RTD 11 Alarm
76 RTD 12 Alarm
77 Open RTD Alarm
78 Short/Low RTD Alarm
79 Undervoltage Alarm
80 Overvoltage Alarm
81 Overfrequency Alarm
82 Power Factor Alarm
83 Reactive Power Alarm
84 Low Fwd Power Alarm
85 Trip Counter Alarm
86 Breaker Fail Alarm
87 Current Demand Alarm
88 kW Demand Alarm
89 kvar Demand Alarm
90 kVA Demand Alarm
91 Broken Rotor Bar
92 Analog I/P 1 Alarm
93 Analog I/P 2 Alarm
6 COMMUNICATIONS
VALUE PARAMETER
94 Analog I/P 3 Alarm
95 Analog I/P 4 Alarm
96 Reverse Power Alarm
97 Incomplete Seq.Alarm
98 Negative Seq. Alarm
99 Ground O/C Alarm
100
101 Service Alarm
102 Control Power Lost
103 Cont. Power Applied
104 Thermal Reset Close
105 Emergency Rst. Open
106 Start While Blocked
107 Relay Not Inserted
108 Trip Coil Super.
109 Breaker Failure
110 VT Fuse Failure
111 Simulation Started
112 Simulation Stopped
113 Ground O/C Trip
114 Volts/Hertz Trip
115 Volts/Hertz Alarm
116 Low Fwd Power Trip
117 Inadvertent Energ.
118 Serial Start Command
119 Serial Stop Command
120 Input A Control
121 Input B Control
122 Input C Control
123 Input D Control
124 Input E Control
125 Input F Control
126 Input G Control
127 Neutral O/V Alarm
128 Neut. U/V 3rd Alarm
129 Setpoint 1 Active
130 Setpoint 2 Active
131 Loss of Excitation 1
132 Loss of Excitation 2
133 Gnd. Directional Trip
134 Gnd. Directional Alarm
135 HiSet Phase O/C Trip
136 Distance Zone 1 Trip
137 Distance Zone 2 Trip
138 Dig I/P Wavefrm Trig
139 Serial Waveform Trig
GE Power Management