Page 1
CLI Reference Guide Product Model: DES-1210-52/ME L2 Managed Metro Ethernet Switch Version 1.00 (release 20.01)
Page 3
Other trademarks and trade names may be used in th is document to refer to either the entities claiming the marks and names or their products. D-Link Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide INTRODUCTION The DES-1210-52/ME is L2 Metro Ethernet switche. It consists of 48 10/100Mbps ports plus 4 combo 10/100/1000Base-T ports and 2 dedicated SFP ports. The Switch can be managed through the Switch’s serial port, Telnet, or the Web-based management agent.
Page 20
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Figure 1–2 Boot Screen The Switch’s MAC address can also be found in the Web management program on the Switch Information (Basic Settings) window in the Configuration folder. The IP address for the Switch must be set before it can be managed with the Web-based manager. The Switch IP address can be automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the Switch must be known.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide USING THE CONSOLE CLI The Switch supports a console management interface that allows the user to connect to the Switch’s management agent via a serial port and a terminal or a computer running a terminal emulation program.
Page 22
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Figure 2–2 The ? Command When entering a command without its required parameters, the CLI displays the prompt: command: config account message and the options listed below. Figure 2–3 Example Command Parameter Help In this case, the command config account was entered with the parameter <username>.
Page 23
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide was pressed to re-enter the previous command (config account) at the command prompt. Now the appropriate username can be entered and the config account command re-executed. All commands in the CLI function in this way. In addition, the syntax of the help prompts are the same as presented in this manual angle brackets <...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide COMMAND SYNTAX The following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the CLI and available through the console interface uses the same syntax.
Page 25
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide {braces} Purpose Encloses an optional value or set of optional arguments. Syntax reset execute “reset” will return the switch to its factory default setting. Description Example reset command Please be aware that all configuration will be reset to default value.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide BASIC SWITCH COMMANDS The Basic Switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable password encryption disable password encryption create account [admin | operator | power-user | user] <username 15>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only Administrat level users can issue this command. Example usage: To disable password encryption on the Switch: DES-1210-52/ME:5# disable password encryption Command: disable password encryption Success. DES-1210-52/ME:5# create account Purpose To create user accounts.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Enter a case-sensitive new password:***** Enter the new password again for confirmation:***** Success. DES-1210-52/ME:5# config account Purpose To change the password for an existing user account. config account <username 15> Syntax The config account command changes the password for a user Description account that has been created using the create account command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide dlink Admin Total Entries : 1 DES-1210-52/ME:5# delete account Purpose To delete an existing user account. delete account <username 15> Syntax The delete account command deletes a user account that has been Description created using the create account command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show session Purpose To display information about currently logged-in users. show session Syntax The show session command displays a list of all the users that are Description logged-in at the time the command is issued. The information includes the session ID (0 for the first logged-in user, 1 for the next logged-in user, etc.), the Protocol used to connect to the Switch, the...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide IP Address : 10.90.90.90 (Manual) Subnet Mask : 255.0.0.0 Default Gateway : 0.0.0.0 System Boot Version : 1.00.010 System Firmware Version : 20.01.B082 System Hardware Version : C1 System Serial Number : QBDES12105200...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only Administrator or operate-level users can issue this command. Jumbo frames will be disabled after save and restart. Example usage: To disable jumbo_frames: DES-1210-52/ME:5# disable jumbo_frame Command: disable jumbo_frame Success. DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide enable clipaging Used to pause the scrolling of the console screen when a command Purpose displays more than one page. enable clipaging Syntax The enable clipaging command is used when issuing a command...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide based management software is 80. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To enable HTTP and configure the TCP port number to listen for Telnet requests: DES-1210-52/ME:5# enable web 80 Command: enable web 80 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide If the Switch is unable to complete the auto configuration process the previously saved local configuration file present in Switch memory will be loaded. Only Administrator or operator-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# show autoconfig Purpose Used to display the current autoconfig status of the Switch. show autoconfig Syntax The show autoconfig command is used to list the current status of Description the auto configuration function.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Description The disable auto learing command disables the MAC address auto learning feature on the Switch. Parameters None. Restrictions Only administrator-level users can issue this command. Example usage: To disable auto learning on the Switch:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To reload the Switch: DES-1210-52/ME:5# reload config config_id 1 Command: reload config config_id 1 Are you sure you want to reload the config?(y/n)y % Reload config 1 Success.fully. Are you sure you want to proceed with the system reboot?(y/n)y % Please wait, the switch is rebooting...
Page 40
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide VLAN Init exclude CPU Port... ### RTL8208 config - MAC ID = 0 ### ### RTL8208 config - MAC ID = 8 ### ### RTL8208 config - MAC ID = 16 ###...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide MAC Address : 00-01-02-03-04-05 H/W Version : F/W Version : 20.01.B045 Complete NpHwInit RTK.0> ............DES-1210-52/ME Fast Ethernet Switch Command Line Interface Firmware: Build 20.01.B045 Copyright(C) 2012 D-Link Corporation. All rights reserved.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# reset config force_agree Command: reset config force_agree Success. DES-1210-52/ME:5# logout To log out a user from the Switch’s console. Purpose Logout Syntax The logout command terminates the current user’s session on the Description Switch’s console.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Reply Not Received From : 10.90.90.97, Timeout : 3 secs Reply Not Received From : 10.90.90.97, Timeout : 3 secs Reply Not Received From : 10.90.90.97, Timeout : 3 secs Reply Not Received From : 10.90.90.97, Timeout : 3 secs Reply Not Received From : 10.90.90.97, Timeout : 3 secs...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Reply From : 3000::1, bytes=200, time<10ms Reply From : 3000::1, bytes=200, time<10ms --- 3000::1 Ping Statistics --- 4 Packets Transmitted, 4 Packets Received, 0% Packets Loss DES-1210-52/ME:5# traceroute The traceroute User EXEC mode command discovers routes that Purpose packets actually take when traveling to their destination.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Syntax traceroute6 <ipv6_addr> {[max-ttl <short 1-99> | min-ttl <short 1-99>} Description The traceroute6 command discovers routes that packets actually take when traveling to their destination. <ipv6_addr> - Specifies the IPv6 address of the destination host.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide GVRP ICMP ICMPv6 IGMP LACP LLDP PPPoE Reserved Multicast 0 TELNET DES-1210-52/ME:5# reset cpu port Purpose To reset the CPU port information. reset cpu port Syntax The reset cpu port command resets the CPU port information.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# disable telnet Purpose To disable telnet. disable telnet Syntax Description The disable telnet command disables telnet. Parameters None. Restrictions Only Administrator or operate-level users can issue this command. Example usage: To disable telnet:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide end_time <end_time 32 >– defines the time on which the time range will stop to be active. weekdays <daylist 32> – defines the days of the week on which the time range will be active.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show tech support Purpose To display system and configuration information. to provide to the Technical Assistance Center when reporting a problem, use the show tech-support command. show tech support Syntax show tech...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DHCP AUTOIMAGE COMMANDS The DHCP Autoimage commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable autoimage diable autoimage show autoimage...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# disable autoimage Command: disable autoimage Success. DES-1210-52/ME:5# show autoimage Purpose To display the DHCP automatic image function on the Switch. Syntax show autoimage Description The disable autoimage command is used to display the DHCP automatic image function on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide SMTP SERVER COMMANDS The SMTP Server commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable smtp disable smtp [self_mail_addr <mail_addr 64> | server [<ipaddr> | <ipv6addr>] | server_port config smtp <tcp_port_number 1-65535>] [{add mail_receiver <mail_addr 64>| delete...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To disable STMP feature on the Switch: DES-1210-52/ME:5# disable smtp Command: disable smtp Success. DES-1210-52/ME:5# config smtp Purpose To configure the fields to set up the SMTP server for the switch, along with setting e-mail addresses to which switch log files can be sent when a problem arises on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Syntax show smtp The show smtp command displays the SMTP server settings on the Description Switch. Parameters None. Restrictions None. Example usage: To display SMTP information on the Switch: DES-1210-52/ME:5# show smtp...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide MODIFY BANNER AND PROMPT COMMANDS The Modify Banner and Prompt commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config [<string 32> | default | username]...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config greeting_message Purpose Used to configure the login banner (greeting message). config greeting_message {default} Syntax The config greeting_message command to modify the login Description banner (greeting message). default – If the user enters default to the modify banner command, Parameters then the banner will be reset to the original factory banner.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide SWITCH PORT COMMANDS The Switch Port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [all | <portlist>] medium_type [copper | fiber] MDI/MDIX [MDI | MDIX | auto] {clear_description | description <desc 32>...
Example usage: To configure the speed of ports 1-3 to be 100 Mbps, full duplex, learning and state enabled: DES-1210-52/ME:5# config ports 1-3 medium_type copper speed 100_full learning enable state enable Command: config ports 1-3 medium_type copper speed 100_full learning enable state enable Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show ports Purpose To display the current configuration of a range of ports. show ports {<portlist> | all} {description | err_disabled | Syntax linkup_time | auto_negotiation | media_type} The show ports command displays the current configuration of a Description port or range of ports.
Page 64
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To delete the description of ports 1-3: DES-1210-52/ME:5# delete ports 1-3 description Command: delete ports 1-3 description DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide LOOPBACK DETECTION COMMANDS The Loopback Detection commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable loopdetect disable loopdetect config loopdetect mode...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To disable the loopback detection feature on the Switch: DES-1210-52/ME:5# disable loopdetect Command: disable loopdetect Success. DES-1210-52/ME:5# config loopdetect mode Purpose To configure the loop back detection mode to be portbase or vlanbase on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# config loopdetect Purpose To configure the loop back detection interval time and recover time on the Switch. config loopdetect interval_time <value 1-32767> Syntax lbd_recover_time [0 | <value 60-1000000>] Description The config loopdetect command configures the loop back detection interval time and recover time on the Switch.
Page 68
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Loopdetect Interval : 100 Recover Time : 60 DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DOS PREVENTION COMMANDS The DoS Prevention commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [ {land_attack | blat_attack | smurf_attack | tcp_null_scan | tcp_xmascan | config dos_prevention tcp_synfin | tcp_syn_srcport_less_1024} | all] {action [ drop | mirror <port>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide rx_rate [no_limit | <value (64-1024000)>] – controls the rate of the received DoS attack packets. If not specified, the default action is drop. state [enable | disable]- Enable or disable DoS prevention.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To display DoS prevention information for Land Attack: DES-1210-52/ME:5# show dos_prevention land_attack Command: show dos_prevention land_attack DosType State Action ---------------------------- ----------- --------------------- Land Attack Enabled Drop DES-1210-52/ME:5# enable dos_prevention trap_log Purpose Used to enable DoS prevention trap log.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide PPPOE CIRCUIT ID INSERTION COMMANDS PPPoE Circuit ID Insertion is used to produce the unique subscriber mapping capability that is possible on ATM networks between ATM-DSL local loop and the PPPoE server. The PPPoE server will use the inserted Circuit Identifier sub-tag of the received packet to provide AAA services (Authentication, Authorization and Accounting).
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# config pppoe circuit_id_insertion ports Purpose Used to enable and disable PPPoE circuit identifier insertion on a per port basis and specify how to encode the circuit ID option. Syntax config pppoe circuit_id_insertion ports <portlist> [ circuit_id [ mac | ip | udf <string 32>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide the global state configuration of the PPPoE circuit ID insertion function. Parameters None. Restrictions None. Example usage: To view the global PPPoE ID insertion state: DES-1210-52/ME:5# show pppoe circuit_id_insertion Command: show pppoe circuit_id_insertion...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DHCP SERVER SCREENING COMMANDS The DHCP server screenint commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Due to this function allow you not only to restrict all DHCP Server packets but also to receive any...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config filter dhcp_server log state Purpose To enable or disable the DHCP server log on the Switch. Syntax config filter dhcp_server log state [enable | disable] The config filter dhcp_server log state command is used to Description enable or disable the Filter DHCP server log state.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Description The show dhcp_server screening command is used to display current DHCP server screening information on the switch. Parameters None. Restrictions None. Example usage: To display the DHCP server screening information on the switch:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To create an entry from the DHCPv6 server filter list in the Switch’s database: DES-1210-52/ME:5# create filter dhcpv6_server permit_entry 3000::1 ports 1-3 Command: create filter dhcpv6_server permit_entry 3000::1 ports 1-3 Success. DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# config filter dhcpv6_server log state Purpose To enable or disable the DHCPv6 server log on the Switch. Syntax config filter dhcpv6_server log state [enable | disable] The config filter dhcpv6_server log state command is used to Description enable or disable the Filter DHCPv6 server log state.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide IP-MAC-PORT BINDING COMMANDS The IP network layer uses a four-byte address. The Ethernet link layer uses a six-byte MAC address. Binding these two address types together allows the transmission of data between the layers. The primary purpose of IP-MAC-port binding is to restrict the access to a switch to a number of authorized users.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: create address_binding ip_mac ipaddress 10.0.0.21 mac_address 00-00-00-00-01-02 port 3 Success. DES-1210-52/ME:5# config address_binding ip_mac ports Purpose Used to configure an IP-MAC-port binding state to enable or disable for specified ports. Syntax config address_binding ip_mac ports [<portlist>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: config address_binding ip_mac log all Success. DES-1210-52/ME:5# show address_binding ip_mac log Purpose Used to display an IP-MAC-port binding IP MAC log information. Syntax show address_binding ip_mac log The show address_binding ip_mac log command is used to Description display an IP-MAC-port binding IP MAC log information.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide IPv6 addresses. Syntax config address_binding auto_scan ipv6address from_ip <ipv6addr> to_ip <ipv6addr> The config address_binding auto_scan command is used to Description configure the IP-MAC-port binding auto scan for specified IPv6 addresses. <ipv6addr> − Specifies a range of IPv6 addresses for address Parameters binding auto scan on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show address_binding auto_scan list Purpose Used to display IP-MAC-port binding entries. Syntax show address_binding auto_scan list Description This show address_binding auto_scan list command is used to display auto scan list of address binding on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only administrator or operate-level users can issue this command. Example usage: To disable the DHCP snooping of address binding for port 3~5 on the Switch: DES-1210-52/ME:5# disable address_binding dhcp_snoop ports 4 Command: disable address_binding dhcp_snoop ports 4 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide port <portlist> – Specifies the ports on the device to be displayed. Restrictions None. Example usage: To display DHCP snoop of address binding max entries of port 1~5 on the Switch: DES-1210-52/ME:5# show address_binding dhcp_snoop max_entry...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: disable address_binding dhcp_pd_snoop Success. DES-1210-52/ME:5# show address_binding dhcp_pd_snoop Purpose Used to display address binding DHCPv6 PD Snooping. Syntax show address_binding dhcp_pd_snoop {binding_entry | ports <portlist>} Description This show address_binding dhcp_pd_snoop command is used to display IP-MAC-port binding DHCPv6 PD snooping.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide disable address_binding roaming Purpose Used to disable address binding roaming. Syntax disable address_binding roaming This disable address_binding roaming command is used to Description disable IP-MAC-port binding roaming. Parameters None. Restrictions Only administrator or operate-level users can issue this command.
Page 92
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only administrator or operate-level users can issue this command. Example usage: To clear DHCP IPv4 snooping entries on ports 1-3: DES-1210-52/ME:5# clear address_binding dhcp_snoop binding_entry ports 1-3 Command: clear address_binding dhcp_snoop binding_entry ports 1-3 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide NETWORK MANAGEMENT (SNMP) COMMANDS The Switch supports the Simple Network Management Protocol (SNMP) versions 1, 2c, and 3. Users can specify which version of the SNMP users want to use to monitor and control the Switch. The three versions of SNMP vary in the level of security provided between the management station and the network device.
Only administrator, operate or power user-level users can issue this command. Example usage: To create an SNMP user on the Switch: DES-1210-52/ME:5# create snmp user dlink sw22 v3 MD5 1234 DES 2233 Command: create snmp user dlink sw22 v3 MD5 1234 DES 2233...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# delete snmp user Purpose To remove an SNMP user from an SNMP group and also to delete the associated SNMP group. delete snmp user <username 32> [v1 | v2c | v3]...
Only administrator, operate or power user-level users can issue this command. Example usage: To create an SNMP view: DES-1210-52/ME:5# create snmp view dlink 1.3.6 1.1.1 view_type excluded Command: create snmp view dlink 1.3.6 1.1.1 view_type excluded Success. DES-1210-52/ME:5# delete snmp view Purpose To remove an SNMP view entry previously created on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Read/write or read-only level permission for the MIB objects accessible to the SNMP community. <community_string 32> − A string of up to 32 alphanumeric Parameters characters that is used to identify members of an SNMP community.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide characters that is used to identify members of an SNMP community. This string is used like a password to give remote SNMP managers access to MIB objects in the Switch’s SNMP agent.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example usage: To display the current name of the SNMP engine on the Switch: DES-1210-52/ME:5# show snmp engineID Command: show snmp engineID Default SNMP Engine ID : 4445532d313231...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide encryption of packets sent between the Switch and a remote SNMP manager. auth_priv − Specifies that authorization is required, and that packets sent between the Switch and a remote SNMP manger are encrypted.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# show snmp global state Purpose To display the global state of SNMP currently configured on the Switch. show snmp global state Syntax The show snmp global state command displays the global state of Description SNMP groups currently configured on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show snmp groups Command: show snmp groups SNMP Group Table Group Name Read View Write View Notify View Security Model Security Level ------------------ -------------- ---------------- --------------- ---------------------- ----------------- AuthPriv ReadOnly ReadWrite...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide encryption of packets sent between the Switch and a remote SNMP manager. auth_nopriv − Specifies that authorization is required, but there is no encryption of packets sent between the Switch and a remote SNMP manager.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide <ipaddr> − The IP address of a remote SNMP manager that Parameters receives SNMP traps generated by the Switch’s SNMP agent. Restrictions None. Example usage: To display the currently configured SNMP hosts on the Switch:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide identifies user name of an SNMP community. This string is used like a password to give remote SNMP managers access to MIB objects in the Switch’s SNMP agent. noauth_nopriv − Specifies that there is no authorization and no encryption of packets sent between the Switch and a remote SNMP manager.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide that are designated as recipients of SNMP traps generated by the Switch’s SNMP agent. <ip6_addr> − The IPv6 address of a remote SNMP manager that Parameters receives SNMP traps generated by the Switch’s SNMP agent.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only administrator or operator level users can issue this command. Example usage: To disable the trusted host on the Swtich: DES-1210-52/ME:5# disable trusted_host Command: disable trusted_host Success. DES-1210-52/ME:5# create trusted_host Purpose To create a trusted host.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show trusted_host Purpose To display a list of trusted hosts entered on the Switch using the create trusted_host command above. show trusted_host Syntax The show trusted_host command displays a list of trusted hosts...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# enable snmp authenticate_traps Purpose To enable SNMP authentication traps support. enable snmp authenticate_traps Syntax The enable snmp authenticate_traps command enables SNMP Description authentication trap support on the Switch. Parameters None. Restrictions Only Administrator or operator-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show snmp traps Command: show snmp traps SNMP Traps : Enable SNMP Authentication Traps : Enable System Device Bootup : Enable Fiber Port Link Up / Link Down : Enable Twisted Pair Port Link Up / Link Down...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To disable the SNMP link change trap function: DGS-1210-28P/ME:5# disable snmp linkchange_traps Command: disable snmp linkchange_traps Success. DGS-1210-28P/ME:5# config snmp linkchange_traps ports Purpose To configure SNMP traps support on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Port 02: Disabled Port 03: Disabled Port 04: Disabled Port 05: Disabled Port 06: Disabled Port 07: Disabled Port 08: Enabled Port 09: Enabled Port 10: Enabled Port 11: Disabled Port 12: Disabled...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide characters can be used. <string 128> − A maximum of 128 characters is allowed. A NULL Parameters string is accepted if there is no location desired. Restrictions Only Administrator or operator-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# config snmp coldstart_traps Purpose To enable or disable the cold start traps of SNMPon the Switch. config snmp coldstart_traps [enable | disable] Syntax The config snmp coldstart_traps command enable or disable the Description cold start traps of the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide enable snmp DHCPv6_screening traps Syntax The enable snmp DHCPv6_screening traps command enables Description SNMP DHCPv6 screening traps support on the Switch. Parameters None. Restrictions Only Administrator or operator-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide The disable snmp firmware_upgrade_state traps command Description disables SNMP firmware upgrade state traps support on the Switch. Parameters None. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To disable SNMP firmware upgrade state traps support on the Switch:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To enable SNMP RSTP port state change traps support on the Switch: DES-1210-52/ME:5# enable snmp rstpport_state_change traps Command: enable snmp rstpport_state_change traps Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide disable snmp duplicate_IP_detected traps Purpose To disable SNMP duplicate IP detected traps support on the Switch. disable snmp duplicate_IP_detected traps Syntax The disable snmp duplicate_IP_detected traps Description command disables SNMP duplicate IP detected traps support on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DOWNLOAD/UPLOAD COMMANDS The Download/Upload commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [cfg_fromTFTP [<ipaddr> | <ipv6_addr>] <path_filename 64> config_id <value 1- download 2>] | [firmware_ fromTFTP [<ipaddr>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide file, up to 64 characters, on the TFTP server. For example, C:\ DES- 1210-52ME-C1-20-01-B052-ALL.hex. image_id <value 1-2> − Specify the image id to be download. Restrictions Only Administrator or operator-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide must be on the same IP subnet as the Switch. <ipv6_addr> − The IPv6 address of the TFTP server. The TFTP server must be on the same IP subnet as the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show firmware information Command: show firmware information Current : image one Configured : image one IMAGE ONE Version : 20.01.B054 Size : 8640608 Bytes Updated Time : 01/01/2014 00:04:48 From : 10.90.90.98...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide command-start # User Account disable password encryption # Basic config syslogintimeout 5 config sysgroupinterval 0 enable web 80 enable clipaging config command_prompt default CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a ALL...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DHCP RELAY COMMANDS The DHCP Relay commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable dhcp_relay disable dhcp_relay config dhcp_relay port <portlist>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config dhcp_relay port To enable or disable the ports of DHCP Relay server. Purpose Syntax config dhcp_relay port <portlist> state [enable | disable] The config dhcp_relay port command is used to enable or disable Description the ports of DHCP Relay server.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config dhcp_relay delete ipif System Purpose To delete a DHCP server from the DHCP Relay server list. config dhcp_relay delete ipif System <ipaddr> Syntax The config dhcp_relay delete ipif System command deletes a Description DHCP servers defined as a DHCP Relay server.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide vlanid <vidlist> - Specifies the id of VLAN to be configured. [enable | disable] – Specifies the VLAN of DHCP Relay to be enabled or disabled. Restrictions Only Administrator, operator or power user-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide messages between DHCP server and client. When the relay agent receives the DHCP request, it adds the option 82 information, and the IP address of the relay agent (if the relay agent is configured), to the packet.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: config dhcp_relay port_option_82 1 circuit_id vendor3 12345678 Success. DES-1210-28/ME:5# show dhcp_relay port_option_82 Purpose display the current DHCP Relay option 82 information of each port show dhcp_relay port_option_82 {<portlist>} Syntax The show dhcp_relay port_option_82 command...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator, operator or power user-level users can issue this command. Example usage: To disable the DHCP Local Relay: DES-1210-52/ME:5# disable dhcp_local_relay Command: disable dhcp_local_relay Success. DES-1210-52/ME:5# config dhcp_local_relay port Purpose To enable or disable the ports of DHCP Local Relay.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide status by VLAN name or VLAN ID. Restrictions Only Administrator, operator or power user-level users can issue this command. Example usage: To disable the VLAN id 1 from VLAN of DHCP Local Relay:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To enable DCHPv6 Relay on the Switch: DES-1210-52/ME:5# enable dhcpc6_relay Command: enable dhcpc6_relay Success. DES-1210-52/ME:5# disable dhcpv6_relay Purpose To disable DHCPv6 Relay function on the Switch disable dhcpv6_relay Syntax The disable dhcpv6_relay command is used to disable the Description DHCPv6 relay global state on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DHCPv6 Relay Option37 Remote ID Type : default DHCPv6 Relay Option37 Remote ID : 00-01-02-03-04-05 --------------------------------------------------------------- IP Interface : Syetem Server Address Total Entries : 0 DES-1210-52/ME:5# config dhcpv6_relay Purpose Used to add or delete a destination IP address to or from the switch’s DHCPv6 relay table.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: config dhcpv6_relay hop_count 3 Success. DES-1210-52/ME:5# config dhcpv6_relay option_18 Purpose Used to configure the processing of Option 18 for the DHCPv6 relay function. Both the DHCPv6 relay and DHCPv6 local relay functions use the same Interface ID format.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide option 38 field before being relayed to the server. When the state is disabled, the DHCP packet is relayed directly to the server. subscriber_id [defult | user_define] - Use the user-defined string as the subscriber ID.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide 17 1 CPU PROTECTION COMMANDS The CPU Protection commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable cpu_protect disable cpu_protect config cpu_protect [arp | bpdu | icmp | igmp | snmp] pps [<value>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# disable cpu_protect Command: disable cpu_protect Success. DES-1210-52/ME:5# config cpu_protect type Purpose To configure the CPU protection packet type on the Switch. config cpu_protect type [arp | bpdu | icmp | igmp | snmp] pps Syntax [<value>...
Page 149
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show cpu_protect Command: show cpu_protect CPU Protect State : Enabled CPU Protect Type Rate Limit(pps) ------------------------- ------------------------ no limit BPDU no limit ICMP no limit IGMP no limit SNMP no limit...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide GRATUITOUS ARP COMMANDS The Gratuitous ARP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config gratuitous_arp [enable | disable] send ipif_status_up...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config gratuitous_arp send dup_ip_detected Purpose Used to enable or disable the sending of gratuitous ARP requests while duplicate IP addresses are detected. Syntax config gratuitous_arp send send dup_ip_detected [enable | disable]...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To enable learning of ARP entries based on the received gratuitous ARP packets: DES-1210-52/ME:5# config gratuitous_arp learning enable Command: config gratuitous_arp learning enable Success! DES-1210-52/ME:5# enable gratuitous_arp log Purpose Used to enable the gratuitous ARP log.
0 means it will not send gratuitous ARP periodically. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To configure gratuitous ARP intervals for the Switch: DES-1210-52/ME:5# config gratuitous_arp send periodically ipif rrd2 interval 100...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide 19 1 POWER SAVING COMMANDS The Power Saving commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config power_saving [hibernation | led | length_detection | port] [enable | disable] mode [hibernation | led [all | <portlist>] | port [all | <portlist>]] [add | delete] time_range1...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide | <portlist>]] [add | delete] time_range1 <range_name 20> time_range2 <range_name 20> {clear_time_range} The config power_saving command is used to configure the power Description saving on the switch. hibernation – Configure the hibernation.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide NETWORK MONITORING COMMANDS The Network Monitoring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter show packet ports <portlist> show error ports <portlist>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide The show packet ports command displays statistics about packets Description sent and received by ports specified in the port list. The results are separated into three tables, labeled A, B, and C in the window below.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Port Number : 1 RX Frames TX Frames ------------------ ------------------- CRC Error Excessive Deferral Undersize CRC Error Oversize Late Collision Fragment Excessive Collision 0 Jabber Single Collision Drop Pkts Collision DES-1210-52/ME:5# show utilization Purpose To display real-time port utilization statistics.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh clear counters To clear the Switch’s statistics counters. Purpose clear counters{ports <portlist>} Syntax The clear counters command clears the counters used by the Description Switch to compile statistics.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide clear log Syntax The clear log command clears the Switch’s history log. Description Parameters None. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To clear the log information:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only Administrator or operator-level users can issue this command. Example usage: To enable the syslog function on the Switch: DES-1210-52/ME:5# enable syslog Command: enable syslog Success. DES-1210-52/ME:5# disable syslog Purpose To disable the system log from being sent to a remote host.
Restrictions Only Administrator or operator-level users can issue this command. Example usage: To configure a syslog host: DES-1210-52/ME:5# config syslog host 1 severity all facility local0 Command: config syslog host 1 severity all facility local0 Success. DES-1210-52/ME:5# delete syslog host Purpose To remove a previously configured syslog host from the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide --------- ----------------------- ----------- ------------ ------------- ----------- 1.1.2.1 Local0 Enabled Total Entries : 1 DES-1210-52/ME:5# cable diagnostic port Purpose To determine if there are any errors on the copper cables and the position where the errors may have occurred.
Page 169
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only Administrator or operator-level users can issue this command. Example usage: To configure the system login timeout: DES-1210-52/ME:5# config syslogintimeout 30 Command: config syslogintimeout 30 Success. DES-1210-52/ME:5# config sysgroupinterval Purpose To configure the system group interval to optimal frequency.
Page 170
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide SPANNING TREE COMMANDS The Spanning Tree commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter {maxage <value 6-40> | hellotime <value 1-10> | forwarddelay <value 4-30>| config stp txholdcount <value 1-10>}...
Only administrator-level users can issue this command. Example usage: To configure STP with maxage 18 and hellotime 2: DES-1210-52/ME:5# config stp hellotime 2 forwarddelay 4 maxage 6 txholdcount 2 Command: config stp hellotime 2 forwarddelay 4 maxage 6 txholdcount 2 Success.
Page 173
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide auto – Automatically sets the speed for forwarding packets to the specified port(s) in the list for optimal efficiency. Default port cost:10Mbps port = 2000000. 100Mbps port = 200000. Gigabit port = 20000. Port-channel = 20000.
Only administrator or operator-level users can issue this command. Example usage: To configure STP with path cost 19 and state enable for ports 1-3: DES-1210-52/ME:5# config stp ports 1-3 externalcost 19 state enable Command: config stp ports 1-3 externalcost 19 state enable Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config stp priority Purpose To update the STP instance configuration. config stp priority <value 0-61440> instance_id <value 0-63> Syntax The config stp priority command updates the STP instance Description configuration settings on the Switch. The MSTP uses the priority in selecting the root bridge, root port and designated port.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide disable stp Syntax The disable stp command sets the Spanning Tree Protocol to be Description globally disabled on the Switch. Parameters None. Restrictions Only administrator-level users can issue this command. Example usage:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show stp ports To display the Switch’s current instance_id configuration. Purpose show stp ports {<portlist>} Syntax The show stp ports command displays the STP Instance Settings Description and STP Instance Operational Status currently implemented on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters <value 1-63> - The value of the instance ID to be created. Restrictions Only administrator-level users can issue this command. Example usage: To create instance id 1: DES-1210-52/ME:5# create stp instance_id 1...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide instance_id. remove_vlan − Along with the vid_range <vidlist> parameter, this command will remove VIDs to the previously configured STP instance_id. <vidlist> − Specify the VID range from configured VLANs set on the Switch.
Example usage: To designate ports 1 through 5 with instance ID 1, to have an auto internalCost and a priority of 16: DES-1210-52/ME:5# config stp mst_ports 6-8 instance_id 1 internalCost auto priority 16 Command: config stp mst_ports 6-8 instance_id 1 internalCost auto priority 16 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config stp trap Purpose To configure the sending state for STP traps. config stp trap {new_root [enable | disable] | topo_change Syntax [enable | disable]} The config stp mst_ports command is used to configure the Description sending state for STP traps.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide FORWARDING DATABASE COMMANDS The Forwarding Database commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create fdb <vlan_name 32> <macaddr> port <port 1-52>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide port <port 1-52> − The port number corresponding to the MAC destination address. The Switch will always forward traffic to the specified device through this port. Restrictions Only Administrator or operator-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide forwarding table. <portlist> − A port or range of ports to be configured. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To configure multicast MAC forwarding: DES-1210-52/ME:5# config multicast_fdb 1 00-00-00-01-02-03 Command: config multicast_fdb 1 00-00-00-01-02-03 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide <vlan_name 32> − The name of the VLAN on which the MAC Parameters address resides. <macaddr> − The MAC address to be removed from the forwarding table. Restrictions Only Administrator or operator-level users can issue this command.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide clear flood_fdb Syntax The clear flood_fdb command clears dynamically learned entries Description from the Switch’s forwarding database. Parameters None. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To clear all FDB dynamic entries:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide the forwarding table. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To display multicast MAC address table: DES-1210-52/ME:5# show multicast_fdb Command: show multicast_fdb Static Multicast Table ------------------------------------ Total Mac Addresses displayed: 0...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups Forward Unregistered Groups...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# show auto_fdb Purpose To display a static entry in the auto forwarding table (database). show auto_fdb {<ipaddr>} Syntax The show auto_fdb command displays a static entry in the Description multicast MAC address forwarding table (database).
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide BROADCAST STORM CONTROL COMMANDS The Broadcast Storm Control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [<portlist> | all] {[action [drop | shutdown] | countdown [0 | <minutes 5-30>] | config traffic control broadcast | multicast | unicast | threshold <value 0- 1024000>...
Only administrator or operator-level users can issue this command. Example usage: To configure traffic control and enable broadcast storm control system wide: DES-1210-52/ME:5# config traffic control all multicast enable unicast disable broadcast enable threshold 64 Command: config traffic control all multicast enable unicast disable broadcast e nable threshold 64 *Note: Setting count down for drop mode port was ignored.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: show traffic control 1-3 Traffic Storm Control Trap : [None] Port Thres Broadcast Multicast Unicast Action Count Time hold Storm Storm Storm down Interval ---- ------- ------------- ------------ --------- ----------- ---------...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide PASSWORD RECOVERY COMMANDS The Password Recovery commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable password_recovery disable password_recovery show password_recovery...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# disable password_recovery Command: disable password_recovery Success. DES-1210-52/ME:5# show password_recovery Purpose To show the password recovery mode on the Switch. show password_recovery Syntax The show password_recovery command is used to display the Description password recovery mode on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide QOS COMMANDS The QoS commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config scheduling <class_id 0-7> weight <value 1-55> show scheduling config [<portlist>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command Parameter protocol_mapping config cos vid <vlanid 1-4094> class <class_id 0-3> vlanid_mapping show cos {vid <vlanid 1-4094>} vlanid_mapping delete cos vid <vlanid 1-4094> vlanid_mapping config cos tos value <value 0-7> class <priority 0-7>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config scheduling <class_id 0-7> weight <value 1-55> Syntax The config scheduling command configures traffic scheduling for Description each of the Switch’s QoS queues. The Switch contains four hardware classes of service. Incoming packets must be mapped to one of these four hardware queues.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide the four priority classes of service on the Switch. The Switch empties the four hardware queues in order, from the highest priority (class 3) to the lowest priority (class 0). Parameters None.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config bandwidth_control all rx_rate 100 tx_rate no_limit Command: config bandwidth_control all rx_rate 100 tx_rate no_limit Success. DES-1210-52/ME:5# show bandwidth_control Purpose To display bandwidth control settings on the Switch. show bandwidth control {[<portlist> | all]}...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config cos mac_mapping destination_addr 00-00-00- 01-02-03 class 2 Command: config cos mac_mapping destination_addr 00-00-00-01-02-03 class 2 Success. DES-1210-52/ME:5# show cos mac_mapping Purpose To display the CoS MAC mapping method. show cos mac_mapping {destination_addr <macaddr>}...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config cos ip_mapping Purpose To configure the CoS IP mapping method. config cos ip_mapping destination_ip <ipaddr> class <class_id Syntax 0-3> The config cos ip_mapping command is used to configure the CoS Description IP mapping method on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide delete cos ip_mapping Purpose To remove the CoS IP mapping method. delete cos ip_mapping destination_ip <ipaddr> Syntax The delete cos ip_mapping command is used to delete the CoS IP Description mapping method on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide The show cos ipv6_mapping command is used to display the CoS Description MAC mapping method on the Switch. Parameters <ipv6addr> - Specifies the IPv6 address to be displayed. For example, 3000::1. Restrictions None.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only administrator or operator-level users can issue this command. Example usage: To configure the CoS IPv6 TC mapping on the Switch: DES-1210-52/ME:5# config cos ipv6_tc_mapping trafficclass 1 class 2 Command: config cos ipv6_tc_mapping trafficclass 1 class 2 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide ---------------------------------- DES-1210-52/ME:5# config cos mapping Purpose To configure the method of which incoming packets will be identified for the CoS to port mapping feature. config cos mapping port [<portlist> | all] [802.1p | dscp_tos |...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide 802.1p DSCP 802.1p DSCP 802.1p DSCP DES-1210-52/ME:5# config cos protocol_mapping Purpose To configure the CoS protocol mapping method on the Switch. config cos protocol_mapping protocol <ip_protocol 1-255> Syntax class <class_id 0-3> The config cos protocol_mapping command is used to configure Description the CoS protocol mapping method on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# delete cos protocol_mapping Purpose To delete the CoS protocol mapping between an incoming packet’s 802.1p priority value. delete cos protocol_mapping protocol <ip_protocol 1-255> Syntax The delete cos protocol_mapping command is used to delete the Description CoS protocol mapping between an incoming packet’s 802.1p priority...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show cos vlanid_mapping Purpose To display the CoS VLAN id mapping information between an incoming packet’s 802.1p priority value. show cos vlanid_mapping {vid <vlanid 1-4094>} Syntax The show cos vlanid_mapping command is used to display the Description CoS VLAN id mapping information between an incoming packet’s...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config cos tos value <value 0-7> class <priority 0-7> Syntax The config cos tos value command is used to configure the CoS Description tos on the Switch. Parameters <value 0-7> - Specifies the value of the Switch’s tos queue.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config cos tcp_port_mapping Purpose To configure the CoS TCP port mapping on the Switch. config cos tcp_port_mapping destination_port <value 0-65535> Syntax class <class_id 0-3> The config cos tcp_port_mapping command is used to configure Description the CoS TCP port mapping on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide The delete cos tcp_port_mapping command is used to delete the Description CoS TCP port mapping information on the Switch. Parameters <value 0-65535> - Specifies the mapped tcp port information to be deleted.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions None. Example usage: To display the CoS UDP port mapping on the Switch: DES-1210-52/ME:5# show cos udp_port_mapping Command: show cos udp_port_mapping UDP Port Class ------------------------------------------- DES-1210-52/ME:5# delete cos udp_port_mapping Purpose To delete the CoS UDP port mapping information on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide <priority 0-7> − The 802.1p priority value (0 to 7) to map to one of Parameters the Switch’s four hardware priority classes of service. <class_id 0-7> − The Switch’s hardware priority class of service (0 to 3) to map to the 802.1p priority value specified above.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Priority-6 -> <Class-6> Priority-7 -> <Class-7> DES-1210-52/ME:5# config 802.1p default_priority Purpose To assign an 802.1p priority tag to an incoming untagged packet that has no 802.1p priority tag. config 802.1p default_priority [<portlist> | all] <priority 0-7>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config scheduling_mechanism Purpose To configure the scheduling mechanism for the QoS function. config scheduling_mechanism [strict | wrr] Syntax The config scheduling_mechanism command configures the Description scheduling mechanism for the QoS function. It allows the user to select between a round robin (WRR) and a strict mechanism for emptying the priority classes of service of the QoS function.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example usage: To show the scheduling mechanism: DES-1210-52/ME:5# show scheduling_mechanism Command: show scheduling_mechanism QOS Scheduling_mechanism scheduling_mechanism : Strict Priority DES-1210-52/ME:5# config dscp mode Purpose To enable setting the DSCP User Priority...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To configure the DSCP mapping with value 10 and class 2: DES-1210-52/ME:5# config dscp_mapping dscp_value 10 class 2 Command: config dscp_mapping dscp_value 10 class 2 Success. DES-1210-52/ME:5# show dscp_mapping Purpose To display the setting of DSCP mapping.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide RMON COMMANDS The RMON commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable rmon disable rmon <alarm_index 1-65535> <OID_variable 255> <interval 1-2147482647> [absolute | delta] rising-threshold <value 0-2147483647>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: enable rmon Success. DES-1210-52/ME:5# disable rmon Purpose To disable remote monitoring (RMON) status for the SNMP function. disable rmon Syntax The disable rmon command disables remote monitoring (RMON) Description status for the SNMP function on the Switch.
Only Administrator or operator-level users can issue this command. Example usage: To create a RMON collection stats on the Switch: DES-1210-52/ME:5# create rmon collection stats 100 port 1 owner dlink Command: create rmon collection stats 100 port 1 owner dlink Success.
Only Administrator or operator-level users can issue this command. Example usage: To create a RMON collection history on the Switch: DES-1210-52/ME:5# create rmon collection history 120 port 2 buckets 25 Command: create rmon collection history 120 port 2 buckets 25 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only Administrator or operator-level users can issue this command. Example usage: To create a RMON collection history on the Switch: DES-1210-52/ME:5# create rmon event 125 description linkrmon owner dlink Command: create rmon event 125 description linkrmon owner dlink Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Alarm table is empty Event table is empty Success. DES-1210-52/ME:5# show rmon statistics Purpose To display remote monitoring (RMON) statistics for the SNMP function. show rmon statistics {<stats_index 1-65535>} Syntax The show rmon command displays remote monitoring (RMON) Description status for the SNMP function on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide PORT MIRRORING COMMANDS The Port Mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable mirror disable mirror config mirror target <short 1-52>...
A target port cannot be listed as a source port. Only Administrator or operator-level users can issue this command. Example usage: To add the mirroring ports: DES-1210-52/ME:5# config mirror target 2 add source ports 8-10 both Command: config mirror target 2 add source ports 8-10 both Success. DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show mirror Purpose To show the current port mirroring configuration on the Switch. show mirror Syntax The show mirror command displays the current port mirroring Description configuration on the Switch. Parameters None.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide VLAN COMMANDS The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create vlan <string 32> tag <int 2-4094> type_1q_vlan_advertisement delete vlan [<vlan_name 32>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command Parameter show asymmetric_vlan enable pvid auto_assign disable pvid auto_assign show pvid auto_assign Each command is listed in detail, as follows: create vlan Purpose To create a VLAN on the Switch. create vlan <string 32> tag <int 2-4094>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To remove a vlan which VLAN ID is 2: DES-1210-52/ME:5# delete vlan vlanid 2 Command: delete vlan vlanid 2 Success. DES-1210-52/ME:5# config vlan Purpose To add additional ports to a previously configured VLAN and to modify a VLAN name.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide ingress_checking [enable | disable] | acceptable_frame [Tagged_Only | All_Frames] | pvid <vlanid 1-4094>] The config gvrp command configures the Group VLAN Registration Description Protocol on the Switch. The user can configure ingress checking and acceptable frame tagged only, the sending and receiving of GVRP information, and the Port VLAN ID (PVID).
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# enable gvrp Purpose To enable GVRP on the Switch. enable gvrp Syntax The enable gvrp command, along with the disable gvrp command Description below, is used to enable and disable GVRP on the Switch, without changing the GVRP configuration on the ports and the LAGs.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters <vlan_name 32> - Specify the VLAN name to be displayed. vlanid <vidlist> − Specify the VLAN id to be displayed. ports <portlist> − Specify the ports to be displayed. Restrictions None.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# delete dot1v_protocol_group all Command: delete dot1v_protocol_group all Success. DES-1210-52/ME:5# show dot1v_protocol_group Purpose To display the protocols defined in a protocol group. Syntax show dot1v_protocol_group {group_id <id 1-16> | group_name <name 32>}...
Example usage: To configure the group ID 4 to be associated with VLAN 2: DES-1210-52/ME:5# config port dot1v ports all add protocol_group group_id 4 vlan vlan2 Command: config port dot1v ports all add protocol_group group_id 4 vlan vlan2 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show gvrp Purpose To display the GVRP status for a port list or port channel on the Switch. show gvrp {<portlist>} Syntax The show gvrp command displays the GVRP status for a port list or Description a port channel on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide 10000 DES-1210-52/ME:5# enable vlan_trunk Purpose To enable VLAN trunking on the switch. Syntax enable vlan_trunk The enable vlan_trunk command, along with the disable Description vlan_trunk command below, is used to enable and disable VLAN trunking on the Switch, without changing the VLAN trunking configuration on the ports.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example usage: To display the Switch’s current VLAN_trunk settings: DES-1210-52/ME:5# show vlan_trunk Command: show vlan_trunk VLAN Trunk Status :Enable Member Ports :None DES-1210-52/ME:5# config vlan_trunk ports Purpose To configure VLAN Trunking port settings on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: enable asymmetric_vlan Warning: The settings of VLAN, IGMP Snooping,Management VLAN, 802.1v, and MAC Address Table will be reset to default. Success. DES-1210-52/ME:5# disable asymmetric_vlan Purpose To disable Asymmetric VLAN on the switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide enable pvid auto_assign Purpose To to enable auto assignment of PVID. Syntax enable pvid auto_assign The enable pvid auto_assign command enables the auto-assign of Description PVID. When this is enabled, PVID will be possibly changed by PVID or VLAN configuration.
Page 245
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. None. Restrictions Example usage: To display the auto-assign PVID state: DES-1210-52/ME:5# show pvid auto_assign Command: show pvid auto_assign PVID Auto-assignment: Enabled DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Q-IN-Q COMMANDS The Link Aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable qinq disable qinq show qinq {ports [<portlist> | all]} [<portlist>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide disable qinq Purpose To disable the Q-in-Q mode. disable qinq Syntax The disable qinq command creates a used to disable the Q-in-Q Description mode. All dynamically learned L2 address will be cleared. All dynamically registered VLAN entries will be cleared, GVRP will be disabled.
Only administrator or operator-level users can issue this command. Example usage: To configure port list 1 to 4 as NNI port, set outer TPID to 0x88a8: DES-1210-52/ME:5# config qinq ports 1-4 role nni outer_tpid 0x88a8 Command: config qinq ports 1-4 role nni outer_tpid 0x88a8 Success.
Only administrator or operator-level users can issue this command. Example usage: To create a VLAN translation on the Switch: DES-1210-52/ME:5# create vlan_translation ports 3-5 add cvid 2 svid 2 Command: create vlan_translation ports 3-5 add cvid 2 svid 2 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide LINK AGGREGATION COMMANDS The Link Aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create link_aggregation group_id <value 1-8> {type [lacp | static]} delete link_aggregation group_id <value 1-8>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only administrator or operator-level users can issue this command. Example usage: To create a link aggregation group: DES-1210-52/ME:5# create link_aggregation group_id 1 Command: create link_aggregation group_id 1 Success. DES-1210-52/ME:5# delete link_aggregation Purpose To delete a previously configured link aggregation group.
Link aggregation groups may not overlap. Example usage: To define a load-sharing group of ports, group-id 2 with group members ports 1-5: DES-1210-52/ME:5# config link_aggregation group_id 2 master_port 1 ports 1-5 Command: config link_aggregation group_id 2 master_port 1 ports 1-5 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide [enable | disable] – Enables or disables the link aggregation state. Parameters Restrictions Only administrator or operator-level users can issue this command. Example usage: To enable the link aggregation feature: DES-1210-52/ME:5# config link_aggregation state enable...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide BASIC IP COMMANDS The Basic IP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create ipif <ipif_name 12> <network_address> <vlan_name 32> state [enable | disable] delete ipif [<ipif_name 12>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide delete ipif Purpose To delete an IP interface on the switch. delete ipif [<ipif_name 12> | all] Syntax The delete ipif command will delete an IP interface. Description Parameters [<ipif_name 12> | all] - Specifies the IP interface name or all IP interface to be deleted.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# config ipif Purpose To configure the DHCPv6 client state for the interface. Syntax config ipif <ipif_name 12> ( [ipaddress <network_address>] [vlan <vlan_name 32>] [state [enable | disable]] | dhcp | ipv6 {ipv6address <ipv6networkaddr>...
Page 258
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide on the Switch. Parameters <string> - Specifies the IP interface name. Restrictions None. Example usage: To display IP interface settings: DES-1210-52/ME:5# show ipif Command: show ipif IP Setting Mode : Static Interface Name...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide BPDU ATTACK PROTECTION COMMANDS The BPDU Attack Protection commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config bpdu_protection [<portlist> | all ] [state [enable | disable] | mode [ drop | block | shutdown ]]...
Only administrator-level users can issue this command Example usage: To set the BPDU attack protection port state to enable and drop mode: DES-1210-52/ME:5# config bpdu_protection ports 1 state enable mode drop Command: config bpdu_protection ports 1 state enable mode drop Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# enable bpdu_protection Command: enable bpdu_protection Success. DES-1210-52/ME:5# disable bpdu_protection Purpose Used to globally disable BPDU attack protection on the Switch. disable bpdu_protection Syntax Description The disable bpdu_protection command is Use this to disable BPDU attack protection on the entire Switch.
Page 263
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show bpdu_protection Command: show bpdu_protection BPDU Protection Global Settings ------------------------------------------------------------------- BPDU Protection Status : Enabled BPDU Protection Recover Time : 60 seconds BPDU Protection Trap State : none BPDU Protection Log State...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide ETHERNET OAM COMMANDS The Ethernet OAM commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config ethernet_oam [<portlist> | all] mode [active | passive] {received_remote_loopback [ignore |...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide state [enable | disable] – Specifies the state to be enabled or disabled. Restrictions Only administrator or operator-level users can issue this command. Example usage: To configure ports 1 to 3 to OAM mode to active:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide all – Entering this command will set all ports on the system. critical_link_event [critical_event | dying_gasp] – Specifies the critical link event is critical event or dying GASP. notify_state [enable | disable] – Specifies to enable or disable the event notification.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide sizes between the peers. (5) OAM configuration revision: The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate that configuration changes have occurred, which might require the peer OAM entity to re-evaluate whether OAM peering is allowed.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide displayed. Restrictions None. Example usage: To show Ethernet OAM configuration of port 1: DES-1210-52/ME:5# show ethernet_oam ports 1 configuration Command: show ethernet_oam ports 1 configuration Port 1 ----------------------------------------------------------- : Enabled Mode : Active...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To show Ethernet OAM statistics of port 1: DES-1210-52/ME:5# show ethernet_oam ports 1 statistics Command: show ethernet_oam ports 1 statistics Port 1 -------------------------------------------------------------------- Information OAMPDU Tx Information OAMPDU Rx Unique Event Notification OAMPDU Tx...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide MAC NOTIFICATION COMMANDS The IGMP Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable mac_notification disable mac_notification config mac_notification [interval <int 1-2147483647>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide address notification without changing configuration. Parameters None. Restrictions Only administrator or operator-level users can issue this command. Example usage: To disable MAC notification without changing basic configuration: DES-1210-52/ME:5# disable mac_notification Command: disable mac_notification Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To enable port 7 for MAC address table notification: DES-1210-52/ME:5# config mac_notification ports 7 enable Command: config mac_notification ports 7 enable Success. DES-1210-52/ME:5# show mac_notification Used to display the Switch’s MAC address table notification global Purpose settings.
Page 274
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Port MAC Address Table Notification State ---- ---------------------------------------------------- Disabled Disabled Disabled Disabled Disabled DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide IGMP SNOOPING COMMANDS The IGMP Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [vlan_name <string 32> | vlanid <vidlist> | all] [host_timeout <sec 130-153025> | config igmp_snooping router_timeout <sec 60-600>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide state [enable | disable] − Enables or disables IGMP snooping for the specified VLAN. Restrictions Only administrator, operator or power user-level users can issue this command. Example usage: To configure the igmp snooping:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To configure the igmp snooping multicast VLAN: DES-1210-52/ME:5# config igmp_snooping multicast_vlan default state enable Command: config igmp_snooping multicast_vlan default state enable Success. DES-1210-52/ME:5# delete igmp_snooping multicast_vlan Purpose To remove an IGMP snooping multicast VLAN on the Switch.
Restrictions Only administrator or operator-level users can issue this command. Example usage: To add port 5 to static group 226.1.1.1 on VID 1: DES-1210-52/ME:5# config igmp_snooping static group vlanid 1 226.1.1.1 and 5 Success.DES-1210-52/ME:5# delete igmp_snooping static_group Purpose To delete the current IGMP snooping static group on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide static group to be displayed. <vlanid_list> − The VLAN id of IGMP snooping static group to be displayed. <ipaddr> − Specify the IP address of IGMP snooping static group to be displayed.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success.DES-1210-52/ME:5# config igmp_snooping data_driven_learning Purpose Used to configure the data driven learning of an IGMP snooping group. config igmp_snooping data_driven_learning Syntax max_learned_entry <integer 1-512> The config igmp_snooping data_driven_learning command Description configures the max learned entry of IGMP snooping data driven learning on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command: clear igmp_snooping data_driven_group all Success. DES-1210-52/ME:5# config router_ports Purpose To configure ports as router ports. config router_ports [vlan_name <string 32> | vlanid <vidlist> | Syntax all] [add | delete] <portlist> The config router_ports command designates a range of ports as Description being connected to multicast-enabled routers.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide all − Specifies all ports on the Switch to be configured. [add | delete] – Specifies whether to deny ports defined in the following parameter <portlist>, to the router port function. <portlist> − A port or range of ports that will be denied access as router ports.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide <portlist> − A port or range of ports to be displayed on the Switch. Restrictions Only administrator, operator or power user-level users can issue this command. Example usage: To display the IGMP access authentication:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide VLAN or forward mcrouter for IGMP Snooping on the Switch. Restrictions Only Administrator or operator-level users can issue this command. Example usage: TTo disable IGMP snooping on the Switch: DES-1210-52/ME:5# disable igmp_snooping Command: disable igmp_snooping Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Version Data Driven Learning Aged Out : Disable Data Driven Learning State : Disable CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a ALL show igmp_snooping group Purpose To display the current IGMP snooping group configuration on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide current IGMP snooping forwarding table entries currently configured on the Switch. vlan <vlan_name 32> − The name of the VLAN for which IGMP Parameters snooping forwarding table information is to be displayed. Up to 20 characters can be used.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show igmp_snooping multicast_vlan Purpose To display the IGMP snooping multicast vlan table entries on the Switch. show igmp_snooping multicast_vlan {<vlan_name 32>} Syntax The show igmp_snooping multicast_vlan command displays the Description current IGMP snooping forwarding table entries currently configured on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show router_ports Purpose To display the currently configured router ports on the Switch. show router_ports {vlan <vlan_name 32> | vlanid <vidlist> | Syntax static | dynamic | forbidden} The show router_ports command displays the router ports Description currently configured on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DIGITAL DIAGNOSTIC MONITORING COMMANDS The Digital Diagnostic Monitoring (DDM) commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter <portlist> [bias_current_threshold [high_alarm | low_alarm] | rx_power_threshold...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide MLD SNOOPING COMMANDS The MLD Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable mld_snooping {multicast_vlan | forward_mcrouter_only} disable mld_snooping {multicast_vlan | forward_mcrouter_only} [vlan_name <string 32>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide MLD multicast_vlan. Multiple multicast VLANs can be configured. When creating MLD multicast VLAN, it cannot duplicate with the VLAN entries in the existing 802.1Q VLAN database. The MLD Multicast VLAN snooping function co-exists with the 1Q VLAN snooping function.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide replace_source_ipv6 <ipv6addr> – With the MLD snooping function, the MLD report packet sent by the host will be forwarded to the source port. Before the forwarding of the packet, the source IP address in the join packet needs to be replaced by this IPv6 address.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide this command. Example usage: To delete a MLD multicast VLAN: DES-1210-52/ME:5# delete mld_snooping multicast_vlan mv1 Command: delete mld_snooping multicast_vlan mv1 Success. DES-1210-52/ME:5# config mld_snooping multicast_vlan_group Purpose To bind a multicast group profile to a multicast VLAN. The binding profile will affect the group joined to the multicast VLAN.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To display mld snooping multicast VLAN group: DES-1210-52/ME:5# show mld_snooping multicast_vlan_group Command: show mld_snooping multicast_vlan_group VID Vlan Name IP Range ---- -------------------------------- ----------------------------------------- DES-1210-52/ME:5# config mld_snooping mrouter_ports Purpose To enable mld mrouter ports.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide only to this previously created VLAN. vlanid <vidlist> – specifies that the mld snooping applies only to this previously created VLAN id. all – specifies that MLD snooping is to be configured for all VLANs on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide for expected packet loss on a subnet. The user may choose a value between 1 and 255 with a default setting of 2. If a subnet is expected to be lossy, the user may wish to increase this interval.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To enable the data driven learning of an MLD snooping group on the default VLAN: DES-1210-52/ME:5# config mld_snooping data_driven_learning vlan_name default state enable Command: config mld_snooping data_driven_learning vlan_name default state enable Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide all – Displays that MLD snooping which configured for all VLANs on the Switch. Restrictions None. Example usage: To show the MLD snooping: DES-1210-52/ME:5# show mld_snooping vlan_name default Command: show mld_snooping vlan_name default...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To display the MLD snooping forwarding: DES-1210-52/ME:5# show mld_snooping forwarding all Command: show mld_snooping forwarding all Total Entries : 0 DES-1210-52/ME:5# show mld_snooping group Purpose To display mld snooping group settings on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide LIMITED IP MULTICAST ADDRESS COMMANDS The 802.1X commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create [ipv4 | ipv6] profile_id <integer 1-24> profile_name <string 20>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide profile on the Switch. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To create an IPv6 multicast filtering profile on the Switch: DES-1210-52/ME:5# create mcast_filter_profile ipv6 profile_id 1 profile_name Command: create mcast_filter_profile ipv6 profile_id 1 profile_name rd2 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide name. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To configure the multicast address range 225.1.1.1 to 225.1.1.10 to the profile name “rd3” on the Switch: DES-1210-52/ME:5# config mcast_filter_profile profile_name rd3 add 225.1.1.11 225.1.1.20...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide profile_id [all | <integer 1-24>] − The profile id of the VLAN on which the multicast forwarding filtering database resides. profile_name <string 20> − The name of the VLAN on which the multicast forwarding filtering database resides.
Only Administrator or operator-level users can issue this command. Example usage: To configure ports 1 and 3 to set the IPv6 multicast address profile id 1: DES-1210-52/ME:5# config limited_multicast_addr ports 1,3 ipv6 add profile_id 1 Command: config limited_multicast_addr ports 1,3 ipv6 add profile_id 1 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide (v4) Permit (v4) Permit DES-1210-52/ME:5# config max_mcast_group Purpose Used to configure the maximum number of multicast groups that a port can join. config max_mcast_group ports <portlist> [ipv4 | ipv6] Syntax max_group <integer 1-512>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions Only Administrator, operator or power user-level users can issue this command. Example usage: To disable Layer 2 protocol tunnel of the Switch: DES-1210-52/ME:5# disable l2protocol_tunnel Command: disable l2protocol_tunnel Success. DES-1210-52/ME:5# config l2protocol_tunnel Purpose To configure Layer 2 protocol tunneling on ports.
Page 317
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide 2 protocol tunneling function on the Switch. nni – Specify to show UNI detail information, include tunneled and Parameters dropped PDU statistic. uni - Specify to show NNI detail information, include de-capsulated Layer 2 PDU PDU statistic.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide 802.1X COMMANDS The 802.1X commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable 802.1x disable 802.1x show 802.1x {ports <portlist>} auth_state show 802.1x...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Command Parameter guest_vlan create 802.1x user <username 15> show 802.1x user delete 802.1x user <username 15> config 802.1x capability [<portlist> | all] [authenticator | none] ports Each command is listed in detail, as follows: enable 802.1x...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Success. DES-1210-52/ME:5# show 802.1x Purpose To display the 802.1x server information on the Switch. show 802.1x Syntax Description The show 802.1x command displays the 802.1x Port-based Network Access control server application on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show 802.1x auth_state ports 1-5 Command: show 802.1x auth_state ports 1-5 Port Auth PAE State Backend State Port Status ------ ---------------------- -------------------- --------------- ForceAuth Success. Authorized ForceAuth Success. Authorized ForceAuth Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide reauthentications. ReAuthenticate: true/false − Shows whether or not to reauthenticate. ports <portlist> − Specifies a port or range of ports to be viewed. Parameters Restrictions None. Example usage: To display the 802.1x configurations of port 2: DES-1210-52/ME:5# show 802.1x auth_configuration ports 2...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide all – Specifies all of the ports on the Switch. default – Returns all of the ports in the specified range to their 802.1x default settings. port_control – Configures the administrative control over the authentication process for the range of ports.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide from a specified range of ports. port_based – Instructs the Switch to initialize 802.1x functions based Parameters only on the port number. Ports approved for initialization can then be specified. ports <portlist> – A port or range of ports to be configured.
1 and 255 seconds. Restrictions Only Administrator or operator-level users can issue this command. Example usage: To configure the RADIUS server communication settings: DES-1210-52/ME:5# config radius add 1 10.48.47.11 key dlink default Command: config radius add 1 10.48.47.11 key dlink default...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To configure the RADIUS settings: DES-1210-52/ME:5# config radius 1 ipaddress 10.48.47.11 Command: config radius 1 ipaddress 10.48.47.11 Success. DES-1210-52/ME:5# show radius Purpose To display the current RADIUS configurations on the Switch. Syntax...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide command. Example usage: To enable 802.1x forwarding EAPOL PDU DES-1210-52/ME:5# config 802.1x fwd_pdu system enable Command: config 802.1x fwd_pdu system enable Success. DES-1210-52/ME:5# show 802.1x fwd_pdu system status Purpose To display the 802.1x forwarding EAPOL PDU status on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# delete 802.1x guest_vlan default Command: delete 802.1x guest_vlan default Success. DES-1210-52/ME:5# config 802.1x guest_vlan ports Purpose Defines a port or range of ports to be members of the Guest VLAN. config 802.1x guest_vlan ports [<portlist> | all] state [enable |...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show 802.1x user Command: show 802.1x user Index Username ------------ --------------- dlink Total Entries: 1 Success. DES-1210-52/ME:5# delete 802.1x user Purpose Deletes network access to a 802.1x user. delete 802.1x user <username 15>...
Page 333
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config 802.1x capability ports all authenticator Command: config 802.1x capability ports all authenticator Success. DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide PORT SECURITY COMMANDS The Port Security commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [<portlist> | all] [admin_state [enable | disable] | max_learning_addr config port_security <max_lock_no 0-64>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide and on when the address is aged out. Restrictions Only administrator or operator-level users can issue this command Example usage: To configure port security: DES-1210-52/ME:5# config port_security admin_state enable max_learning_addr 5 lock_address_mode DeleteOnReset...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide delete port_security _entry Purpose To delete a port security entry by VLAN, VLAN ID, and MAC address. delete port_security_entry [vlan <vlan_name 32> | vlanid Syntax <vlanid 1-4094>] mac_address <macaddr> The delete port_security_entry command is used to delete a port Description security entry by VLAN, VLAN ID, and MAC address.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide TIME AND SNTP COMMANDS The Time and SNTP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter {primary [<ipaddr> | <ipv6addr>] | secondary [<ipaddr> | <ipv6addr>] | poll- config sntp interval <sec 30-99999>}...
Restrictions Only administrator or operator level users can issue this command. Example usage: To configure time zone settings: DES-1210-52/ME:5# config time_zone operator + hour 2 minute 30 Command: config time_zone operator + hour 2 minute 30 Success. DES-1210-52/ME:5# config dst...
Wednesday in October at 3:30 PM and add 30 minutes at the onset of DST: DES-1210-52/ME:5# config dst annual s_date 2 s_mth 4 s_time 3 end_date 2 e_mth 10 e_time 3 offset 30 Command: config dst annual s_date 2 s_mth 4 s_time 3 end_date 2 e_mth 10 e_time 3 offset 30 Success.
Page 342
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show time Command: show time Time information ------------------------------------------------------------------------------------------- Current Time Source : Local Current Time : 09 Jan 2012 15:56:02 GMT Time Zone offset : GMT +02:30 Daylight Saving Time Status...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide ARP COMMANDS The ARP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create ArpSpoofing ip_address <ipaddr> mac_address <macaddr> [<portlist> | all]...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To create an ARP Spoofing IP address on the Switch: DES-1210-52/ME:5# create ArpSpoofing ip_address 10.2.1.1 mac_address 00-00-00-01-01-2 all Command: create ArpSpoofing ip_address 10.2.1.1 mac_address 00- 00-00-01-01-2 all Success. DES-1210-52/ME:5# show ArpSpoofing Purpose To display the ARP Spoofing information on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To delete the ARP spoofing configuration: DES-1210-52/ME:5# create ArpSpoofing ip_address 10.2.1.1 mac_address 00-00-00-01-01-2 all Command: create ArpSpoofing ip_address 10.2.1.1 mac_address 00- 00-00-01-01-2 all Success. DES-1210-52/ME:5# config arp_aging time Purpose To configure the age-out timer for ARP table entries on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To remove dynamic entries in the ARP table: DES-1210-52/ME:5# clear arptable Command: clear arptable Success. DES-1210-52/ME:5# create arpentry Purpose To create an entry for ARP table on the Switch. create arpentry <ipaddr> <macaddr>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To display all ARP entries information on the Switch: DES-1210-52/ME:5# show arpentry information Command: show arpentry information ARP Configurations: ------------------- Maximum number of ARP request retries is 3 ARP cache timeout is 1800 seconds...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide ROUTING TABLE COMMANDS The Routing table commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create iproute default <ipaddr> {<value 1-254>}...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide delete iproute Used to delete an IP route entry from the Switch’s IP routing table. Purpose Syntax delete iproute {default} The delete iproute command will delete an existing IP route entry Description from the Switch’s IP routing table.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide STATIC MAC_BASED VLAN COMMANDS The Static MAC_based VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create mac_based_vlan <macaddr> [vlan <vlan_name 32> | vlanid <vlanid 1-4094>]...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide D-LINK UNIDIRECTIONAL LINK DETECTION (DULD) COMMANDS The D-Link Unidirectional Link Detection (DULD) commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [<portlist>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To enable unidirectional link detection on port 1: DES-1210-52/ME:5# config duld ports 1 state enable Command: config duld ports 1 state enable Success. DES-1210-52/ME:5# show duld ports Purpose To show unidirectional link detection information.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To configure the unidirectional link detection recovery time to 100 seconds: DGS-1210-28P/ME:5# config duld recover_timer 100 Command: config duld recover_timer 100 Success. DGS-1210-28P/ME:5# show duld recover_timer Purpose To display unidirectional link detection recover time.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide IPV6 NEIGHBOR DISCOVERY COMMANDS The IPv6 Neighbor Discovery commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create ipv6 ipif System <ipv6_addr> <mac_addr>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# create ipv6 neighbor_cache ipif System 3ffc::1 00:01:02:03:04:05 Command: create ipv6 neighbor_cache ipif System 3ffc::1 00:01:02:03:04:05 Success. DES-1210-52/ME:5# delete ipv6 neighbor_cache Purpose Used to remove a static neighbor on an IPv6 interface.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To show all neighbor cache entries on the switch: DES-1210-52/ME:5# show ipv6 neighbor_cache ipif all all Command: show ipv6 neighbor_cache ipif all all IPv6 Address Link-layer Addr State Interface ------------...
Only Administrator or operator-level users can issue this command. Example usage: To configure the retrans_time of IPv6 ND neighbor solicitation to be 100: DES-1210-52/ME:5# config ipv6 nd ns ipif System retrans_time 100 Command: config ipv6 nd ns ipif System retrans_time 100 Success.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# delete ipv6route default Command: delete ipv6route default Success. DES-1210-52/ME:5# show ipv6route Used to display a static IPv6 route entry from the Switch’s IP routing Purpose table. Syntax show ipv6route Description This delete ipv6route command will display an existing static IPv6 entry from the Switch’s IP routing table.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide disable ipif_ipv6_link_local_auto System Purpose Used to disable the autoconfiguration of the IPv6 link local address. Syntax disable ipif_ipv6_link_local_auto System This disable ipif_ipv6_link_local_auto System command will Description disable the automatic creation of an IPv6 link local address for the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide BANNER COMMANDS The Banner commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config log_save_timing [log_trigger | on_demand | time_interval <minutes 1-65535>]...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show log_save_timing Purpose Used to show the log save timing. Syntax show log_save_timing Description This command allows display of the log save timing on the Switch. Parameters None. Restrictions None. Usage Example:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show log Purpose Used to show the log. Syntax show log {index <value 1-500> - <value 1-500> | module <string 32> | severity [warning | all | informational]} Description This command allows display the log.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide COMMAND HISTORY LIST COMMANDS The Command History List commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter show command_history Each command is listed in detail, as follows: Purpose To display all commands in the Command Line Interface (CLI).
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide create ipv6 neighbor_cache ipif System 3000::2 00-00-00-11-22- show duld ports config duld ports all discovery_time shoc 5-65535> DES-1210-52/ME:5# Purpose To display all commands. Syntax The dir command displays all commands. Description Parameters None.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide SSH COMMANDS The SSH commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable ssh disable ssh config ssh algorithm [3DES | MD5 | RSA | SHA1] [disable | enable]...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show ssh server Command: show ssh server The SSH Server Configuration : Max Session Connection Timeout : 120 Authfail Attempts : 20 Rekey Timeout : never Success. DES-1210-52/ME:5# show ssh algorithm Purpose To display the SSH algorithm setting.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config ssh user Purpose To specify which SSH public key is manually configured. config ssh user <string 15> authmode [hostbased hostname Syntax <domain_name 32> hostname_IP <ip_addr> | password | publickey] The config ssh crypto command specifies which SSH public key is Description manually configured.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide SSL COMMANDS The SSL commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter {ciphersuite [DH-RSA-3DES-SHA1 | DH-RSA-DES-SHA1 | RSA-3DES-SHA1 | enable ssl...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# enable ssl Command: enable ssl Note: HTTP will be disabled if SSL is enabled. Success. DES-1210-52/ME:5# disable ssl Purpose To disable the SSL function on the Switch. disable ssl {ciphersuite [DH-RSA-3DES-SHA1 | DH-RSA-DES-...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To view the SSL status on the Switch: DES-1210-52/ME:5# show ssl Command: show ssl SSL Status Enabled RSA-NULL-MD5 0x0001 Enabled RSA-NULL-SHA1 0x0002 Enabled RSA-DES-SHA1 0x0004 Enabled RSA-3DES-SHA1 0x0008 Enabled DH-RSA-DES-SHA1...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide ACCESS AUTHENTICATION CONTROL COMMANDS The Access Authentication Control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter create authen_login <string 15>...
Page 379
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide affects the authentication result. For example, if a user enters a sequence of methods like tacacs – local, the Switch sends an authentication request to the first tacacs host in the server group. If...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config authen_login method_list_name Trinity method tacacs+ radius local Command: config authen_login method_list_name Trinity method tacacs+ radius local Success. DES-1210-52/ME:5# delete authen_login method_list_name Purpose To delete a previously configured user defined list of authentication methods for users logging on to the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To view all authentication login method list names: DES-1210-52/ME:5# show authen_login all Command: show authen_login all Method List Name Priority Method Name Comment -------------------------- ---------- --------------- ------------------ default local Keyword...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters <string 15> - Defines the authen_enable method_list_name to be created as a string of up to 15 alphanumeric characters. Restrictions Only Administrator-level users can issue this command. Example usage: To create a user-defined method list, named ‘Permit’ for promoting user privileges to Adminstrator privileges:...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide server_group <string 15> – Specifies the server group name for authentication. none – Specifies that no authentication is required to access the Switch. method_list_name <string 15> – Specifies a previously created authen_enable method_list_name.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# delete authen_enable method_list_name Permit Command: delete authen_enable method_list_name Permit Success. DES-1210-52/ME:5# show authen_enable Purpose To display the list of authentication methods for promoting normal user level privileges to Administrator level privileges on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. Restrictions Only Administrator-level users can issue this command. Example usage: To enable the authentication policy: DES-1210-52/ME:5# enable authen_policy Command: enable authen_policy Success. DES-1210-52/ME:5# disable authen_policy Purpose To disable the authentication policy on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide login – Configures an application for normal login on the user level, using a previously configured method list. enable – Configures an application for upgrading a normal user level to administrator privileges, using a previously configured method list.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config authen parameter Purpose To provide user to configure the authentication parameters on the Switch. config authen parameter [attempt <int 1-255> | Syntax response_timeout <int 0-255>] The config authen parameter attempt command provides user to Description configure the authentication parameters on the Switch.
Page 388
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide protocol [radius | tacacs+] {port <int 1-65535> | key [<string 254> | none] | timeout <int 1-255> | retransmit <int 1-255>} The create authen server_host command creates an Description authentication server host for the TACACS+/RADIUS security protocols on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Timeout - The time in seconds the Switch waits for the server host to reply to an authentication request. Retransmit - The value in the retransmit field denotes how many times the device resends an authentication request when the TACACS server does not respond.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Example usage: To delete a user-defined rd1 authentication server group: DES-1210-52/ME:5# delete authen server_group dlinkgroup Command: delete authen server_group dlinkgroup Success. DES-1210-52/ME:5# show authen server_group Purpose To view a user-defined authentication server group.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide enable admin Purpose To promote user level privileges to administrator level privileges. enable admin Syntax The enable admin command enables a user to be granted Description administrative privileges on to the Switch. After logging on to the Switch, users have only ‘user’...
Page 395
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config admin local_enable Command: config admin local_enable Enter the old password: Enter the case-sensitive new password:****** Enter the new password again for confirmation:****** Success. DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide LACP COMMANDS The LACP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config lacp port_priority <portlist> <value 0-65535> [timeout <long | short>] show lacp {<portlist>}...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters <portlist> - A port or range of ports whose LACP settings are to be displayed. If no parameter is specified, the system displays the current LACP status for all ports. Restrictions None.
Page 398
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config lacp_ports 1 mode active Command: config lacp_ports 1 mode active Success. DES-1210-52/ME:5#...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide LLDP COMMANDS The LLDP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter enable lldp disable lldp config lldp <sec 5-32768>...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Each command is listed in detail, as follows: enable lldp Purpose To enable LLDP on the switch. enable lldp Syntax The enable lldp command enables the Link Layer Discovery Description Protocol (LLDP) on the switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# config lldp message_tx_interval 10 Command: config lldp message_tx_interval 10 Success. DES-1210-52/ME:5# config lldp message_tx_hold_multiplier Purpose To define the lldp hold-multiplier on the switch. config lldp message_tx_hold_multiplier <int 2-10> Syntax Description The config lldp message_tx_hold_multiplier command specifies the amount of time the receiving device should hold a Link Layer Discovery Protocol (LLDP) packet before discarding it.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide config lldp tx_delay Purpose To configure the lldp tx_delay on the switch. Syntax config lldp tx_delay <sec 1-8192> The config lldp tx_delay command specifies the delay between Description Success.ive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB, use the lldp tx_delay command in global configuration mode.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Parameters None. Restrictions None. Example usage: To show LLDP settings: DES-1210-52/ME:5# show lldp Command: show lldp LLDP System Information Chassis Id Subtype : MAC Address Chassis Id : 00-01-02-03-04-05 System Name System Description : DES-1210-52/ME 7.00.004...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show lldp ports 1 Port ID ----------------------------------------------------------------- Admin Status : TX_and_RX Notification Status : Disable Advertised TLVs Option : Port Description Disable System Name Disable System Description Disable System Capabilities Disable...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide using LLDP. show lldp remote_ports {<portlist>} {mode[brief | normal | Syntax detailed]} The show lldp remote_ports command displays the information Description regarding neighboring devices. <portlist> − A port or range of ports to be displayed.
Page 406
Restrictions Only Administrator or operator-level users can issue this command. Example usage: To configure LLDP management address advertisement: DES-1210-52/ME:5# config lldp ports 1 mgt_addr ipv4 100.1.1.2 enabled Command: config lldp ports 1 mgt_addr ipv4 100.1.1.2 enabled Success. DES-1210-52/ME:5# config lldp ports...
Page 407
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide advertise the switch’s basic TLVs the command is per port on the switch. [<portlist> | all] – Specify a port or ports to be configured. Parameters Basic TLVs: all – Advertisement of all the basic TLVs port description –...
Page 408
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide mac_phy_configuration_status the command is per port on the switch. [<portlist> | all] – Specify a port or ports to be configured. Parameters [enable | disable] - Defines if the advertisement is enabled or disabled.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To configure LLDP mac_phy_configuration status: DES-1210-52/ME:5# config lldp ports all dot1_tlv_vlan_name vlanid 1 disable Command: config lldp ports all dot1_tlv_vlan_name vlanid 1 disable Success. DES-1210-52/ME:5# config lldp ports Purpose To enable or disable LLDP management LLDP power pse TLVs advertisement on a port or ports.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show lldp power_pse_tlv Command: show lldp power_pse_tlv Port State -------------------------------------- Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a ALL...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show lldp statistics To display the Link Layer Discovery Protocol (LLDP) statistics for the Purpose specified ports. Syntax show lldp statistics {ports <portlist>} Description The show lldp statistics command displays the statistics of LLDP on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide ACCESS CONTROL LIST COMMANDS The Access Control List commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter [ ethernet {vlan | source_mac <macmask> | destination_mac <macmask> | 802.1p | ethernet_type} | ip { source_ip_mask <netmask>...
Page 414
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide destination_mac <macmask> – Specifies a MAC address mask for the destination MAC address in the following format: 000000000000-FFFFFFFFFFFF. 802.1p – Specifies that the Switch examine the 802.1p priority value in the frame’s header.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide mask for the destination port. udp – Specifies that the Switch examines each frame’s protocol field and it’s value must be 17 (User Datagram Protocol-UDP) in order for the action to take place..
Page 416
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide deny]] | delete access_id <value (1-128)>] The config access_profile ethernet command defines the rules Description used by the Switch to either filter or forward packets based on the Ethernet part of each packet header.
Page 417
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide more of the following: source_ip <ipaddr> – Specifies that the access profile applies only to packets with this source IP address. protocol_id <value 0-255> – Specifies that the Switch examine the Protocol field in each packet and if this field contains the value entered here, apply the appropriate rules.
Page 418
Only administrator or operate-level users can issue this command. Example usage: To configure a rule for the Ethernet access profile: DES-1210-52/ME:5# config access_profile profile_id 2 add access_id 2 ip protocol_id 2 ports 2 deny Command: config access_profile profile_id 2 add access_id 2 ip protocol_id...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide 2 ports 2 deny Success. DES-1210-52/ME:5# delete access_profile Purpose To delete a previously created access profile delete access_profile profile_id <value 1-10> Syntax Description The delete access_profile command deletes a previously created access profile on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# show access_profile profile_id 1 Command: show access_profile profile_id 1 Access Profile Table Access Profile ID: 1 Type: Ethernet --------------------------------------------------------------------------- --------------------------------------------------------------------------- Mask Option: VLAN 802.1p --------------------------------------------------------------------------- DES-1210-52/ME:5# create cpu_access_profile Purpose To create an access profile on the Switch by examining the Ethernet part of the packet header.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Type field. tcp – Specifies that the Switch examines each frames protocol field and its value must be 6 (Transmission Control Protocol- TCP) for the action to take place. src_port_mask <hex 0x0-0xffff> – Specifies the TCP port mask for the source port.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide profile applies only to packets that have this TCP destination port in their header. flag <string> – Specifies the appropriate flag parameter. src_port <value 0-65535> –Specifies that the cpu access profile applies only to packets that have this TCP source port in their header.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide DES-1210-52/ME:5# delete cpu access_profile profile_id 1 Command: delete cpu access_profile profile_id 1 Success. DES-1210-52/ME:5# enable cpu_interface_filtering Purpose To enable CPU interface filtering on the Switch. enable cpu_interface_filtering Syntax The enable cpu_interface_filtering command is used to enable Description CPU interface filtering on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide show cpu_access_profile Purpose To view the CPU access profile entry currently set in the Switch. show cpu_access_profile {profile_id <value 1-3>} Syntax The show cpu access_profile command is used view the current Description CPU interface filtering entries set on the Switch.
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide TRAFFIC SEGMENTATION COMMANDS The Traffic Segmentation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config <portlist> forward_list [null | <portlist>]...
Page 428
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide Restrictions None. Example usage: To display the current traffic segmentation configuration of ports 1 to 3 on the Switch: DES-1210-52/ME:5# show traffic_segmentation 1-3 Command: show traffic_segmentation 1-3 Port Forward Portlist ---- --------------------------------------------------...
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide SAFEGUARD COMMANDS The Safeguard commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameter config state [enable | disable] safeguard_engine show safeguard_engine...
Page 430
DES-1210-52/ME L2 Metro Ethernet Switch CLI Reference Guide To show the safeguard engine status on the switch: DES-1210-52/ME:5# show safeguard_engine Command: show safeguard_engine Safe Guard : Enabled DES-1210-52/ME:5#...