Yamaha STAR XVS95CE 2DX1 2014 Service Manual page 400

2. Check:
• Crankshaft position sensor resistance
Out of specification → Replace the crank-
shaft position sensor/stator assembly.
Crankshaft position sensor resis-
tance
248–372 Ω
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a. Connect the pocket tester (Ω × 100) to the
crankshaft position sensor coupler as shown.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
• Positive tester probe →
gray "1"
• Negative tester probe →
black "2"
b. Measure the crankshaft position sensor re-
sistance.
▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
EAS28130
CHECKING THE LEAN ANGLE SENSOR
1. Remove:
• Lean angle sensor
2. Check:
• Lean angle sensor output voltage
Out of specification → Replace.
Lean angle sensor output voltage
Less than 45°
0.4–1.4 V
More than 45°
3.7–4.4 V
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a. Connect the test harness-lean angle sensor
(6P) "1" to the lean angle sensor and wire
harness as shown.
b. Connect the pocket tester (DC 20 V) to the
test harness-lean angle sensor (6P).
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼▼▼
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲▲▲
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼▼▼
7-87
ELECTRICAL COMPONENTS
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
Test harness- lean angle sensor
(6P)
90890-03209
YU-03209
• Positive tester probe →
yellow/green (wire harness color)
• Negative tester probe →
black/blue (wire harness color)
45 45
c. Turn the main switch to "ON".
d. Turn the lean angle sensor to 45°.
e. Measure the lean angle sensor output volt-
age.
▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
EAS1TP1006
CHECKING THE STARTER MOTOR
OPERATION
1. Check:
• Starter motor operation
Does not operate → Perform the electric
starting system troubleshooting, starting with
step 4.
Refer to "TROUBLESHOOTING" on page
7-4.
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a. Connect the positive battery terminal "1" and
starter motor lead "2" with a jumper lead "3".
EWA13810
WARNING
• A wire that is used as a jumper lead must
have at least the same capacity of the bat-
tery lead, otherwise the jumper lead may
burn.
• This check is likely to produce sparks,
therefore, make sure no flammable gas or
fluid is in the vicinity.
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲▲▲
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼▼▼