Resistance
7.5–12.5 kΩ
▼
▼▼▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
a. Remove the spark plug cap from the spark
plug lead.
b. Connect the pocket tester (Ω × 1k) to the
spark plug cap as shown.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
c. Measure the spark plug cap resistance.
▲
▲▲▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
EAS28100
CHECKING THE IGNITION COILS
The following procedure applies to all of the igni-
tion coils.
1. Check:
• Primary coil resistance
Out of specification → Replace.
Primary coil resistance
2.16–2.64 Ω
▼
▼▼▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
a. Disconnect the ignition coil connectors from
the ignition coil terminals.
b. Connect the pocket tester (Ω × 1) to the igni-
tion coil as shown.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
• Positive tester probe →
black/red "1"
• Negative tester probe →
orange or gray/red "2"
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲▲▲
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
7-86
ELECTRICAL COMPONENTS
c. Measure the primary coil resistance.
▲
▲▲▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
2. Check:
• Secondary coil resistance
Out of specification → Replace.
Secondary coil resistance
8.64–12.96 kΩ
▼
▼▼▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
a. Disconnect the spark plug cap from the igni-
tion coil.
b. Connect the pocket tester (Ω × 1 k) to the ig-
nition coil as shown.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
• Positive tester probe →
black/red "1"
• Negative tester probe →
spark plug lead "2"
c. Measure the secondary coil resistance.
▲
▲▲▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
EAS28120
CHECKING THE CRANKSHAFT POSITION
SENSOR
1. Disconnect:
• Crankshaft position sensor coupler
(from the wire harness)
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲▲▲
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲▲▲