Miscellaneous Settings - GE Advent Installation Instructions Manual

Battery Voltage Shutdown is Canceled
17040
(Default = 176 (10.4V)) This setting allows you to set the backup
battery voltage at which a system shutdown (during an AC power
failure) is canceled (set in 1/17 volt units).
To set Battery Voltage Shutdown is Canceled:
Once in program mode enter the item number. Enter the desired
voltage (168–184 [9.9–10.8V]) and press
AC Stable Time
17036
(Default = 8 seconds) This setting allows you to specify the time
(in seconds) that AC power must be lost or restored before a
trouble, or trouble restoral is generated. These events are not
reported immediately.
To set AC Report Delay:
Once in program mode enter the item number. Enter the desired
ƒ
time (0–200) and press .
AC Frequency
17123
(Default = 0 [60 Hz]) This setting allows you to choose the AC
frequency that is powering the panel.
To set the AC Frequency:
Once in program mode enter the item number. Enter
0
(off), or for 60 Hz (on). Press
Panel Latitude
17110
(Default = 0 degrees) This setting allows you to specify the
latitude (in degrees) where the panel is located. This information
is then used by the panel when automatically adjusting sunrise/
sunset schedules.
To set the Panel Latitude:
Once in program mode enter the item number. Enter the desired
ƒ
latitude (0–65) and press .
On Premises Pager ID 1
On Premises Pager ID 2
1: 17060, 2: 17061
(Default = 0000000) This setting allows you to specify 7-digit
pager IDs that will identify the 2 different pager groups in a local
paging network.
To specify On Premises Pager IDs:
Once in program mode enter the item number. Enter the desired
7-digit (0–9) pager ID and press
48
(System)
ƒ
.
(System)
(System)
1
for 50 Hz
ƒ
to apply the new setting.
(System)
(System)
ƒ
.

Miscellaneous Settings

Downloader Account Number
17109
(Default = 00000000) The Downloader Account Number is used
to identify the panel to Advent Downloader.
To enter a Downloader Account Number:
1. Once the desired item number has been entered the cur-
rent account number will be displayed.
2. Enter an 8-digit number (0–9) and press
Reset Panel
50001
(Default = n/a) This setting allows you to clear any errors the
panel may have by "rebooting" the system. All settings will
remain unchanged.
To Reset the Panel:
1. Enter the installer code. Enter
99 and then ƒ . Wait about a minute for the panel
2. Press
to reset.
Software/Hardware Version
50003
(Default = n/a) This setting allows you to view and identify panel
hardware and software version.
To view System Version:
1. Enter the installer code.
50003 . The panel displays SYSTEM ID
2. Enter
nnnnnnnn VERSION n.nn nnn.nnn PANEL TYPE n
SNAPCARD n n.
Panel Type Formats
‰ 0—Commercial Burg.
‰ 1—Home Navigator
‰ 2—Commercial Fire
‰ 3—Home Navigator High
‰ 4—Commercial Burg. High
‰ 5—Commercial Fire High
‰ 6—not used
‰ 7—Commercial Burg. Low
‰ 8—Commercial Fire Low
SnapCard Type Formats
‰ 0—none
‰ 1—(not used)
‰ 2—NAC
‰ 3—8Z input
‰ 4—4 relay output
‰ 5—quad smoke loop
‰ 6—24V smoke loop
‰ 7—(not used)
‰ 8—4Z input, 2 relay output
(Customer)
ƒ .
50001 .
Advent Commercial Fire System