Fixed Output Settings - GE Advent Installation Instructions Manual

Delete/Replace LED Module
48010 (Programmable Outputs-LED Module)
(Default = n/a) Use this item number to delete LED modules or
change device IDs. This setting allows you to replace a
malfunctioning LED module without having to reprogram LED
settings.
To Delete/Replace LED Module:
Note
Deleting the module does not delete the bus text associ-
ated with the deleted device. To delete device text use
item number 49002.
1. Once in program mode enter
shows ENTER DEVICE ID OR PRESS * TO CANCEL.
2. Enter the 8-digit device ID of the device you wish to
delete or replace (located on module) and press
3. The display shows ENTER NEW DEVICE ID OR ENTER
0 TO DELETE.
4. Enter a new device ID or enter
displays DEVICE ID xxxxxxxx DELETED, or DEVICE
CHANGE OK.
5. To delete or replace another LED module, repeat the
above procedure.
Keypad Idle Text
49005
(Default = none) Use the following guidelines to add keypad idle
text to the panel. This is the custom text displayed when the
touchpad is not armed.
‰ Use the item numbers that appear in Table B.2 on page 92
(2 digit display descriptors) for characters.
‰ When using characters from Table B.2 to create words,
you must reserve an item number for a 'space' after the
word.
‰ Each character or word uses up one item number. For
example a word (such as EAST WING) counts as nine
item numbers—8 letters and 1 space.
‰ 63 item numbers are reserved for display text in each par-
tition/area so plan ahead before programming text. You
may need to abbreviate words to avoid running out of item
numbers.
To program Keypad Idle Text:
1. Once in program mode enter
shows ENTER PARTITION/AREA NUMBER OR PRESS
* TO CANCEL.
2. Enter the desired partition/area number and press
display shows ENTER DISPLAY NUMBERS OR PRESS
* TO CANCEL.
3. Enter the numbers of the desired characters. If you make
‚ to start over.
a mistake press
4. Once all numbers have been entered, press
To delete Keypad Idle Text:
1. Once in program mode enter
shows ENTER PARTITION NUMBER OR PRESS * TO
CANCEL.
2. Enter the desired partition/area number and press
display shows ENTER DISPLAY NUMBERS OR PRESS
ƒ .
* TO CANCEL. Press
42
48010 . The display
ƒ .
0 . Press ƒ . The panel
(Partitions)
49005 . The display
ƒ . The
ƒ .
49005 . The display
ƒ . The

Fixed Output Settings

The following explains the procedure for programming/
modifying the fixed siren/strobe outputs. Siren/strobe out-
puts can be directed to any SnapCard, Bus Module, or Panel
Output.
Output Configuration
50005
(Default = n/a) Use the procedure below for mapping outputs.
To program an Output:
1. Once in program mode enter
shows ENTER OUTPUT NUMBER OR PRESS * TO
CANCEL.
2. Enter the desired 3-digit output number from the choices
below.
‰ 501–508, Interior siren outputs (1 per partition/area)
‰ 601–608, Exterior siren outputs (1 per partition/area)
‰ 701–708, Strobe outputs (1 per partition/area)
Press ƒ. The display shows OUTPUT TYPE IS n.
3.
ENTER NEW TYPE OR PRESS # TO ACCEPT.
4. Enter the output type from the choices below:
‰ Enter 1 for a Bus Module Output
‰ Enter 3 for a SnapCard Output
‰ Enter 4 for an Panel Output
Press ƒ. The display shows OUTPUT DATA n IS
nnnnnnnn. ENTER OUTPUT DATA n OR PRESS # TO
ACCEPT.
5. Based on the output type, enter the required data from the
choices below.
Bus Module Output
Enter the 8-digit device ID and press #.
ƒ for output data 4. Output data 5 shows
Enter 1 +
00000000. The first 4 places represent outputs 1-4 on a
HOM.
Choose which output(s) to activate. For example, enter-
ing 10010000 activates outputs 1 and 4 on a HOM.
SnapCard Output
Output data 5 shows 00000000. The first 4 places represent
an output SnapCard mounted in the lower slot (SnapCard 1).
The last 4 places represent an output SnapCard mounted in
the side slot (SnapCard 2).
Choose which output(s) to activate. For example, entering
01000010 would activate the second output on SnapCard 1,
and the third output on SnapCard 2.
Panel Output
Output data 5 shows 00000000. The first 6 places repre-
sent general outputs 1–6, 7 represents the panel interior
siren output, and 8 represents the panel exterior siren out-
put.
Choose which output(s) to activate. For example, enter-
ing 11000000 activates onboard outputs 1 and 2.
(Partitions-X10)
50005 . The display
Advent Commercial Fire System