Advanced Settings - GE Advent Installation Instructions Manual

Number of Attempts
zz003
(Default = 3) Set the number of times (attempts) the panel will try
to dial the pager phone number.
To set the Number of Dial Attempts:
Once the item number has been entered, enter the number of dial
ƒ
attempts (3–10) and press .
Comm Format
zz004
(Default = 1 [TAP at 1200 bps PSK]) Select the type of
communication format the panel will use when reporting events
to pagers.
Communication Formats:
‰ Enter 0 for TAP at 300 bps (FSK)
‰ Enter 1 for TAP at 1200 bps (PSK)
To set the Communication Format:
Once the item number has been entered, use the choices above to
select a communication format. Press
Character Format
zz005
(Default = 1 [7/E/1]) Select the character format the panel will use
when reporting to pagers.
Character Formats:
‰ Enter 0 for 8/N/1
‰ Enter 1 for 7/E/1
To set the Character Format:
Once the item number has been entered, press
1
character format (off), or for 7/N/1 character format (on). Press
ƒ
to apply the setting.
Pager System Reports
zz006
(Default = off) Select whether or not you want system events
reported to pager.
To turn System Pager Report On/Off:
Once the item number has been entered, enter
0
setting on (report), or to turn it off (don't report). Press
apply the new setting.
Advent Commercial Fire System
(Phone-Pagers)
(Phone-Pagers)
ƒ
to apply the new setting.
(Phone-Pagers)
0
for 8/N/1
(Phone-Pagers)
1
to turn this
ƒ
to
Partition/Area 1 Pager Reports
Partition/Area 2 Pager Reports
Partition/Area 3 Pager Reports
Partition/Area 4 Pager Reports
Partition/Area 5 Pager Reports
Partition/Area 6 Pager Reports
Partition/Area 7 Pager Reports
Partition/Area 8 Pager Reports
1: zz007, 2: zz008, 3: zz009, 4: zz010,
5: zz011, 6: zz012, 7: zz013, 8: zz014
(Defaults = 0, phone 25-31 = 1) Select whether or not you want
partition/area events to report to pager(s).
To turn Partition/Area Report On/Off:
Once the item number has been entered, enter
0
setting on (report), or to turn it off (don't report). Press
apply the new setting.
Pager PIN #
zz015
(Default = none) Enter up to a 15-digit pager PIN.
To enter a Pager PIN:
1. Enter the desired item number (ex. 25015).
2. Enter up to a 15-digit (0–9) pager PIN.
ƒ and the touchpad displays the pager PIN.
3. Press
Pager Max Message Length
zz016
(Default = 120 characters) Set the maximum character length for
pager messages.
To set the maximum Pager Message Length:
Once the item number has been entered, enter the maximum
pager length (0–255) and press

Advanced Settings

$87,21
Only qualified persons should make changes to advanced
phone settings.
Maximum Ring Cycle Time
17018 (Phone-Advanced Dialog Screen)
(Default = 67 milliseconds) Specify (in milliseconds) the
maximum cycle time for a ring signal.
To set the Maximum Ring Cycle Time:
Once the item number has been entered, specify the maximum
ring cycle time (0–255). Press
(Phone-Pagers)
1
to turn this
ƒ
(Phone-Pagers)
(Phone-Pagers)
ƒ
.
ƒ
to apply the new setting.
to
31