Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for GE NETWORX NX-108E
Summary of Contents for GE NETWORX NX-108E
- Page 1 NETWORX NX-4 User manual...
- Page 3 SECURITY SYSTEM NOTES Installing/Service Company _________________________________ For Service Call __________________________________________ Central Station ___________________________________________ Duress Code ____________________ FUNCTION CODES Function Code Controls Function EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary Emergency Police PROGRAMMED FUNCTIONS Abort Delay (s) Cancel Alarm Group Bypass (s) Auto Bypass (s) Chime Quick Arm (s)
- Page 4 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY.
-
Page 5: Table Of Contents
TABLE OF CONTENTS GLOSSARY OF TERMS ..............4 UNDERSTANDING THE LIGHTS .............5 Armed Light ..................5 Bypass Light..................5 Cancel Light ..................5 Chime Light ..................5 Exit Light...................5 Fire Light ..................5 Instant Light..................5 Power Light ..................5 Ready Light ..................5 Stay Light ..................6 Zone Light ..................6 EMERGENCY ACTIVATION KEYS ..........6 KEYPAD FUNCTIONS... -
Page 6: Glossary Of Terms
GLOSSARY OF TERMS Abort Delay: An option that allows a delay in reporting to the central station. There is a communicator delay of 30 seconds. It can be removed, or increased up to 45 seconds at the option of the end user by consulting with the installer. Authority Level: The level of access an individual has when using an alarm panel. -
Page 7: Understanding The Lights
UNDERSTANDING THE LIGHTS Armed Light The armed light is “on” when the system is armed. The armed light is “off” when it is disarmed. The armed light will flash when there has been an alarm during the previous arm cycle. Bypass Light The bypass light is “on”... -
Page 8: Stay Light
Stay Light The stay light is “on” when the all interior (motion detector) zones are bypassed. Zone Light The zone lights are “off” when everything is normal. A zone light will be “on” if the zone has been bypassed. If a zone light is “flashing”, that zone is in alarm or has been faulted. -
Page 9: Keypad Functions
KEYPAD FUNCTIONS ARMING YOUR SYSTEM IN THE “AWAY” MODE AWAY is used when the user is away from the premise and wants the interior protected. Listed below are the steps to arm in the AWAY Mode: Step 1 Close all protected doors and windows. •... -
Page 10: Using The Quick Arm
• Press the [STAY] key. Step 3 • The stay light will illuminate indicating that all interior zones are bypassed. (All interior devices will bypass automatically, giving the user freedom of movement within the interior area.) • The bypass light will illuminate if any zone(s) are bypassed. If any zone(s) have been bypassed previously by the user, the light(s) corresponding to the bypassed zone(s) will illuminate, alerting the user that a zone(s) may be unprotected and can be faulted without... -
Page 11: Cancel / Abort Feature
CANCEL / ABORT FEATURE (Optional, see page 1) The cancel light will flash during an abort delay time. If a code is entered followed by the [CANCEL] key while this light is flashing, all abortable reports will stop the communication process. Entering a code followed by the [CANCEL] key during or after an alarm report to the central station will cause the cancel light to come on. -
Page 12: Changing User Codes
CHANGING USER CODES Step 1 Your system must be in the Disarmed state to change user codes. Step 2 Press [r]-[5]. Step 3 Enter a “Master Arm/Disarm Code”. Step 4 The ready light will flash. Step 5 Enter the 2-digit “user number” (always enter 2 digits such as [0] - [3] for user 3). -
Page 13: Other Keypad Functions
LIGHT AUTHORITY LEVELS IF LIGHT 8 IS OFF Reserved (Note: Do not change if on.) Arm Only Arm Only After Closing Time Master Arm/Disarm (can program other codes) Arm/Disarm Bypass Zones Open / Close Reporting If this light is on, this code is programmed as a function code. -
Page 14: Test Function
TEST FUNCTION – Optional If programmed, this function will perform a battery test, communicator test, and/or a siren test. No alarms will be sent and no reports will be sent unless a communicator test is performed, at which time a test signal will be sent. Step 1 Press [r]-[4]. -
Page 15: Setting The System Clock
Step 3 Enter the “Day of Week “ 1 = Sunday 3 = Tuesday 5 = Thursday 7 = Saturday 2 = Monday 4 = Wednesday 6 = Friday Step 4 Enter the “Month Code”. Must always be two (2) digits. 01 = January 05 = May 09 = September... -
Page 16: Keypad Control Tones (Beeps)
KEYPAD CONTROL TONES (BEEPS) A sounder is built into the keypad. If programmed, your system keypad may sound for any of the following reasons: Beeps for all keypresses. Sounds a continuous tone during the Entry delay time. Pulses when a day zone is violated while the system is disarmed. Pulses when a FIRE zone has a trouble condition. -
Page 17: Service Menu
SERVICE MENU The service light will be “on” if the security system requires service. If the service light is “on”, press the [r] key followed by the [2] key to determine the service condition. One or more zone lights will illuminate indicating what service(s) is required. -
Page 18: Emergency Evacuation Plans
EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building. Draw up a floor plan of your home. - Page 19 SYSTEM NOTES...
- Page 20 NX-4 USER’S MANUAL NX4UD04 REV D (FEB 2004)