D-Link DXS-1210-12TC Reference Manual page 46

any} {DST-IP-ADDR DST-IP-WILDCARD | host DST-IP-ADDR | any} {DST-MAC-ADDR DST-
MAC-WILDCARD | host DST-MAC-ADDR | any} [cos OTER-COS] [vlan OUTER-VLAN]
[fragments] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range PROFILE-
NAME]
rule [SEQUENCE-NUMBER] {permit | deny} tcp {SRC-IP-ADDR SRC-IP-WILDCARD | host
SRC-IP-ADDR | any} {SRC-MAC-ADDR SRC-MAC-WILDCARD | host SRC-MAC-ADDR | any}
[{eq | lt | gt | neq} PORT | range MIN-PORT MAX-PORT] {DST-IP-ADDR DST-IP-WILDCARD |
host DST-IP-ADDR | any} {DST-MAC-ADDR DST-MAC-WILDCARD | host DST-MAC-ADDR |
any} [{eq | lt | gt | neq} PORT | range MIN-PORT MAX-PORT] [TCP-FLAG] [cos OUTER-COS]
[vlan OUTER-VLAN] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range
PROFILE-NAME]
rule [SEQUENCE-NUMBER] {permit | deny} udp {SRC-IP-ADDR SRC-IP-WILDCARD | host
SRC-IP-ADDR | any} {SRC-MAC-ADDR SRC-MAC-WILDCARD | host SRC-MAC-ADDR | any}
[{eq | lt | gt | neq} PORT | range MIN-PORT MAX-PORT] {DST-IP-ADDR DST-IP-WILDCARD |
host DST-IP-ADDR | any} {DST-MAC-ADDR DST-MAC-WILDCARD | host DST-MAC-ADDR |
any} [{eq | lt | gt | neq} PORT | range MIN-PORT MAX-PORT] [cos OUTER-COS] [vlan
OUTER-VLAN] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range PROFILE-
NAME]
rule [SEQUENCE-NUMBER] {permit | deny} icmp {SRC-IP-ADDR SRC-IP-WILDCARD | host
SRC-IP-ADDR | any} {SRC-MAC-ADDR SRC-MAC-WILDCARD | host SRC-MAC-ADDR | any}
{DST-IP-ADDR DST-IP-WILDCARD | host DST-IP-ADDR | any} {DST-MAC-ADDR DST-MAC-
WILDCARD | host DST-MAC-ADDR | any} [ICMP-TYPE [ICMP-CODE] | ICMP-MESSAGE] [cos
OUTER-COS] [vlan OUTER-VLAN] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP]
[time-range PROFILE-NAME]
no SEQUENCE-NUMBER
Parameters
SEQUENCE-NUMBER
cos OUTER-COS
vlan OUTER-VLAN
any
host SRC-MAC-ADDR
SRC-MAC-ADDR SRC-MAC-
WILDCARD
host DST-MAC-ADDR
DST-MAC-ADDR DST-MAC-
WILDCARD
PROTOCOL
host SRC-IP-ADDR
SRC-IP-ADDR SRC-IP-
WILDCARD
host DST-IP-ADDR
DST-IP-ADDR DST-IP-
WILDCARD
precedence PRECEDENCE
DXS-1210 Series Smart Managed Switch CLI Reference Guide
Specifies the sequence number. The range is from 1 to 65535. The
lower the number is, the higher the priority of the permit/deny rule.
(Optional) Specifies the outer priority value. This value must be
between 0 and 7.
(Optional) Specifies the outer VLAN ID.
Specifies to use any source MAC address, any destination MAC
address, any source IP address, or any destination IP address.
Specifies a specific source host MAC address.
Specifies a group of source MAC addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to bit value 0 will be checked.
Specifies a specific destination host MAC address.
Specifies a group of destination MAC addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
(Optional)Specifies the IP protocol ID. Enter the following keywords:
eigrp, esp, gre, igmp, ospf, pim, vrrp, pcp, and ipinip.
Specifies a specific source host IP address.
Specifies a group of source IP addresses by using a wildcard bitmap.
The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
Specifies a specific destination host IP address.
Specifies a group of destination IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
(Optional) Specifies that packets can be filtered by precedence level,
as specified by a number from 0 to 7.
43