B: Application; B: Application; B1: Operation Mode Selection; B2: Dc Injection Braking And Short Circuit Braking - YASKAWA Z1000 User Manual

B.2 b: Application
B.2 b: Application
Application parameters configure the source of the Run command, DC Injection Braking, Speed Search, timer functions, PI
control, Energy Savings, and a variety of other application-related settings.
u

b1: Operation Mode Selection

No.
(Addr. Name
Hex)
Frequency Reference
b1-01
Selection for AUTO
(180)
mode
Run Command
b1-02
Selection for AUTO
(181)
mode
b1-03 Stopping Method
(182) Selection
b1-04 Reverse Operation
(183) Selection
Run Command
b1-08
Selection in
(187)
Programming Mode
b1-11 Drive Delay Time
(1DF) Setting
b1-14
Phase Order Selection
(1C3)
b1-17 Run Command at Power
(1C6) Up
u

b2: DC Injection Braking and Short Circuit Braking

No.
(Addr. Name
Hex)
b2-01 DC Injection Braking
(189) Start Frequency
b2-02 DC Injection Braking
(18A) Current
b2-03 DC Injection Braking
(18B) Time at Start
b2-04 DC Injection Braking
(18C) Time at Stop
b2-09 Motor Pre-Heat Current
(1E1) 2
284
LCD Display
Ref Source 1 0: HOA keypad
0: Operator 1: Terminals (Analog Input Terminals)
1: Analog Input 2: Serial communications (APOGEE FLN, BACnet,
2: Serial Com MEMOBUS/Modbus, or Metasys N2)
3: Option PCB 3: Option card
Run Source 1 1: Control Circuit Terminal
1: Digital Inputs 2: Serial communications (APOGEE FLN, BACnet,
2: Communication MEMOBUS/Modbus, or Metasys N2)
3: Option PCB 3: Option card
Stopping Method 0: Ramp to stop
0: Ramp to Stop 1: Coast to stop
1: Coast to Stop 2: DC Injection Braking to stop
2: DCInj to Stop 3: Coast with timer
3: Coast w/Timer
Reverse Oper 0: Reverse enabled
0: Reverse Enabled 1: Reverse disabled
1: Reverse Disabled
RUN dur PRG Mode 0: Run command is not accepted while in Programming Mode
0: Run 1: Run command is accepted while in Programming
Disabled@PRG 2: Prohibit entering Programming Mode during Run
1: ModeRun
Enabled@PRG
2: Prg only @ Stop
After a Run command is entered, the drive output waits until
Run Delay Time this delay time has passed before starting.
Rotation Sel 0: Standard
0: Standard 1: Switch phase order (reverses the direction of the motor)
1: SwitchPhaseOrder
0: Disregarded.
Run Cmd @ Pwr On A new Run command must be issued after power up.
0: Cycle Ext Run 1: Allowed.
1: Accept Ext Run Motor will start immediately after power up if a Run command
is already enabled.
LCD Display
Sets the frequency at which DC Injection Braking starts when
"Ramp to stop" (b1-03 = 0) is selected.
DCInj Start Freq
Sets the DC Injection Braking current as a percentage of the
DCInj Current drive rated current.
Sets DC Injection Braking time at start. Disabled when set to
DCInj Time@Start 0.00 seconds.
Sets DC Injection Braking time at stop.
DCInj Time@Stop
Determines the percentage of motor rated output current used
Preheat Current for the motor pre-heat function.
Description
Description
YASKAWA ELECTRIC TOEP C710616 45F YASKAWA AC Drive – Z1000 User Manual
Values Page
Default: 1
127
Range: 0 to 3
Default: 1
129
Range: 1 to 3
Default: 1
129
Range: 0 to 3
Default: 1
158
Range: 0, 1
Default: 0
–
Range: 0 to 2
Default: 0 s
Min.: 0 –
Max.: 600
Default: 0
158
Range: 0, 1
Default: 1
158
Range: 0, 1
Values Page
<1>
Default:
158
Min.: 0.0 Hz
Max.: 10.0 Hz
Default: 50%
Min.: 0 159
Max.: 100
Default: 0.00 s
Min.: 0.00 159
Max.: 10.00
Default: 0.00 s
Min.: 0.00 159
Max.: 10.00
Default: 5%
Min.: 0 –
Max.: 100