YASKAWA Z1000 User Manual page 395

Speed Search Delay Time ..................................................... 160
Speed Search Detection Compensation Gain ............................... 161
Speed Search Induced Voltage Level ........................................ 162
Speed Search Method Selection .............................................. 161
Speed Search Restart Current Level.......................................... 161
Speed Search Restart Detection Time........................................ 161
Speed Search Selection at Start ............................................... 160
Speed Search Wait Time....................................................... 162
Stall Prevention ................................................................. 202
Stall Prevention Level during Acceleration ................................. 314
Stall Prevention Level during Run ........................................... 314
Stall Prevention Limit during Acceleration ................................. 314
Stall Prevention Selection during Acceleration............................. 314
Stall Prevention Selection during Deceleration............................. 314
Stall Prevention Selection during Run ....................................... 314
Standard Connection Diagram ..................................................62
Standards......................................................................... 275
Starting Torque.................................................................. 274
Start Speed Search Select...................................................... 162
Start-Up Flowcharts ............................................................ 119
Stationary Auto-Tuning........................................................ 145
Stationary Auto-Tuning for Line-to-Line Resistance ...................... 143
Status Display ................................................................... 123
STo ............................................................................... 217
STOP Key Function Selection ................................................ 190
Stopping Method after Communication Error ........................ 179, 346
Stopping Method Selection.................................................... 129
Storage Temperature .............................................................42
Supported Properties of Objects .............................................. 352
Surrounding Area .................................................................42
T
T/L3.................................................................................81
T1-03 ............................................................................. 146
T1-04 ............................................................................. 146
T1-05 ............................................................................. 146
T1-06 ............................................................................. 146
T1-07 ....................................................................... 146, 147
T1 Tuning Start ................................................................. 330
T2 Tuning Start ................................................................. 150
Task Complete .................................................................. 233
TdE ............................................................................... 217
Temperature Derating .......................................................... 279
Terminal A1 Bias Setting...................................................... 137
Terminal A1 Function Selection.............................................. 177
Terminal A1 Gain Setting ..................................................... 137
Terminal A1 Signal Level Selection ......................................... 176
Terminal A2 Bias Setting...................................................... 138
Terminal A2 Function Selection.............................................. 177
Terminal A2 Gain Setting ..................................................... 138
Terminal A2 Signal Level Selection ......................................... 177
Terminal Block Configuration ..................................................68
Terminal Board .............................................................. 34, 35
Terminal Board Connection Error............................................ 208
Terminal Board Error .......................................................... 209
Terminal Connections for Communication Self-Diagnostics............. 360
Terminal Cover ............................................ 32, 33, 34, 35, 36, 70
Terminal TB1 .....................................................................37
Terminal TB2 .....................................................................37
Terminal TB3 .....................................................................37
YASKAWA ELECTRIC TOEP C710616 45F YASKAWA AC Drive – Z1000 User Manual
Terminal TB4 .....................................................................37
Terminal TB5 .....................................................................37
Test Run.................................................................... 144, 147
Test Run Checklist.............................................................. 155
Test Run with Load Connected ............................................... 152
Third Line Monitor Selection ................................................. 188
Tightening Torque ................................................................83
TIM ............................................................................... 217
Time Data Error................................................................. 217
Time Not Set .................................................................... 217
Time to Continue Making Fault Restarts .................................... 315
Too Many Speed Search Restarts............................................. 217
Torque Compensation Gain ................................................... 200
Torque Compensation Primary Delay Time ................................ 200
Torque Detection Level 1................................................ 142, 316
Torque Detection Selection 1 ........................................... 141, 316
Torque Detection Time 1 ................................................ 142, 316
Torque Specifications, Three Phase 200 V Class ............................83
Torque Specifications, Three Phase 400 V Class ............................85
Troubleshooting without Fault Display...................................... 237
TrPC .............................................................................. 225
Tuning Errors.................................................................... 203
Types of Alarms, Faults, and Errors ......................................... 203
Types of Auto-Tuning for Induction Motors................................ 143
Types of Auto-Tuning for Permanent Magnet Motors .................... 144
U
U/T1 ................................................................................81
U1-01 ............................................................................. 240
U1-07 ............................................................................. 238
U2, U3 Initialization............................................................ 192
U2, U3 Initial Value Selection ................................................ 323
UL3 ......................................................................... 218, 225
UL6 ......................................................................... 218, 225
UL Standards .................................................................... 372
UL Standards Compliance..................................................... 372
Undertorque Detection 1................................................. 218, 225
Undertorque Detection 6....................................................... 225
Undervoltage .................................................................... 225
Undervoltage 3 .................................................................. 219
Undervoltage 3 (Soft-Charge Circuit Fault)................................. 219
Undervoltage Detection Level (Uv1) ........................................ 313
Undervoltage Protection ....................................................... 275
Unexpected Noise from Connected Machinery............................. 242
Unit Code ........................................................................ 190
Unit Selection for MEMOBUS/Modbus Register 0025H........... 180, 348
Unstable Motor Speed when Using PM ..................................... 243
Up Arrow Key................................................................... 107
USB Copy Unit ........................................................... 154, 248
USB port (type-B) ...............................30, 31, 32, 33, 34, 35, 36, 102
User-Defined Parameter Upper/Lower ...................................... 190
User Monitor Selection after Power Up ..................................... 187
User Monitor Selection Mode................................................. 188
User Parameter Automatic Selection................................... 153, 283
User Parameter Default Value .......................................... 142, 322
User Parameter Default Values ............................................... 153
User Parameters 1 to 32.................................................. 153, 283
User-Set Display Units Decimal Display.................................... 189
User-Set Display Units Maximum Value.................................... 189
Uv ................................................................................. 225
Index
395