Huawei Quidway S7700 Configuration Manual - Ethernet page 251
Smart routing switch
Hide thumbs
Also See for Quidway S7700:
- Configuration manual (833 pages) ,
- Configuration manual - multicast (551 pages) ,
- Hardware description (205 pages)
Table of Contents
Advertisement
Quidway S7700 Smart Routing Switch
Configuration Guide - Ethernet
[P-Vlanif30] mpls
[P-Vlanif30] mpls ldp
[P-Vlanif30] quit
# Configure PE2.
[PE2] mpls lsr-id 3.3.3.9
[PE2] mpls
[PE2-mpls] quit
[PE2] mpls ldp
[PE2-mpls-ldp] quit
[PE2] interface vlanif 30
[PE2-Vlanif30] mpls
[PE2-Vlanif30] mpls ldp
[PE2-Vlanif30] quit
Step 4 Create remote LDP sessions between PEs.
# Configure PE1.
[PE1] mpls ldp remote-peer 3.3.3.9
[PE1-mpls-ldp-remote-3.3.3.9] remote-ip 3.3.3.9
[PE1-mpls-ldp-remote-3.3.3.9] quit
# Configure PE2.
[PE2] mpls ldp remote-peer 1.1.1.9
[PE2-mpls-ldp-remote-1.1.1.9] remote-ip 1.1.1.9
[PE2-mpls-ldp-remote-1.1.1.9] quit
After the configuration, run the display mpls ldp session command on PE1 to view the status
of the LDP session. You can see that an LDP session is set up between PE1 and PE2.
Take the display on PE1 as an example.
<PE1> display mpls ldp session
------------------------------------------------------------------------------
Peer-ID
------------------------------------------------------------------------------
2.2.2.9:0
3.3.3.9:0
------------------------------------------------------------------------------
TOTAL: 2 session(s) Found.
LAM : Label Advertisement Mode
Step 5 Enable MPLS L2VPN on the PEs and establish VC connections.
# Configure PE1: Create a VC connection on GE 1/0/0.1, which is connected to CE1.
[PE1] mpls l2vpn
[PE1-l2vpn] mpls l2vpn default martini
[PE1-l2vpn] quit
[PE1] interface gigabitethernet 1/0/0.1
[PE1-GigabitEthernet1/0/0.1] control-vid 1000 dot1q-termination
[PE1-GigabitEthernet1/0/0.1] dot1q termination vid 10
[PE1-GigabitEthernet1/0/0.1] mpls l2vc 3.3.3.9 101
[PE1-GigabitEthernet1/0/0.1] quit
# On PE2, create a VC connection on GE 2/0/0.1, which is connected to CE2.
[PE2] mpls l2vpn
[PE2-l2vpn] mpls l2vpn default martini
[PE2-l2vpn] quit
[PE2] interface gigabitethernet 2/0/0.1
[PE2-GigabitEthernet2/0/0.1] control-vid 2000 dot1q-termination
[PE2-GigabitEthernet2/0/0.1] dot1q termination vid 10
Issue 01 (2011-07-15)
LDP Session(s) in Public Network
Status
LAM
Operational DU Passive
Operational DU Passive
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
SsnRole
SsnAge
000:15:29
3717/3717
000:00:00
2/2
SsnAge Unit : DDD:HH:MM
5 QinQ Configuration
KA-Sent/Rcv
234
Advertisement
Table of Contents
