Chamberlain 1000A Instructions Manual page 41

21
Placering af vægkontrolpanelet
Vægkontrolpanelet monteres 1,5 m over
garagegulvet uden for selve port- og
portskinneområdet, men således, at garageporten
kan ses tydeligt. Panelet skal også placeres
således, at børn ikke kan nå det.
Misbrug af portåbneren kan på grund af den
åbnende og lukkende garageport forårsage
alvorlige personskader. Børn må ikke betjene
vægkontrolpanelet eller fjernbetjeningen.
Som en sikkerhedspåmindelse skal
advarselsmærkaten være permanent anbragt ved
siden af vægkontrolpanelet.
På bagsiden af vægkontrolpanelet (2) er der 2
skrueklemmer (1). Enden af ringeledningen (4)
afisoleres på ca. 6 mm. Trådene trækkes så meget fra
hinanden, at den hvid-røde tråd kan tilsluttes til
skrueklemmen (RED) (1) og den hvide tråd til
skrueklemmen (WHT) (2).
Vægkontrolpanelet monteres med de medfølgende
pladeskruer (3) på en indvendig garagevæg. På tørre
vægge bores hullerne med 4mm diameter og dyvlerne
isættes. Det anbefales at montere panelet ved siden af
sideindgangen til garagen således, at børn ikke kan
når det.
Ringeledningen føres op ad væggen og under loftet
frem til portåbneren. Til fastgørelse af ledningen
anvendes ledningsholderne. Lyntilslutningsklemmerne
på modtageren findes under afdækningsskærmen til
portåbnerlyset. Ringeledningen tilsluttes til klemmerne
som følger: Rød-hvid til rød og hvid til hvid (5).
Aktivering af tasten
Der trykkes én gang på tasten for at åbne resp. lukke
porten. For at stoppe porten under dennes bevægelse
trykkes der én gang til på tasten.
114A2910E-DK
3
2
1
RED WHT
1
(Models 800A, 1000A)
1
2
1
(Model 600A)
5
1 2 3
O –
180 s 60 s
120 s
6mm
4
8-DK
22
Program your Opener & Remote
Activate the opener only when door is in full view,
free of obstruction and properly adjusted. No one
should enter or leave garage while door is in
motion. Do not allow children to operate push
3
button(s) or remote(s). Do not allow children to
play near the door.
Your garage door opener receiver and remote control
transmitter are set to a matching code. If you
purchase additional remote controls, the garage door
opener must be programmed to accept the new
remote code.
Program the Receiver to Match Additional Remote
Control Codes:
Using the orange "LEARN" Button:
1. Press and release the orange "learn" button on the
opener. The learn indicator light will glow steadily
3
for 30 seconds (1).
2. Within 30 seconds, press and hold the button on
the hand-held remote that you wish to operate your
garage door (2).
3. Release the button when the opener light blinks. It
has learned the code. If the light bulb is not
installed, two clicks will be heard (3).
Using the Multi-Function Door Control:
1. Press and hold the button on the hand-held remote
that you wish to operate your garage door (4).
2. While holding the remote button, press and hold the
LIGHT button on the Multi-Function Door
Control (5).
3. Continue holding both buttons while you press the
push bar on the Multi-Function Door Control (all
three buttons are held) (6).
4. Release buttons when the opener light blinks. It has
learned the code. If the light bulb is not installed,
two clicks will be heard (7).
Now the opener will operate when the remote control
push button is pressed. If you release the remote
control push button before the opener light flashes,
the opener has not learned the code.
To Erase all Remote Control Codes:
To deactivate any unwanted remote, first erase all
codes: Press and hold the orange "learn" button on
opener until the learn indicator light goes out
(approximately 6 seconds). All previous codes are
now erased. Reprogram each remote or keyless entry
you wish to use.
3-Channel Remote:
If provided with your garage door opener, the large
button is factory programmed to operate it. Additional
buttons on any rolling code 3-channel remote or
mini-remote can be programmed to operate this or
other rolling code garage door openers.
23
Open/Close/Stop Operation
(only if you have a Multifunction door control)
Your remote control can be programmed to operate
one door using all 3 buttons: the left button will only
open the door, the middle button will only close the
door, and the third button will stop the door's
movement. You may set up this feature as follows:
1. With the door closed, press and hold the left
remote push button.
2. Press and hold the Lock button on the door
control.
3. Press and hold the door control push bar.
–
O
180 s 60 s
120 s
1 2 3
4 5 6 7
LOCK
Open
Close
Stop
When the opener lights flash, release all buttons. Test
by pressing the left (Open) button on the remote. The
door should open. Press it again while the door is
open and nothing should happen. Press the middle
(Close) button and the door should close. Press the
third (Stop) button while the door is moving and it
should stop immediately.
8-GB
114A2910E-GB
1 2 3