Factory Settings That Change With The Control Method (A1-02) - YASKAWA varispeed G7 CIMR-G7B series Instruction Manual

Factory Settings that Change with the Control Method (A1-02)

The factory settings of the following user constants will change if the control method (A1-02) is changed.
Con-
stant
Number
Speed search selection
b3-01
起动速度搜索
Speed search operating current
b3-02
速度搜索电流
Energy-saving gain
b8-02
节能增益
Energy-saving filter time constant
b8-03
节能滤波 时间
Slip compensation gain
C3-01
滑差补偿增益
Slip compensation primary delay time
C3-02
滑差补偿时间
Torque compensation primary delay time
constant
C4-02
转矩补偿延迟时间
ASR proportional (P) gain 1
C5-01
比例增益 1
ASR integral (I) time
C5-02
积分时间 1
ASR proportional (P) gain 2
C5-03
比例增益 2
ASR integral (I) time 2
C5-04
积分时间 2
ASR primary delay time
C5-06
ASR 延迟时间
Carrier frequency selection
C6-02
载波频率选择
Torque reference delay time
d5-02
转矩控制延迟时间
Max. output frequency (FMAX)
E1-04
E3-02
最高输出频率
Max. voltage (VMAX)
E1-05
E3-03
最大电压
Base frequency (FA)
E1-06
E3-04
基本频率
Mid. output frequency (FB)
E1-07
E3-05
中间频率
-86
5
Name
Setting Range
Display
0 to 3
0 to 200
0.0 to 10.0
0.0 to 10.00
0.0 to 2.5
0 to 10000
0 to 10000
0.00 to 300.00
0.000 to 10.000
0.00 to 300.00
0.000 to 10.000
0.000 to 0.500
1 to F
0 to 1000
0.0 to 400.0
0.0 to 255.0
0.0 to 400.0
0.0 to 400.0
Unit
V/f V/f with
Control PG
1 2
1% 120
0.1 -
0.01 s -
0.1 0.0
1 ms 2000
200 200
1 ms
*5
0.01 - 0.20
0.001 s - 0.200
0.01 - 0.02
0.001
- 0.050
sec.
0.001 -
*6 *7
-
6 6
1 ms -
50.0 50.0
*4
0.1 Hz
*3
200.0 200.0
0.1 V
*3
50.0 50.0
0.1 Hz
*3
2.5 2.5
0.1 Hz
*3
Factory Setting
Open- Open
loop Flux Loop
Vector Vector Vector
1 2
3 2 - 2
- 100 - 10
- 0.7 1.0 0.7
- 0.50 0.01 0.50
- 1.0 1.0 1.0
- 200 - -
20 - -
*5
- 20.00 10.00
- 0.500 0.500
- 20.00 10.00
- 0.500 0.500
- - 0.004 0.035
*7 *7 *7 *7
6 1 1
- - 0 10
50.0 50.0 50.0
*3
200.0 200.0 200.0
*3
50.0 50.0 50.0
*3
3.0 0.0 0.0
*3